Socomec Countis e15 User manual

COUNTIS E15/E16

Single-phase active energy meter

80A direct M-BUS

Operating instructions EN

2COUNTIS E15/E16 - Ref.: 542 102 A

Contents

1. DOCUMENTATION ...................................................................3

2. DANGER AND WARNING............................................................3

2.1. RISK OF ELECTROCUTION, BURNS OR EXPLOSION ..................................3

2.2. RISK OF DAMAGING DEVICE ........................................................3

3. PRELIMINARY OPERATIONS........................................................3

4. OVERVIEW ...........................................................................4

4.1. MAIN FUNCTIONS ..................................................................4

4.2. DISPLAY VIEWS ....................................................................4

5. INSTALLATION .......................................................................5

5.1. RECOMMENDATIONS...............................................................5

5.2. DIMENSIONS.......................................................................5

5.3. TERMINALS ........................................................................5

5.4. CONNECTIONS.....................................................................6

5.4.1. 2-WIRE CONNECTION - SINGLE-PHASE LOAD MONITORING ......................6

5.5. SEALABLE COVERS ................................................................6

6. M-BUS COMMUNICATION ..........................................................7

6.1. GENERAL POINTS ..................................................................7

6.2. RECOMMENDATIONS...............................................................7

6.3. COMMUNICATION STRUCTURE .....................................................7

6.4. COMMUNICATION TABLE ...........................................................7

7. PROGRAMMING .....................................................................8

7.1. NAVIGATION PRINCIPLE ............................................................8

7.2. PROGRAMMING MENU OVERVIEW ..................................................8

7.3. DETAILED VIEW OF M-BUS PROGRAMMING MENU ...................................9

8. OPERATION ..........................................................................10

8.1. DETAILED VIEW OF MENUS .........................................................11

9. DIAGNOSTIC MESSAGE.............................................................12

10. ASSISTANCE........................................................................12

11. TECHNICAL/ELECTRICAL CHARACTERISTICS ..................................13

12. MID COMPLIANCE .................................................................14

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

1. Documentation

All the documentation for COUNTIS E15/E16 equipment is available

online at:

www.socomec.com/en/countis-e1x

2. Danger and warning

This equipment must only be installed by professionals.

The manufacturer shall not be held responsible for failure to comply with the instructions in this manual.

2.1. Risk of electrocution, burns or explosion

• Thedevicemustbeinstalledandservicedonlybyqualiedpersonnel.

• Alwaysuseanappropriatevoltagedetectiondevicetoconrmtheabsenceofvoltage.

• Replace all devices, doors, and covers before turning on power to this equipment.

• Always supply the device with the correct rated voltage.

Failure to take these precautions could cause serious injuries.

2.2. Risk of damaging device

Check the following:

• the mains frequency (50 Hz).

• the maximum voltage at the voltage input terminals is 276 VAC phase/neutral.

• a maximum current of 80 A.

3. Preliminary operations

For personnel and product safety, please carefully read the contents of these operating instructions before installation.

Check the following points as soon as you receive package containing the COUNTIS E15/E16:

• the packaging is in good condition,

• the product has not been damaged during transportation,

• the product reference number conforms to your order,

• the packaging contains the product, two sealable covers, two plastic seals and a Quick Start guide.

4COUNTIS E15/E16 - Ref.: 542 102 A

4. Overview

COUNTIS E15 and E16 are active modular electrical energy meters for monitoring kWh. They are designed for single-

phase networks and enable direct connection up to 80A. They are equipped with a M-BUS communication bus.

4.1. Main functions

• Measurement and display:

- active and reactive energy: Ea+/Ea-/Er+/Er-

- of active and reactive power: P1+/P1-/Q1+/Q1-

• Management of two tariffs: T1/T2

• Measurement of electrical parameters accessible via the communication

- Voltage P-N: V1

- Current: I1

- Active power: P1+/P1-

- Reactive power: Q1+/Q1-

- Apparent power: S1

- Power factor: PF1+/PF1-

- Total active energy: Ea+/Ea-

- Total positive reactive energy: Er+

- Positive active energy per tariff: Ea+

- Positive reactive energy per tariff: Er+

• M-BUS communication

• MID version (according to reference)

Description Reference

COUNTIS E15 4850 3033

COUNTIS E16 (MID) 4850 3034

4.2. Display views

COUNTIS E15: ref. 4850 3033 COUNTIS E16 (MID): ref. 4850 3034

8-digit LCD display

Display of kWh/kvarh

Active and reactive energy imported ->/exported <-

Current tariff

Inductive/reactive power display

Capacitive/reactive power display

Current display (80A on start-up)

Consumption bargraph

(% Pmax)

Metrological LED

Selection/settings button

OK button

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

5. Installation

5.1. Recommendations

• avoid proximity to systems which generate electromagnetic interference,

• avoid vibrations with accelerations in excess of 1 G for frequencies below 50 Hz.

5.2. Dimensions (mm)

L1 N

12346

5.3. Terminals

L1 N

12346

0.61 in/15.5 mm

PZ2

exible or rigid

7 to 50 mm2

2 Nm

0.35 in/9 mm

PZ2

exible 1.5 to 2.5

rigid 1 to 4 mm2

0.8 Nm

6COUNTIS E15/E16 - Ref.: 542 102 A

5.4. Connections

5.4.1. 2-wire connection - single-phase load monitoring

L1 L1 N

230 VAC fn = 50 Hz

’

80A

1543

230 VAC

COM M-Bus T1/2

+-+-

M-BUS

1-3: + (terminals connected internally).

2-4: - (terminals connected internally).

Tariff

5-6: Change of tariff:

0VAC -> Tariff 1

230VAC -> Tariff 2.

Mains

L1:Phase input.

L1: Phase output.

N: Neutral connection.

5.5. Sealable covers

COUNTIS E16 MID

Label scaled

between front and

rear faces

Plastic seal

Terminal covers

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

6. M-BUS communication

6.1. General Information

Inastandardconguration,anM-BUSconnectioncanbeusedtolinkupto250*productswithaPCorPLC,over

arangeof1000meters**.

*dependingontheM-BUSmaster

**dependingonthenumberofproductsandthecommunicationspeed

M-BUS

N 1N1

N 2

N 1 N

M-BUS wiring

Wiring with repeater

≈1000mor250products

Repeater Repeater Repeater

6.2. Recommendations

A JYSTY Nx2x0.8 mm (0.5 mm²) unshielded twisted pair must be used.

A repeater should be used to connect additional products if the distance of 1000 m and/or maximum number of 250

products is exceeded.

If there are more than 250 products, only use the secondary address.

6.3. Communication structure

The product communicates via a M-BUS protocol, which involves a dialogue using a master-slave structure.

COUNTIS (slave) units are compatible with both primary and secondary addressing modes. The primary and

secondaryaddressescanbeconguredviatheproductinterface.

6.4. Communication table

The communication tables and associated explanations are

available on the COUNTIS E15/E16 documentation page online at

the following address:

www.socomec.com/en/countis-e1x

8COUNTIS E15/E16 - Ref.: 542 102 A

7. Programming

7.1. Navigation principle

Theprogrammingmodeenablesthecommunicationparameterstobemodied.Theprocesstonavigateinsidethe

programming mode is described in the following steps:

Access to item to set

> 4 sec

Enter programming mode

(press button for 4 seconds)

Value to be modified

> 4 sec Validate the value

7.2. Programming menu overview

By pressing for 4 seconds, the device will enter the programming mode.

The various screens are accessible according to the sequence:

Programming mode

Primary address

Communication speed

Secondary address

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

7.3. Detailed view of M-BUS programming menu

x 10

Primary address

sec

x 1

Communication speed

sec

x 1

Secondary address

sec

x 1

sec

x 1

10 COUNTIS E15/E16 - Ref.: 542 102 A

8. Operation

The total and partial active energy values are accessible via the dedicated buttons. Pressing the appropriate button

several times displays all the available measurements. All the available information and measurements are described

in the following diagram:

Tariff T1

Ea+ (kWh)/P+ (kW)

______________

Tariff T1

Ea- (kWh)/P- (kW)

______________

Tariff T1

Er+ (kvarh)/Q+ (kvar)

______________

Tariff T1

Er- (kvarh)/Q- (kvar)

______________

Tariff T2

Ea+ (kWh)/P+ (kW)

______________

Tariff T2

Ea- (kWh)/P- (kW)

______________

Tariff T2

Er+ (kvarh)/Q+ (kvar)

______________

Tariff T2

Er- (kvarh)/Q- (kvar)

______________

M-BUS primary address

______________

Communication speed

______________

M-BUS secondary address

Note : P (kW) and Q (kvar) power values are only displayed for the current tariff.

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

8.1. Detailed view of menus

Ea+ (kWh)/P (kW) Tariff T1/T2*

Ea- (kWh)/P (kW) Tariff T1/T2*

*Dependingonthecurrenttariffandenergy x 1

Ea+ (kWh) Tariff T1

Ea- (kWh) Tariff T1

Er+ (kVarh) Tariff T1

Er- (kVarh) Tariff T1

Ea+ (kWh) Tariff T2

Ea- (kWh) Tariff T2

Er+ (kVarh) Tariff T2

Er- (kVarh) Tariff T2

P (kW) and Q (kvar) power values are

only displayed for the current tariff

x 7

M-BUS

x 1

12 COUNTIS E15/E16 - Ref.: 542 102 A

9. Diagnostic message

• When these messages are displayed, the meter has malfunctioned and should be replaced.

10. Assistance

Causes Solutions

Error message Check that the meter is working correctly

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

11. Electrical and Technical characteristics

Generalities

Case 3 DIN 43880 modules

Mounting DIN EN 60715 rail

Width 54 mm

Operating specications

Connectivity 230V 2-wire single phase

Storageofenergyvaluesandconguration Yes: EEPROM

Tariffdisplayidentier T1 and T2

Power supply

CertiedvoltageUn 230 VAC

Operating voltage range 110 ... 276 VAC

Frequency range 48 ... 62 Hz

Rated power consumption (max.) Pv ≤8VA(0.6W)

Overload

Direct voltage Un 276 VAC

Instantaneous voltage Un (1 s) 300 VAC

Direct current Imax 80 A

Instantaneous current Imax (10 ms) 2400 A

Display

Screen 8 digits (2 decimal places)

Active energy: 1 x 7-digit screen 0.01 -> 999999.99 kWh

Reactive energy: 1 x 7-digit screen 0.01 -> 999999.99 kvarh

Instantaneous active power: 1 x 3-digit screen 000 ... 999 W, kW/MW

Instantaneous reactive power: 1 x 3-digit screen 000 ... 999 var, kvar/Mvar

Measurement updating period 1 s

Measurement accuracy

Active power and energy (E15) Class 1 IEC 62053-21

Reactive power and energy Class 2 IEC 62053-23

Active power and energy (E16) Class B EN 50470-3

Input measurement

Connection type direct phase/N

Voltage measurement range 110 ... 276 VAC phase/N

Current Iref 5 A

Current Imin 0.25 A

Current measurement range (Ist ... Imax) 0.020 ... 80 A

Certiedfrequency 50 Hz

Start-up current for energy measurement (Ist) 20 mA

Optical interfaces

Pulse value 1 Wh/imp

Safety

Internal meter yes

Degree of pollution 2

Operating voltage 300 VAC

AC voltage test (EN 50470-3, 7.2) 4 kV

Voltage pulse test 6 kV

Protection class (EN 50470) Class II

Casereresistanceclass Class V0

Integrated communication

M-BUS 2-wire up to 9600 bps

Connection terminals

Cross-section of phase connections exibleorrigid:7to50mm2

Cross-section of tariff and communication connections exible1.5to2.5/rigid1to4mm2

Environmental conditions

Mechanical environment M1

Electromagnetic environment E2

Operating temperature -25 ... +55°C

Storage temperature -25 ... +70°C

Relative humidity ≤80%

Amplitude of 50 Hz vibrations ±0.075 mm

IP rating IP51(*)/IP20

(*) For installation in an enclosure with at least IP51 protection.

14 COUNTIS E15/E16 - Ref.: 542 102 A

12. MID compliance

The COUNTIS E16 meter complies with the MID directive for connection of single-phase networks (see "5.4.

Connections", page 6).

Afterconnectingtheproduct,checkthattheterminalcoversarecorrectlyttedandsecuredbythe2plasticseals

supplied with the product (see "5.5. Sealable covers", page 6). If the terminal covers must be removed, ensure

that the same seal part numbers are used (ref. 4850 304U).

The information given via the communication bus is only sent by way of information and has no legal value.

TheassignedoperatingconditionsguaranteeingMIDcomplianceareavailableinthetechnicalspecicationstables.

The MID declaration of conformity for the COUNTIS E16 is available

online at:

www.socomec.com/en/countis-e1x

COUNTIS E15/E16 - Ref.: 542 102 A

COUNTIS E15/E16 M-BUS

Ref. 542 102 B - EN - 03/14

www.socomec.com

HEAD OFFICE

SOCOMEC GROUP

S.A. SOCOMEC capital 10 816 800€

R.C.S. Strasbourg B 548 500 149

B.P. 60010 - 1, rue de Westhouse

F-67235 Benfeld Cedex - FRANCE

Tel. +33 3 88 57 41 41

Fax +33 3 88 74 08 00

socomec COUNTIS E15 User manual

Popular Measuring Instrument manuals by other brands