Socket DuraScan D730 User manual

Bluetooth Barcode Laser Scanner
Model D730
www.socketmobile.com
DURASCANTM
SERIES 700
socketmobile.com

Package Contents 4
Product Information 5
Scanner Setup 6
Charge the Battery 7
Optional Charging Accessories 8
Powering Scanner On/Off 9
Scanning Barcodes 10
Bluetooth Connection Modes 11
Setup without software application (Basic Mode):
• Android 13
• Apple® 14
• Windows PC® 15
TABLE OF CONTENTS

Setup using software (Application Mode):
• Android 16
• Apple® iOS 18
• Windows PC 20
Unpairing Bluetooth Connection 22
Bluetooth Reconnection of Scanner 23
Scanner Status Indicators 24
Scanner Specifications 28
Helpful Resources 30
Safety, Compliance &Warranty 31-40
Battery Warning 36-37
Advanced Scanner Settings (Command Barcodes) 41
Language Settings (Command Barcodes) 45
TABLE OF CONTENTS

© 2010-2016 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and
SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The
Bluetooth word mark and logo are registered trademarks of the Bluetooth SIG, Inc.
USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and
trade names contained herein may be those of their respective owners.
USB A to USB
Type-C Cable
Lanyard
DuraScan
D730
Thank you for choosing Socket Mobile!
Let’s get started!
PACKAGE CONTENTS

PRODUCT INFORMATION
5
The D730 has a protection rating of IP54 for dust and water resistance. It is also
made with antimicrobial additives to help provide protection against bacteria.
*Also used to display the on-screen keyboard in Basic Mode (iOS only).
Scanner Head
Product Label
Lanyard Eyelet
Scan Indicator Light
(Green/Red)
Trigger Button
Power Button*
Battery Light (Green/Yellow/Red)
Bluetooth Light (Blue)
Charging
Pins
Power Connector Stand Attachment

Attach the Lanyard (optional)
1. Detach the string loop of the tether from the lanyard.
2. Feed the string loop through the eyelet.
3. Pull the tether through the string loop.
4. Pull tight so the string loop is secure.
5. Reattach the string loop’s tether to the lanyard.
SCANNER SETUP
6

The scanner must be fully charged before rst use. Please allow 6 hours
uninterrupted charging for the initial battery charge.
Lift the rubber ap to access the power connector.
• Blinking Yellow Light = Charging
• Solid Green Light = Fully charged
Important: Charging from a computer USB port is not reliable and
not recommended.
CHARGE THE BATTERY
Rubber Flap
To open
Power Adapter
7

Available separately.
OPTIONAL CHARGING ACCESSORIES
8
Charging Cradle Charging Stand AC Power Supply
International Adapters
available
*Recommended power
supply
(1000 mAh - 5.0 volts)
For all optional accessories visit our Socket Store.

Powering On:
Press and hold down the small
power button until the Battery
light turns on and the scanner
beeps twice (low-high).
Powering Off / Disconnecting:
Press and hold down the small
power button until the scanner
beeps twice (high-low) and all
lights turn off.
Scanner will power off
automatically if device is not con-
nected within 5 minutes. Scanner
connected to a device will power
off within 2 hours if idle/inactive.
POWERING ON/OFF
Power button
9

1D Laser Barcode Scanner
Aim the scan beam
across the entire barcode
Scanning Barcodes
1. Hold the scanner a few inches from the barcode.
2. Aim, press and hold the trigger button.
By default, the scanner will beep, vibrate, and the scan indicator will
ash green to conrm a successful scan.
Caution: Do not stare directly into the scanner’s laser beam.
SCANNING BARCODES
Trigger button
10