Smithco Spray Star 3185 User manual

Spray Star 3185/3186
SharpShooter-Rate Sync w/ Envizo Pro II
for 18’ and 20’ Booms
July 2016
Operator’s
Product Support: Hwy SS & Poplar Ave; Cameron WI 54822
1-800-891-9435 [e-mail]

Introduction Operation SprayingProcedures Nozzle Charts Reference
CONTENTS
Introduction................................................................ 1-11
Introduction ................................................................. 1
Symbols................................................................... 2-3
Safety.......................................................................... 4
Safety Decal Location................................................. 5
General Safe Practices............................................... 6
Safe Spraying Practices ............................................. 7
Specifications.............................................................. 8
Optional Spray Equipment .......................................... 8
Set Up ......................................................................... 9
Controls & Instruments.........................................10-11
Operation ................................................................. 12-26
Operating Instructions.......................................... 12-14
Envizio Pro II Do’s and Don’ts................................... 14
SharpShooter-Rate Sync Console Features ............ 15
Initial Set Up of Envizio Pro II................................ 16-19
SharpShooter-Rate Sync Control ........................ 20-21
Spray Operation ........................................................ 22
SprayIntroduction ..................................................... 23
Re-Calibration of Flow Meter..................................... 23
Turf Management ...................................................... 24
Hose & Handgun Spraying ........................................ 24
NozzleTroubleshooting ....................................... 25-26
Reference ................................................................ 27-32
Collection Times ....................................................... 27
Blended Pulse Tip Selection Guide ........................... 28
Declaration of Conformity ......................................29-30
Quick Reference .................................................................32

1
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
INTRODUCTION
Read this manual and all other manuals pertaining to the Spray Star 3180 carefully as they contain safety, oper-
ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment
damage.
Keepmanuals ina safe place after operatorand maintenancepersonnel have read them. Rightand leftsides are
fromthe operator’s seat,facing forward.
All SmithcoSmithco
SmithcoSmithco
Smithco machineshave a Serial Numberand Model Number. Both numbers are needed when ordering
parts. The serial number plate on the Spray Star 3180 is located on top of the frame, between the hydro pump
andspray tank.Refer to engine manual for placementof engineserial number.Refer toengine manualfor place-
mentof engine serial number.
For product and accessory information, help finding a dealer, or to register your procuct please contact us at
www.Smithco.com.
Informationneededwhenordering replacement parts:
1. ModelNumberof machine
2. SerialNumberof machine
3. Nameand PartNumber of part
4. Quantityof parts
For easy access record your Serial and Model numbers here.
lb/kg Empty lb/kg Full
CALIFORNIA
Proposition 65 Warning
Engineexhaust and some of its constituents
are known to the State of California to
cause cancer, birth defects, and other
reproductive harm.
WARNING

2
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SYMBOLS
ParkBrake Park Brake
Release HydraulicOil
Level
Choke-OpenChoke- ClosedHandThrottle
HourMeter HourMeter Fuse
GlowPlugGlowPlug -OffGlow Plug - On
RPM Gasoline Diesel
Water
Temperature
Temperature
Light
EngineOil
Engine - Stop Engine - Start Engine -Run
No Electrical
Power
ElectricalPower
ReadOperator’s
Manual

3
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SYMBOLS
NoSmoking MovingParts Manual
Operation
Pinch Point Step HotSurface
HydraulicFluid
Penetration LiftArm Tractor
Engage Disengage PTO
GroundSpeed Fast Slow
HHigh LLow FForward
RReverse NNeutral Warning
Danger
Caution
Up/RaiseDown/LowerUp/DownArrow

4
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SAFETY
Readand understand this manual and all safety signs before operating and maintaining. Review the safety
instructionsand precautions annually.
TAKE NOTE! THIS SAFETYALERT SYMBOL FOUND THROUGHOUT THIS MANUALIS USED TO CALL
YOURATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONALSAFETYAND THE SAFETY OF
OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
SAFETY SIGNAL WORDS
Notethe use of the signalwords DANGER, WARNING and
CAUTIONwith the safety messages. The appropriate
signalword for each has beenselected using the following
guidelines:
DANGER: Red.Indicates an imminentlyhazardous situa-
tion that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations typically for machine components which, for
functionalpurposes, cannotbe guarded.
WARNING: Orange. Indicates a potentially hazardous
situation that, if not avoided, could result in death or serious
injury, and includes hazards that are exposed when guards
are removed. It may also be used to alert against unsafe
practices.
CAUTION: Yellow. Indicates a potentially hazardous
situation that, if not avoided, may result in minor or moder-
ate injury. It may also be used to alert against unsafe
practices.
IMPORTANT: Blue.Indicatesprocedureswhichshouldbe followedtoavoiddamagetothemachine.
Safety Alert Symbol
This symbol with a warning statement means:
“Warning, be alert! Your safety is involved!”
Carefully read the message that follows.

5
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SAFETYDECALLOCATION
REMEMBER: If Safety Decals** have been damaged, removed, become illegible or parts
replaced without decals, new decals must be applied. New decals are available from
your authorized distributor.
This is a list of decals located on the Spray Star 3180. Part number, description and location will help in reorder-
ing a decals.
A 15-463 DecalSprayPump
25-375 Decal, 94 dBA
B 25-277 Decal,Battery Warning
C 25-286 Decal, Pinch Point
D 25-298 Decal,Warning Hot
E 25-321 Decal, Diesel Fuel Only
F 20-545 Decal,Dash Panel
G 30-157 Decal,Control Panel

6
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SAFEPRACTICES
1. It is your responsibility to read this manual and all publications associated with this machine.
2. Neverallow anyoneto operateor servicethe machineor itsoptional equipmentwithout propertraining and
instructions.Never allowminors tooperate anyequipment.
3. Learnthe properuse of themachine, the locationand purpose ofall the controls and gauges before you
operatethe equipment. Working with unfamiliarequipment can leadto accidents.
4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,
hands and feet. Operate the machine only in daylight or in good artificial light.
5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.
Bewareof overhead obstructionsand undergroundobstacles.Stayalertforhidden hazards.
6. Neveroperate equipmentthat is not in perfectworking order orwithout decals, guards, shields, orother
protectivedevices in place.
7. Never disconnect or bypass any switch.
8. Carbonmonoxide inthe exhaustfumes canbe fatalwhen inhaled,never operatea machinewithout proper
ventilation.
9. Fuel is highly flammable, handle with care.
10. Keep engine clean.Allow the engine to cool before storing and always remove the ignition key.
11. Disengagealldrives and set parkbrake beforestarting theengine.
12. Never use your hands to search foroil leaks. Hydraulic fluid under pressure canpenetrate the skin and
cause serious injury.
13. This machine demandsyour attention.Toprevent loss of control ortipping of thevehicle:
A. Use extra caution in backing up the vehicle. Ensure area is clear.
B. Do not stop or start suddenly on any slope.
C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D. Stay alert for holes in the terrain and other hidden hazards.
14. Beforeleaving operator’s position:
A. Disengagealldrives.
B. Set park brake.
C. Shut engineoffand remove the ignitionkey.
D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of body
awayfrommoving parts.
15. Keep hands, feetand clothing away from moving parts. Wait for all movement to stop before you clean,
adjustor service the machine.
16. Keep the areaof operation clear of allbystanders.
17. Stopengine before making repairs/adjustmentsor checking/adding oil to the crankcase.
18. Use parts and materials supplied by only. Do not modify any function or part.
19. Use caution when booms are down as they extend out beyond the center line of the machine.
20. The tank is a confined space, take precaution.
These machines are intended for professional maintenance on golf courses, sports turf, and any other
area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is
expressed or implied.

7
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SAFESPRAYINGPRACTICES
Personsengaged in the handling, preparation or application ofchemicals must followaccepted practices to
insurethe safety of themselves andothers,
1. WEAR protectiveclothing including:gloves, hat,respirator, eye protection andskin coveringsuitablefor
protectionfrom chemicalsbeing used.
2. BATHE thoroughlyafter any exposure to chemicals, giving particularattention toeyes, nose, earsand
mouth.
3. CLEAN equipmentand materials in accordance withemployer, municipaland stateregulations.Use only
approvedareasanddrains.
4. DISPOSE ofchemicals and rinse solutions byapproved and legalmeans.
5. PROVIDE methodsand materials for operators towash eyes andhands immediately during the spraying
process.
6. PROVIDE methodsand materials for control, safedilution and neutralizationof chemical spills during
preparation,spraying,transporting andcleanup.
7. Always check and follow the directions and safety warnings of the chemicals to be used.
8. Securethe discharge lines before starting the pump.An unsecured discharge line may whip.
9. Periodically inspect the pump and the system components.
10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight and
secure.
11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.
12. Use only pipe,hose and fittings rated formaximum pressure orpressure at whichpressure relief valve is
set at. When replacing pipe, hose or fittings, use new product.
13. Do not operate an engine in an enclosed area. Be sure the area is well ventilated.
14. Do not usethese pumps for pumping water or other liquidsfor human oranimal consumption.
15. Do not pump flammable or explosive fluids such as gasoline,
fuel oil, kerosene, etc.
Do not use in explosive atmospheres. The pump should be used
only with liquids compatible with the pump component materials.
16. Be sure allexposed movingparts are guarded and thatall coupling devices are securelyattached before
applyingpower.
17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids
from the system and flush.
18. Protect pump fromfreezing conditionsby draining liquid and pumpingrust inhibitingantifreeze solution
through the system, coating the pump interior.
19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam system, if booms
areraised in transit they canfall forward or backward whencoming to a stop orwhile traveling onuneven
terrain.
Readand understand this manual and all safety signs before operating and maintaining. Review the safety
instructionsand precautions annually.
TAKE NOTE! THIS SAFETYALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL
YOURATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONALSAFETYAND THE SAFETY OF
OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURYOR DEATH.

8
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SPECIFICATIONS
WEIGHTSANDDIMENSIONS
Length 128"(325 cm)
Width 72"(183 cm)
Heightw/ ROPS 84" (213 cm)
Heightw/ BoomsFolded 136" (345 cm)
Wheel Base 68" (173 cm)
Weight Empty 2340lbs (1061kg)
Weight Full 4950lbs (2245kg)
SOUNDLEVEL(DBA)
At earlevel 88.4 dBA
At 30 ft. (9.14 m) 77 dBA
ENGINE
Make Kubota
Model# V1505
Type / Spec# 1G994-0000
Horsepower 35.5 hp (26.6 kW)
Fuel(EMISSIONS) No.1-D or No. 2-D, S500: Low Sulfur Diesel (LSD) less than 500 ppm or 0.05 wt.%
No1-D or No.2-D, S15: Ultra Low Sulfur Diesel (ULSD) less than 15 ppm or 0.0015 wt.%
CoolingSystem LiquidCooled
LubricationSystem Full Pressure
Alternator 15Amp
WHEELS&TIRE Front: Two 20 x 11.00 x 10Turf; 20 psi (1.4 bar)
Rear: Two 29 x 14.00 x 15 Multi-Trac; 30 psi (2.0 bar)
SPEED
Infinitely Variable 0-10 m.p.h. (0-18 kph)
BATTERY Automotivetype 24F- 12 volt
BCIGroup Size 24
ColdCrankingAmps 900minimum
GroundTerminalPolarity Negative(-)
MaximumLength 10.25" (26cm)
Maximum Width 6.88" (17 cm)
MaximumHeight 10" (25 cm)
FLUIDCAPACITY
CrankcaseOil See Engine Manual
Fuel 7 gallon(26.5 liters)
HydraulicFluid 10 gallon (37.8 liters)
Grade of Hydraulic Fluid SAE 10W-40API Service SJ or higher Motor Oil
Radiator 1.06gallons
OPTIONALEQUIPMENT
15-618 Water Meter Kit 30-009 ManualHose Reel
17-585 18' HD Super Boom 30-010 ElectricHoseReel
17-580 20' HD Super Boom 30-004 FoamMarker
30-006 FreshWaterTank 15-835 TankRinse System
30-007 Chemical Cleanload Safe Fill 15-850 SunshadeCanopy
31-006 AllWeatherTop
17-590 Lazer-BeamAuto Boom for HD Booms

9
Introduction
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
SETUP
The Spray Star 3180 arrives from Smithco setup and ready for service. Depending on freight conditions battery installed.
The spray system is normally shipped attached to the 3180 Prime Mover. If a spray system is to be fitted to a Prime
Mover by a dealer or factory, assemble and attach the components in accordance with the parts drawings in the Spray
Star 3180 Parts/Service Manual.
1. Check the tire pressure. The front tires are 20 psi (1.4 bar) and
rear tires are 30 psi (2.0 bar).
2. Battery is located under seat. This is a negative grounding
system.
Connecting battery cables to the wrong
post could result in personal injury and/
or damage to the electrical system.
Make sure battery and cables do not
interfere or rub on any moving part.
Connect red positive (+) cable (A) to battery first. When
disconnecting remove black negative (-) cable (B) first.
3. Check hydraulic fluid level in tank located under the seat.
Remove cap and add SAE 10W-40 API Service SJ or higher
motor oil if necessary. Fluid level should be about 2-21/2" (5-6.4
cm) from the top of the tank when cold. DO NOT OVERFILL.
4. Fill fuel tank, located on right side, with No. 2 diesel
Fuel is flammable, caution must be used when storing or handling it. Do not fill fuel tank
while engine is running or an enclosed area, fumes are explosive and dangerous to
inhale.DO NOT SMOKEwhile fillingthe fuel tank.DO NOTOVERFILL
5. Machine should be greased before starting, refer to Spray Star 3180 Parts/Service Manual for location.
6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with instructions in
the Spray Star 3180 Parts/Service Manual. The nozzles must be the correct distance above the turf as described
in Turf Spraying Guide. The spray boom must operate properly and the outer sections must break away safely if
an object is struck by them, they must then return to normal operation position.
7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.
8. Machine is shipped with windshield washer fluid in to prevent freezing. Flush system completely with clear water.
Fill tank with water and retighten the four bolts used to hold the tank in place.
9. Read operating instructions before starting.
Never allow pump to run dry! The valve on the suction side of the pump (between the
pump and tank) must be fully open whenever the pump is operated.
FUEL
CHECKEMISSIONREGULATIONSOFYOURAREA
With Emission control now in effect diesel fuel specification type and sulfur content % (ppm) used must be in compliant
with all applicable emission regulations for the area in which the engine is operated.
Use of diesel fuel with sulfur content less than 0.10% (1000 ppm) is strongly recommended.
If high sulfur fuel is used, change oil and oil filters twice as often.
DO NOT USE Fuels that have sulfur content greater than 1.0% (10000 ppm).
Diesel fuels specified in EN 590 or ASTM D975 are recommended.
Since KUBOTA diesel engines of less than 56kW (75 hp) utilize EPA Tire 4 and Interim Tier 4 Standards, the use of low
sulfur fuel or ultra low sulfur fuel is mandatory for these engines, when operated in US EPA regulated areas. Therefore,
use No.2-D S500 or S15 diesel fuel as a alternative toe No. 2-D for ambient temperatures below -10°C (14° F).
SAFETY SIGNAL WORDS

10
Operation
PARTSMANUALSAVAILABLEONLINEATsmithco.com
CONTROLS&INSTRUMENTS
A. HourMeter -The hour meter indicates hoursof machine operation. It operatesonly when the ignition
switch is on.
B. Glow Plug - When ignition is turned on, glow plug lights when ready to start.
C. WaterTemperature Light -Temperaturelight will comeon when the engine startsto overheat.
D. Ignition Switch - The ignition switch has three positions: Off - Run - Start.
E. TiltSteering - Hold lever down and adjuststeering wheelto desiredposition andrelease lever.
F. Oil Light - The oil light should come on when the ignition is on without the engine running and go out when
the engine is running. The oil light will light when the oil pressure is low. If oil light should come on, shut
engineoff immediatelyand find the cause.
G. Speedometer -The Speedometer indicates ground speed ofthe vehiclein miles per hour andkilometers
perhour.
H. Lights - This rocker switch turns lights on by pushing on the top and off by pushing on the bottom.
I. Ground Speed (Cruise) Control - This rocker switch initiates cruise control by pushing on the top and
turning it off by pushing on the bottom. Works with ground Speed Control Foot switch.
J. Buzzer - The buzzer sounds if the pump is running dry.
K. Spray Pump - This rocker switch turns the spray pump on by pushing on the
top and off by pushing on the bottom.
L. Left Boom Switch - This rocker switch lifts and lowers the left boom.
M. Right Boom Switch - This rocker switch lifts and lowers the right boom.
N. Hand Throttle - The hand throttle is used toregulate engine speed.
O. CupHolder- Holds standard cup.
P. Spray Boss Control - Engages and disengages speedboss. Forward is
engage and all the way back is disengage. When the lever is engaged it sets
a stop for the accelerator. The accelerator pedal must be used to maintain
this speed. To adjust speed use the knob on the end of the lever, counter
clockwise increases speed and clockwise decreases speed. Disengage the
leverand you willhave fullaccelerator pedal range.
Q. Park Brake Toggle Switch - This toggle switch will engage park brake. Lift
togglecoverand moveswitch forward.DO NOT ENGAGE WHILE IN MO-
TION.

11
Operation
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
CONTROLS&INSTRUMENTS
R. Ground Speed (Cruise) Control Foot Switch - When rocker switch is turned on and desired speed is
obtained, push foot speed control switch to set cruise. (see below).
S. Master Boom Switch - located on the left floorboard is used to override the master switch on the com-
puter console of the spray systems. By pushing down it will turn on/off the booms. For the 440 System
only the Master Switch on the computer must be off for the master boom control switch to work.
T. Accelerator Pedal - This pedal controls ground speed. Press pedal to increase speed. Varying the
amountof movementof the pedal will vary the ground speed.
U. ReversePedal - This pedalcontrols reverse.Press pedalto movemachine inreverse.
GROUNDSPEEDCONTROL
Theground speedcontrol does not work the
sameas anautomotive type cruise. The ground
speedcontrol is located on thecenter floorboard
and is used to lock forward speed.
TOENGAGE:
1. Flip rocker switch ‘On’ (green light).
2. Obtaindesired speedwith footpedal.
3. Step on foot switch to lock speed.
4. Push foot switch again to disengage.
To avoid abrupt
stop, place foot on
traction pedal
before disengaging
speed control.
TOWING
When it is necessary to move the Spray Star 3180 without the engine running, there are 2 things that need to be
done. First, the bypass valve built into hydrostatic pump must be "open" by turning it 1/4turn to open. The valve
is located on the back side of the pump.An "open" valve allows fluid to pass through the wheels freely. When
normaldriven operation is desired, valveshould be "closed"by turning it clockwise. Failureto "close" the valve
withengine running means no powerto wheels. Secondly, the handbrake needs tobe manually released.The
hand brake is located under the engine. To manually release the brake you must loosen the locknut and screw
in the stem to the bottom. Tighten the lock nut and pump handle until hard.
MANUALBRAKEHANDPUMPMANIFOLD
The hand brake is located under the engine. The hand brake is connected to he seat switch and automatically
engages when operator gets up from the seat. So when machine is not
beingdriven, the machine is locked down. If engineis not runningor
you are towing the machine you will have to manually release the
brake. To manually release the brake you must loosen the locknut
and screw in the stem to the bottom. Tighten the lock nut and pump
handleuntil hard.
Run machine at half-throttle minimum, prior to operating trac-
tion pedal. This will ensure proper brake release.

12
Operation
PARTSMANUALSAVAILABLEONLINEATsmithco.com
OPERATION
Beforeoperating the Spray Star3180, become familiar with all controls and functions.Also complete all mainte-
nancerequirements and read allsafety warnings. Knowing the Spray Star3180 thoroughly, howit operates, and
by doing the prescribed maintenance steps, you can expect trouble free operation for years to come.
SAFETY
Operatorneeds toalways be the concern ofan operator of a movingvehicle orany machine withmoving parts.
1. Keep all shields and guards in place.
2. Keepthe parkingbrake engagedany time the operator isaway fromthe vehicleor whenever service is
performed.
3. Alwayswear thenecessary protective clothing and equipment.
4. Turn engineoffwhenrefueling orperformingmaintenance notspecificallyrequiring enginepower.
DAILYCHECKLIST
1. Checkthe engineoil level. Add as needed. DO NOT OVERFILL.Refer to engine owner's manualfor oil
gradeandprocedure.
2. Tire pressure should be 20 psi (1.4 bar) on front and 30 psi (2.0 bar) on back.
3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any faulty
equipmentor tighten if loose.
4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.
5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.
6. Checkthe hydraulicfluid level. Thehydraulic fluid tankis located underthe seat. Thefluid level shouldbe
2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40API Service SJ or higher
Motor Oil.
7. Inspectthe steering, throttleand shift linkages for good hookups and
cleartravel.
8. Checkcontrols forsmooth, properworking operation. Lubricateas
needed.
9. Checkanti-vibrationmounts onengine frame.
STARTINGTHEENGINE
1. Makesure bothfuel flow valves are ‘On’.They arelocated on the fuel
tank.
2. The ignition switch is located on the dashboard. Insert the key (A) and
turn clockwise to (B). When glow plug light goes off Turn key to (C) un-
til the engine starts. Release the key and it will return to the run posi-
tion (B).
3. Allowengine toidle and warm up beforeselecting directionof travel.
STOPPINGTHEENGINE If the engine has been running under high power, let it run at slow idle speed a
few minutes to cool the engine down, before turning the ignition switch to the
OFF position.
1. Disengagespraypump.
2. Movethe throttlelever to “slow”and turn ignitionkey to the“off” position.
3. Removethe ignitionkey and engage the parkbrake.
Never leave the vehicle unattended with the engine running. Always bring the
vehicle to a complete stop, engage park brake, turn key off and remove key.

13
Operation
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
OPERATION
Run machine at half-throttle minimum, prior to operating traction pedal. This
will ensure proper brake release.
Before using the Spray Star, the operator and spray technician must familiarize themselves with all of the information on
chemical spraying contained in the Turf Spray Guide.
All testing and calibrating of sprayers is to be done with water, not chemicals. This insures the safety to all involved in
performing the calibration operation. Only after all calibration procedures are completed should chemical be added to
the sprayer.
HILLSIDE OPERATION
Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate on
slopes greater than 10°.
BATTERY
Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any ig-
nited object to come near the battery. When charging or working near battery, always shield your eyes and always pro-
vide proper ventilation.
Battery cable should be disconnected before using “Fast Charge”.
Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If
electrolyte starts boiling over, decrease charging.
Always remove grounded (-) battery clamp first and replace it last. Avoid hazards by:
1. Filling batteries in well-ventilated areas.
2. Wear eye protection and rubber gloves.
3. Avoid breathing fumes when electrolyte is added.
4. Avoid spilling or dripping electrolyte.
Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte is
splashed on any part of your body, flush all contact areas immediately with liberal
amounts of water. Get medical attention immediately.
JUMP STARTING
Use of booster battery and jumper
cables. Particular care should be
used when connecting a booster
battery. Use proper polarity in order
to prevent sparks.
To jump start (negative grounded battery):
1. Shield eyes.
2. Connect ends of one cable to positive (+) terminals of each
battery, first (A) then (B).
3. Connect one end of other cable to negative (-) terminal of "good" battery (C).
4. Connect other end of cable (D) to engine block on unit being started (NOT to negative (-) terminal of battery)
To prevent damage to other electrical components on unit being started, make certain that engine is at idle speed
before disconnecting jumper cables.

14
Operation
PARTSMANUALSAVAILABLEONLINEATsmithco.com
OPERATION (CONTINUED)
SPRAYERVALVESETTINGSANDSPRAYTANKAGITATION
The3-way valve on the suction side of the pump, between the tank andthe pump must be open before pump is
engaged. Close this valve only when necessary to clean the filter with spray material in the spray tank.
Thereis one manual flow controlvalve on the discharge sideof the spraysystem. This valve controls theagita-
tor.This valve may beopened asmuch as necessary to providehydraulic agitationthroughthe quadrajet agitator
inthe tank bottom.This valve maybe partially closedto prevent or reduce foam buildup from the spray materials
inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25 gallons (3.8-95 Li-
ters) depending on terrain and other conditions) it may be necessary to close the valve in the agitator line in
orderto prevent loss of suctionprime.
If your Spray Star is fitted with a hose reel, there is a second ball valve on the discharge system to supply mate-
rial to the hose reel.
The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable
orifice discs which discharge the following amounts of spay material.
Input to Input to Agitator Agitator Agitator Agitator
Nozzle Agitator Agitator Pressure Pressure Output Output
Diameter in gpm in L/min in psi in bar in gpm in L/min
1/8" 1.9 7.2 25 1.7 6.3 23.8
1/8" 2.7 10.2 50 3.4 10.0 37.9
1/8" 3.8 14.4 100 6.9 15.0 56.8
5/32" 2.8 10.6 25 1.7 7.6 28.8
5/32" 4.2 15.9 50 3.4 12.2 46.2
5/32" 5.5 20.8 100 6.9 17.5 66.2
3/16" 3.6 13.6 25 1.7 9.1 34.4
3/16" 5.6 21.2 50 33.4 14.3 54.1
3/16" 7.9 29.9 100 6.9 18.7 70.8
You can change orifice disc sizes to enhance spray system performance. Smaller discs reduce amount of agita-
tion (desirable in some foaming materials) and make more dischargeable liquid available for nozzles. Larger (or
none) discs increase amount of agitation and make less dischargeable liquid available for nozzles.
ENVIZIOPROIIDO'SANDDON'TS
DO’S ANDDON’TS
Do havethe serialnumber and firmware revision availablewhen calling for technical assistance.It isbest if
the user is in the machine and in front of the field computer when calling for support.
Do reviewthe manualin itsentirety beforeoperating thefield computer.
Do turn machine on prior to starting Envizio Pro II. Voltage spikes can cause damage to computer.
Don't letwater onor nearEnvizio ProII Computer.
Don’t turnthe fieldcomputer offwithoutproperly closing any open jobsand powering down the computer. If
the field computer loses power during a job, information within the job files may be lost and the associated
filesmay become corrupt.
Do powerdown Envizioprior toshutting offmachine.
Don’t use sharp objects or harsh chemicals on the field computer touch screen as they may damage the
display.Console Features
Do removeEnvizio ProII during cold weather. Cold weather will causethe batteryto drain.
EnvizioPro II comes with aQuick Reference Guideand an Installation & OperationManual. Please read
thesemanuals beforeoperation. Manuals can be downloaded offtheinternet at www.ravenprecision.com
andoffthe www.smithco.com website under PartsandTechnical Information.

15
Operation
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
ENVIZIOPROII-SHARPSHOOTER-RATESYNC FEATURES
INITALSETUP
To Begin a Job & Create a Spray Zone
Turn Sharpshooter w/RateSync On
Press Auto/Manual button to Auto
PSI is preset. Use arrow buttons to increase/decrease
POWER
Home
Screen
SwitchPro
AccuBoom
Switches
Master
ON/OFF
Increase/Decrease
Flow
GPSGreen-Signal
Yellow-LowSignal
Red - No Signal
POWER
Auto/Manual
Button

16
Operation
PARTSMANUALSAVAILABLEONLINEATsmithco.com
INITIALSETUP
1. Turn Raven Envizio Pro Controller On 2. Check to Insure GPS Icon is Green
Hold Blue Switch until screen lights up. Touchthe GreenArrow toenterJobMenu
Wait until Home ScreenAppears (see right) where you can Start a New Job
3. New Job Menu 4. Start a New Job Screen.
Insure ArrowonTractoris Forward Touch the Yellow New Job Box
Touch Iconto Correct if Needed (Thiswill bring upthe Keyboard Screen)
Touch the Blue “Job” Box to Start a New Job
5. Name the Job
This can be as elaborate or as simple as you like.
Examples: SouthCourse Fairway No. 4
Or SF4
Touch theGreen “Check” Circle
Touch the Blue “Pattern” Box
(This Will Bring Up Your Next Pass Options)
Select “Last Pass” A – B

17
Operation
PARTSMANUALSAVAILABLE ONLINEATsmithco.com
INITIALSETUP
6. Touch the “AccuBoom” Blue Box 7. Touch to Check “Use Spray Zone Map”
8. Touch the Yellow New “Field Boundary Map” 9. This will bring up the Keyboard Screen
Again,Name the New FieldBoundary Map;
it’s best to use the same name as the New
Jobfile. Touchthe Green “Check” Circle
This will return you to the Job “AsApplied” Screen
10. Creating a Field Boundary
Drive to the area where you want to start your Spray Zone. Press the Green “Menu” Box in the Lower
Right Corner To Bring Up the Tools Menu Along the Right Side
Press the Black “Boundary Tools” Box
Touchthe Black“RecordField Boundary”Box

18
Operation
PARTSMANUALSAVAILABLEONLINEATsmithco.com
INITIALSETUP
11. Select One of the Options Below to Create the Field Boundary
12. This will Enable the On screen MappingTools
Stop” & “Pause”
13. Screen with Field BoundaryTools on Screen
14. Drive the Outline of theArea. You will see the Yellow Line that will be the boundary of the
Field Boundary located at your selection point. Press the Black “Pause” Box at any time
toManeuver the Sprayertocreate aSquare Corner
15. Press the Black “Stop” Box when at the End of the Area You Want to Map. The Envizio
Pro will Draw a Straight Line to Point where Recording Began to Close the Spray Zone