Smiths Medical CADD-MS 3 User manual

s
Operator’s Manual
CADD-MS™ 3 Ambulatory Infusion Pump
Model 7400
This online version differs from the printed version.
Certain information that is not intended for patients has been removed.

Updates to the manual
e following updates were made to this version
(40-5470-51C) of the User Manual. e specic pages
aected by the changes are shown.
For your safety, review the manual carefully, including
all warnings and cautions. If you don’t understand
something, contact your clinician, your pump provider,
or Smiths Medical.
Summary of updates Pages
Warning regarding
tightening the battery cap
3, 10, 16, 62, 80
Inspecting the battery cap 17, 80
Added illustrations 9,17, 80
WEEE Warning 16, 81
WEEE Statement 81

i
is manual provides information on programming,
using and maintaining the CADD-MS™3 Ambulatory
Infusion Pump. is manual is intended for clinicians
only. DO NOT permit patients to have access to this
manual. DO NOT disclose the pump’s security pass
codes or any other information that would allow
inappropriate access to programming and operating
functions.
e issue date of this manual is included on the back
cover. If your manual is a year or more old, contact
Smiths Medical MD, Inc. (or check the web site at
www.smiths-medical.com) to see if a newer manual is
available.
If you have comments,
questions, or problems...
If you have comments or questions about the pump,
please call the appropriate number given below. You will
be asked for the pump’s serial number, which you will
nd on the back of the pump.
Our sta is available to help you 24 hours a day with
programming and operation of the pump.
U.S. Distribution
Smiths Medical MD, Inc.
St. Paul, MN 55112 USA
1 800.426.2448 (USA)
1 651.633.2556
www.smiths-medical.com
Smiths Medical International Ltd.
WD24 4LG UK
[phone]
@

ii
Table of contents
Important Information
Important safety information ............................................................1
Warnings.......................................................................................1
Cautions........................................................................................3
Explanation of symbols.......................................................................4
Introduction.........................................................................................6
Indications..............................................................................6
Contraindications..................................................................6
Delivery features ..........................................................................6
Continuous Rate ....................................................................6
Doses .......................................................................................6
Other features.........................................................................6
Glossary of Terms................................................................................7
Programming the Pump
Pump illustrations ...............................................................................9
Description of features and buttons................................................10
Battery cap with o-ring .......................................................10
Display ..................................................................................10
Programming keys ..............................................................10
and keys..................................................................10
Demand Dose button .........................................................10
Cartridge cap .......................................................................10
Infrared (IR) windows ........................................................10
Features.......................................................................................11
Vibration alert .....................................................................11
Occlusion (blockage) sensor .............................................11
Cartridge sensor ..................................................................11
Watertight ............................................................................11
History .................................................................................11
Description of pump display and menus .......................................12
Screensaver and backlight ........................................................13
Menus....................................................................................13
Editing values.......................................................................13
Timeout feature....................................................................13
Home screen example.........................................................14
Sample screens .....................................................................14
Accessories .........................................................................................15
Cartridge...............................................................................15
Infusion sets .........................................................................15
Before using the pump for the rst time ........................................16
Insert a battery ...........................................................................16
Self Tests......................................................................................18
Setup....................................................................................................19
Opening the Setup Menu .........................................................20
Setup Menu - Time and Date...................................................21
Setup Menu - Local Formats ...................................................22
Setup Menu - Alerts ..................................................................23
Setup Menu - New Patient........................................................25
Setup Menu - Delivery..............................................................26
Setup Menu - Security...............................................................28
Delivery Program ..............................................................................29
Using the Pump
Loading a cartridge ...........................................................................31
Supplies required .................................................................31
1. Filling the cartridge.........................................................31

iii
2. Attaching an infusion or extension set
and loading a lled cartridge into the pump .................32
3. Fill the tubing...................................................................36
4. Fill cannula.......................................................................37
5. Set site change reminder and restart delivery..............38
Stopping and starting the pump......................................................39
Starting the pump......................................................................40
Delivering a Demand Dose..............................................................41
Canceling doses .................................................................................42
Canceling a dose (Demand or Automatic)
while in progress................................................................43
Canceling next Automatic Dose .............................................43
History ................................................................................................44
Beep or Vibrate ..................................................................................46
Continuous Rate Menu.............................................................47
Automatic Dose Menu..............................................................48
Demand Dose Menu .................................................................49
Help
About alarms (Beep/Vibrate settings) ............................................51
Troubleshooting.................................................................................52
Alarms...................................................................................52
Alerts .....................................................................................54
Other messages ....................................................................55
Cleaning the pump............................................................................59
Servicing the pump ...........................................................................60
e pump and:...................................................................................61
Extreme temperatures ..............................................................61
Water ...........................................................................................61
If the pump is dropped or hit hard.................................................61
Technical Information
Pump development standards .........................................................63
Specications......................................................................................69
General specications (nominal) ............................................69
Delivery specications......................................................................71
Main Menu ...........................................................................71
Setup......................................................................................71
Delivery Program ................................................................72
Load ......................................................................................72
History ..................................................................................73
Accuracy test results..........................................................................74
Safety features and fault detection...................................................76
Hardware safety features...........................................................76
Watchdog timer circuit.............................................................76
Motor drive/motor watchdog circuit .....................................76
Voltage detector circuit.............................................................77
Soware safety features.....................................................................77
Hardware-related soware safety features .............................77
Program memory check ...........................................................77
RAM memory check...........................................................77
Motor circuit check .............................................................78
Keypad encoder check ........................................................78
Data handling and soware safety features....................................78
Data stored in RAM ..................................................................78
Data stored in NOVRAM.........................................................78
Data used in calculations..........................................................79
Timer data registers ..................................................................79
Inspecting the pump .........................................................................80

iv
Collect Separately ..............................................................................81
Limited Warranty .............................................................................82
Index ...................................................................................................84

Important Information
1
Important safety information
WARNING: Read this entire manual before using the
CADD-MS™3 Ambulatory Infusion Pump. If you
do not understand something or have any questions,
contact Smiths Medical MD, Inc. Incorrect use of this
pump, failure to follow the instructions and important
information contained in this manual, or improper/
inadequate troubleshooting can lead to death or serious
injury. Warnings, cautions and other important safety
information can be found in this section, and in bullet form
throughout the manual (indicated by the symbol). e
Help section (starting on page 51) contains information on
troubleshooting the pump and other important information.
Warnings
is manual is designed for clinicians and contains all
of the information needed to fully program the pump.
Do not give this manual to patients as it would allow them
complete access to all programming information.
e CADD-MS™3 Ambulatory Infusion Pump is
designed for subcutaneous, intravenous, epidural and
intrathecal infusion of medication. DO NOT use with
blood or cellular blood products. Use the pump only as
instructed in this manual.
is manual describes how to use and troubleshoot the
CADD-MS™3 pump. Smiths Medical MD, Inc. does not,
however, make any recommendations about any specic
programming related to any therapy. Whether certain
features are appropriate for an individual patient must be
determined before use. Before using the pump, the patient
must receive appropriate training in all its functions and in
troubleshooting problems.
To avoid a risk of explosion, do not use the pump in the
presence of ammable anesthetics or explosive gases.
System delivery inaccuracies may occur as a result of
backpressure or uid resistance, which depends upon drug
viscosity, catheter size, and extension set tubing.
e CADD-MS™ 3 pump and accessories include small
component pieces that could pose a choking hazard to
small children.
Before going to bed, the patient should make sure the
cartridge contains enough medication to last through
the night. Do not use the Vibrate alarm at night. If the
patient is a very deep sleeper, they may want to set the audio
volume to High (the loudest setting) before going to bed.
ere are potential health hazards associated with improper
disposal of batteries, electronics, and contaminated (used)
infusion sets and cartridges. Dispose of used batteries, infu-
sion sets, cartridges, and other used accessories, or a pump that
has reached the end of its useful life, in an environmentally safe
manner, and according to any regulations that may apply.

Important Information 2
If there are any system problems during the self tests,
the pump will stop the tests and display an alarm screen
letting you know there is a problem. If this happens, do
not use the pump.
e cartridge cap, battery cap, and luer connections are
not childproof. Tampering with them can result in over-
or under-delivery of medication.
e time and date must be set correctly, since delivery
factors are time-based, and all history is stored based on
time and date. Occasionally the time will need to be reset,
for example, during daylight savings time or to adjust for a
dierent time zone.
Do not allow the patient to learn the pass code. e
pass code allows access to all delivery programming and
security settings.
If you choose not to require pass codes to access the Setup
and Delivery Program menus, the patient will have full
access to all programming and delivery functions.
Always use the pump’s Load feature when starting a new
cartridge. is will assure that the cartridge is properly
loaded and the infusion or extension set is lled with
medication.
Always use aseptic technique, particularly when work-
ing with the cartridge, infusion set, catheter and access
site to minimize the risk of infections.
e CADD-MS™3 pump and cartridge are not a secure
system. Patient must be assessed for appropriateness of
pump usage.
Always read the Instructions For Use provided with the
medication, cartridge, infusion set, and any other acces-
sory used with the CADD-MS™ 3 pump.
To avoid accidentally infusing medication or caus-
ing backow of blood from the access device (or site),
disconnect the tubing from the access device (or site)
before removing a used cartridge or replacing an infu-
sion set. Never use the pump’s Load Cartridge or Fill
Tubing features while tubing is connected to the patient,
or an unintended dose of medication can be delivered.
If not properly tightened, medication could leak from
the cartridge and tubing connections and disrupt
delivery. Signs of leakage can also mean opportunity for
contamination leading to infection.
Never use Fill Tubing when the infusion set is connected
to the body, or an unintended dose could be delivered.
Always remove all air from the cartridge and infusion
set before starting medication delivery. Air bubbles in
the system can slow or stop medication delivery. Check
all connections carefully for leaks, as leakage can slow or
stop medication delivery to the body, and allow an open-
ing for contamination leading to infection.

Important Information
3
You should provide specic training on delivering a dose.
If the pump is dropped or hit against something hard,
always inspect it carefully to make sure it is still working
properly. Make sure the display is working correctly, and
the cartridge, cartridge cap, battery cap and infusion set are
connected correctly. If there is damage to the pump’s outer
shell (cracks, chips), the pump may no longer be watertight.
Make sure that the battery cap is fully tightened to avoid
an interruption in battery power which can cause the
pump to power down and stop the delivery of drug
therapy. A prolonged interruption in the delivery of drug
therapy can result in serious patient injury or death.
If the display has missing or incomplete characters, or
if the pump does not seem to be working correctly, stop
using the pump immediately. Contact Smiths Medical
MD, Inc. for information on servicing the pump.
Cautions
Avoid strong electromagnetic elds, like those present with
Magnetic Resonance Imaging (MRI) and direct x-ray, as
they can aect how the pump works. If you cannot avoid
them, the pump and pouch must be taken o.
Do not expose the pump directly to ultrasound.
Do not use the pump in a hyperbaric chamber as this
may aect how the pump works and may also cause dam-
age to the pump.
Do not use cell phones within six (6) inches (15 cm) of
the pump. Interference with the pump electronics by cell
phones can occur. If a cell phone interferes with the pump,
the pump will generate a System Fault alarm.
To avoid damage when storing the pump, rst remove the
battery and cartridge. Place the pump in the original car-
ton and keep it away from cold, heat, and dampness. Aer
30 days, any pump programming will be lost and you will
need to reprogram it.
e pump may experience problems if operated in condi-
tions where temperatures are lower than 35.6°F (2°C) or
higher than 104°F (40°C), when relative humidity (non-
condensing) exceeds 90%, and when atmospheric pressure
is lower than 10.2 psi (70 kPa) (10,000 feet above sea level)
or higher than 15.4 psi (106 kPa). If you experience prob-
lems, remove the pump from use.
e pump may be damaged if stored in environments
where temperatures are lower than –4°F (–20°C) or higher
than 140°F (60°C), when relative humidity (non-condens-
ing) exceeds 90%, and when atmospheric pressure is lower
than 10.2 psi (70 kPa) (10,000 feet above sea level) or
higher than 15.4 psi (106 kPa).
Do not use NiCd, nickel metal hydride, carbon zinc (heavy
duty), lithium or any rechargeable batteries. ey will not
power the pump properly, and the battery life indicator on
the home screen may not show the correct amount.

Important Information 4
Use only Smiths Medical MD, Inc. 3 ml Medication Car-
tridges; other manufacturers’ products will not work with
the CADD-MS™3 pump.
Never use abrasive cleaners, solvents, bleach, scouring
pads or sharp instruments when cleaning your pump, as
they can scratch, discolor or damage the pump’s outer
shell. If the display is scratched, it may be dicult to read
and you will need to have it replaced. If the outer shell is
chipped or cracked, it may no longer be watertight and
will require service.
Never use steam or very hot water (exceeding 120°F
[49°C]) in an attempt to sterilize the pump. Never
put your pump in the dishwasher. Exposing the pump
to these high temperatures could damage the pump’s
electronics and result in the need to service your pump.
Explanation of symbols
Below is a list of symbols you will see on the CADD-MS™3
pump, packaging, and accessories, as well as explanations of
what the symbols mean.
Serial number
Attention! See instructions for use
Type CF equipment (protection from electric shock)
IPX8 Watertight when submerged to 8 feet (2.4 meters)
for 30 minutes or to 12 feet (3.6 meters) for
3 minutes
Date of manufacture
Use by
On Pump Display: Wait
Caution: Federal (USA) law restricts this device
to sale by or on the order of a physician
Catalog number
Bor AIndicates that the product was designed and
manufactured in accordance with applicable
standards/guidelines and may be sold in the EU
(European Union)

Important Information
5
Appears in pump display, with a message, to indicate
a question you must answer before programming
can continue
Appears in pump display, along with a message, as
an indicator of an alarm condition.
Collect separately
Latex free
Press or keys to move through menu/settings
Top of menu; press key to move through menu
Bottom of menu; press key to move through menu
Approximate volume of medication le in cartridge
Approximate battery life remaining

CR
Continuous Rate home screen

AD
Automatic Dose home screen

DD
Demand Dose home screen

SR
Site Reminder home screen
Empty cartridge or low battery
Keep dry
Fragile, handle with care
Keep away from sunlight
Temperature limitation
Important safety information, warnings and cautions
5Dansk .Français
/Deutsch 0Italiano
8Ελληνικά 3Nederlands
-English 6Norsk
1Español 2Português
7Suomi 4Svenska

Important Information 6
Doses
e pump can deliver two types of doses, an Automatic Dose
(programmed to deliver a specic dose at a preprogrammed
time) as well as Demand Dose (delivered by the patient as
needed). You can also program lockout times so that you can
control the time between doses.
Other features
e pump has a large display (or screen) where all program-
ming, operating and alarm information is displayed. Pro-
gramming of the pump is menu-driven, like an ATM or cell
phone.
e pump is powered by one AAA (IEC LR03) alkaline bat-
tery, which is readily available at most grocery stores, hard-
ware stores, drug stores, and electronic stores. e expected
battery life is approximately 2 weeks (battery low alert) at
0.124 ml/hr.
Caution: Do not use NiCd, nickel metal hydride, carbon
zinc (heavy duty), lithium or any rechargeable batteries.
ey will not power the pump properly, and the battery
life indicator on the home screen may not show the correct
amount.
As long as the pump’s labels and outer shell are intact, the
pump is watertight to a depth of 8 feet (2.4 meters) for
30 minutes or 12 feet (3.6 meters) for 3 minutes.
Introduction
e CADD-MS™3 Ambulatory Infusion Pump provides
measured medication therapy to patients in hospital or out-
patient settings. Any medication therapy must be overseen by
a physician or certied, licensed healthcare professional.
Indications
e CADD-MS™3 pump is a syringe-based ambulatory infu-
sion pump designed for subcutaneous, intravenous, epidural
and intrathecal infusion of medication.
Contraindications
e pump is not indicated for anyone who cannot follow the
instructions for use or perform basic troubleshooting and
maintenance activities associated with ambulatory pump use.
Delivery features
e pump can be used to deliver medication in two ways, as a
continuous rate and as an added dose.
Continuous Rate
e pump can be programmed to deliver a steady ow of
medication called the Continuous Rate. You can program
up to 48 time/rate segments per 24 hour period to meet the
patient’s medication needs throughout the day and night.

Important Information
7
Glossary of Terms
e following is a list of terms used throughout this manual:
Automatic Dose: Automatic Doses are programmed amounts
of medication delivered at specic times of the day.
Continuous Rate: e amount of medication delivered continu-
ously over 24 hours a day, providing delivery of medication
at all times. e continuous rate is measured in milliliters per
hour (ml/hr).
Cannula: A small, so tube or needle, inserted into the body,
through which medication is delivered.
Cartridge: The container that holds the medication. The
Smiths Medical 3 ml Medication Cartridge looks like a small
syringe.
Demand Dose: A Demand Dose is an extra programmed
amount of medication initiated by the patient as needed.
Dose: An extra amount of medication given at specied times
and or as needed.
Fluid path: e areas inside the cartridge and infusion set that
come into direct contact with the medication. ese areas
include the inside of the tubing and connectors, the inside
and tip of the needle and cannula, and the inside and tip of
the cartridge. To help protect against infection, never touch
or blow directly on any part of the uid path.
Pump and delivery history is automatically tracked by the
pump, and can be viewed in the History menu (see page 44).
e pump has a Security feature which allows you to lock out
the Setup and Delivery Program menus. is feature helps
prevent tampering with the programming of the pump.
e pump requires the use of the Smiths Medical 3 ml Medi-
cation Cartridge and an infusion set (any manufacturers’
infusion set can be used, as long as it has a standard luer lock
to connect to the cartridge).

Important Information 8
Infusion pump: A small electromechanical medical device
designed specically for delivering precise amounts of medi-
cation into the body. e CADD-MS™3 pump systems are
controlled by two microprocessors (computer chips) which
continuously monitor each other to make sure the systems
are working properly.
Occlusion: Blockage. Occlusions are associated with the infu-
sion set and/or access site, and mean that medication delivery
is stopped. Blockage can be caused by a number of things,
including the tubing being pinched or kinked, the cannula or
needle being blocked, as well as other reasons.
Pushrod: On the CADD-MS™3 pump, the cartridge is attached
to the pushrod and, when the pump is started, the motor causes
the pushrod to move forward and push medication through
the infusion set into the body.

Programming the Pump
9
Pump illustrations
Figure 1 Figure 2
$"%%.4
Cartridge
viewing
window
IR windows
(not used
on this
model
pump)
Display
Demand
Dose
button
Cartridge
cap
Down key
(backlight)
Right program key
Left
program
key
Battery cap
Up key
O-ring

Programming the Pump 10
Description of features and
buttons
Battery cap with o-ring (Figure 1)
Holds the battery in place in the battery compartment.
e pump uses one AAA (IEC LR03) alkaline battery.
e approximate amount of battery life is displayed in
the home screen, and an alarm is given when battery
power is low. Keep extra batteries on hand.

Warning: Make sure that the battery cap is fully
tightened to avoid an interruption in battery power
which can cause the pump to power down and stop
the delivery of drug therapy. A prolonged interrup-
tion in the delivery of drug therapy can result in
serious patient injury or death.
Display (Figure 1)
e display (also referred to as the screen) shows all the
programming, operating and alarm/alert information
for the pump.
Programming keys (Figure 1)
ere are two keys on the front of the pump right below
the display that do not have any names or symbols on
them. ese are the programming keys. ey have dier-
ent functions, depending on where you are in a menu. In
the display right above each key is a short description of
what happens if you press it. (Always look to the display
above each key to see what the key is used for.)
and keys (Figure 1)
e and keys are used to move around in menus,
and to program amounts. Whenever you can use the up
and down keys, the symbol is shown in the bottom,
middle part of the display. When you are at the top or
bottom of a menu, only one of the keys can be used, and
the symbol will change to or , respectively.
Demand Dose button (Figure 1)
If Demand Doses are allowed, the user can press the
Demand Dose button to initiate a dose.
Cartridge cap (Figure 1)
Once you load a lled cartridge into the compartment,
press and turn the cartridge cap over the top of it to hold
it rmly in place. You can look at the cartridge viewing
window (Figure 2) to make sure the cartridge is properly
loaded, and to periodically check the amount of medica-
tion le in the cartridge.
Infrared (IR) windows (Figure 2)
e IR windows allow the pump to communicate with
a PC or other IR accessory. ere is no IR functional
capability available with this model pump.

Programming the Pump
11
Features
Vibration alert
If you don’t want the pump to beep during alarms and
alerts, you can program it to vibrate instead. is feature
can be used in meetings, classrooms, etc. If you choose
Vibrate, the “beep” that accompanies each key press is
also disabled. e battery is used much more quickly
when you use Vibrate.
Occlusion (blockage) sensor
e occlusion sensor continuously tests for blockage that
prevents medication from being delivered.
Cartridge sensor
ere is a sensor in the cartridge chamber that has two
functions. It senses when a cartridge is correctly loaded in
the chamber. If the cartridge becomes loose or detached
during use, the sensor causes an alarm to occur. When
you load a new cartridge into the pump, the sensor also
measures how much medication is in the cartridge, and
displays this information in the upper le part of the
home screen.
Watertight
As long as the pump’s labels and outer shell are intact the
CADD-MS™3 pump is watertight to a depth of 8 feet
(2.4 meters) for 30 minutes or 12 feet (3.6 meters) for
3 minutes.
History
e pump has a History feature that displays a variety of
delivery history information.

Programming the Pump 12
• e Automatic Dose (AD) home screen
shows when the next automatic dose is
scheduled to be delivered. This home
screen is only visible if Automatic Dose is
set to Yes (in use) in both the Setup and
Delivery Program menus. You can also
access the Automatic Dose menu from this home screen
(see page 48). When an Automatic Dose is being delivered,
the screen will show, “Auto Dose Active”.
• e Demand Dose (DD) home screen
shows the amount, time, and date of the
last demand dose programmed. is home
screen is only visible if Demand Dose is set
to Yes (in use) in both the Setup and Deliv-
ery Program menus. You can also access the
Demand Dose menu from this home screen (see page 49).
When a Demand Dose is being delivered the screen will
show, “Demand Dose Active”.
• e Site Reminder (SR) home screen
shows the date and time of your next pro-
grammed site reminder alert. is home
screen will only be visible if set to Yes (in
use) in the Setup / Alerts menu. If you
haven’t programmed another site reminder,
it shows when the previous one occurred.
Description of pump display
and menus
All programming, operating and alarm/alert information
is shown in the display. Programming of the pump is menu
driven, like a cell phone or ATM.
e Home screen shows various infor-
mation relating to pump operation. If all
of the delivery types are turned o, the
home screen at right is shown. Depending
on which features you are using, one or
more of the following home screens will
be shown:
• e Continuous Rate (CR) home screen
shows the current continuous rate being
delivered. is home screen will only be
visible if Continuous Rate is set to Ye s
(in use) in both the Setup and Delivery
Program menus. You can also access the
Continuous Rate menu from this home
screen (see page 47).
16
Menu>
10/02/05 04:30 PM
PUMP STOPPED
2.988ml ##
16

CR Menu Menu>
Continuous Rate
0.242 ml/hr
2.988ml ##
CR
16

AD Menu Menu>
Next Auto Dose:
12:00 AM 0.05 ml
2.988ml ##
AD
16

DD Menu Menu>
Last Demand Dose:
03:02 PM 10/02/05
0.03 ml
2.988ml ##
DD
16

<Stop Menu>
Next Site Reminder
10/02/05 at
04:30 PM
2.988ml ##
SR

Programming the Pump
13
A variety of symbols appear on the screen. For example,
any time you have to answer a question before proceed-
ing, the question appears on the screen accompanied
by . Alarms and alerts are accompanied by .If the
pump is performing a task which takes a little time, you
will see .
Screensaver and backlight
e screensaver allows the pump to save on battery power.
When you are at the home screen and no
keys or buttons are pressed for 15 sec-
onds, the screensaver display appears. e
screensaver shows the time and whether
the pump is running or stopped. Press
any key on the keypad to deactivate the
screensaver and return to the home screen.
Pressing the key turns on the screen
backlight; the backlight automatically turns o when the
screensaver reactivates. You can only turn on the backlight
from screensaver. When the motor is running, the backlight
blinks.
Menus
To choose a menu item, press the or key to high-
light the item you want, then press Select.
Editing values
Screens with a single eld: press the or key to
change a value, then press the < or > key to save it or
continue editing or move to another screen.
Screens with more than one eld: press the > key (Next)
to move to the eld you want to change, and then press
the or key to change the value. On some screens
pressing the < key (Done) will save your changes and
move to another screen. On others, pressing the < key
(Back) will save the value in the eld and move to the
previous eld on the screen. ere are two exceptions:
1) where your changes take eect only when you exit the
screen, and 2) the New Patient Screen and the Enable
Delivery Methods screen.

Warning: Because the method of saving values
varies by screen, it is essential that you review the
program before beginning delivery.
Timeout feature
If you change a value using the or key and
then decide you don’t want to change it aer all, wait
45 seconds and the eld will return to its original value.
Warning beeps or vibrations will let you know that this
is happening.
10:10 AM RUNNING

Programming the Pump 14
In a menu, press or 
to highlight the item you
want, then press Select
In screens with multiple elds, you
will press or to change the
item, then press Next to move
to the next item (in this case,
minutes). Press Done to save the
changes and return to the menu
Sample screens
When at the top or bottom
of a menu, only the or 
indicator is shown
If the value you are editing is highlighted,
press or to scroll through the
available values. When the value you
want appears, press Next to move
forward to the next screen, or press Back
to back up one screen. Any changes you
have made will be saved when you press
either Next or Back
Home screen example
Medication remaining in the
cartridge (approximate) Power remaining in the battery
(approximate)
Press the and/or keys to move
through the home screen pages
The home screen
name
{
Current status
of the pump
Press
the right
programming
key to
accomplish
what is
indicated
(in this case,
you will go to
main menu)
Press the left
programming
key to
accomplish
what is
indicated
(in this case,
you go to
Continuous
Rate menu)

<Back Next>
Low Cartridge
Alert
0.2 ml

<Home Select>
Start Delivery
Setup
Delivery Programs
Load
History
Main Menu
1

CR Menu Menu>
Pump Stopped
##
2.988 ml

<Done Next>
Time and Date
Time: 08 : 00 AM
Date: 06 / 28 / 05
CR