socomec COUNTIS ATd User manual

Switching and Protection Systems
COUNTIS ATd
Operating instructions
F D I NL
GB E P
SOCOMEC GROUP SWITCHGEAR AND UPS

2SOCOMEC - Réf. : 875 452B

SOCOMEC - Réf. : 875 452B 3
Contents
PRELIMINARY OPERATIONS___________________10
GENERAL INFORMATION______________________10
INSTALLATION ________________________________11
ELECTRICAL CONNECTIONS __________________12
PROGRAMMING ______________________________14
TECHNICAL CHARACTERISTICS _______________15
GB

4SOCOMEC - Réf. : 875 452B
PRELIMINARY OPERATIONS
GENERAL INFORMATION
Check the following points as soon as
you receive the Countis ATd package:
•the packing is in good condition,
•the product has not been damaged
during transit,
Recommendation:
For personnel and product safety
please read the contents of these
operating instructions carefully before
connecting.
•the product reference number con-
forms to your order,
•the package contains the product
fitted with 2 terminal shrouds,
•operating instructions.
The Countis ATd is an active energy
meter with 80A direct input. This pro-
duct enables direct readings of total
or partial consumption via LCD dis-
play, and is thus fully compliant with
standard IEC 61036 Class 1. It is enti-
rely programmable and has a fixed
100Wh pulse output.
The Countis ATd is housed in a
modular case (7 versions).
The display and key-pad make it a
truly user-friendly instrument.
kWh consumption display
Flashing icon indicating incorrect
connection
Total and partial display, or
scrolling in programming mode
3
2
1
Confirm programming
Consumption indicator
(10Wh/pulse)
5
4
126
15
2
34
COUNT 058C
FUNCTIONS
PRESENTATION

SOCOMEC - Réf. : 875 452B 5
ENGLISH
INSTALLATION
The Countis ATd is fitted on a DIN rail,
mounting plate or on the front of a
control panel with a special mounting
kit. (Please contact us for more infor-
mation)
•avoid proximity to systems which ge-
nerate electromagnetic interference
•avoid vibrations with accelerations
in excess of 1 G for frequencies
below 60 Hz.
To guarantee optimal operation, it is
recommended to use this equipment
at -5 up to 45°C with maximum rela-
tive humidity of 85%.
To avoid damage to the device please
ensure the following points are res-
pected before connecting:
•the indications on the case,
•power supply for model 230:
230V AC phase/phase +/-15%, or
power supply for model 400:
400V AC phase/phase +/-20%,
•60 Hz network,
•80 A maximum current,
•minimum cable section.
MECHANICAL ENVIRONMENT
CLIMATIC ENVIRONMENT
SAFETY INSTRUCTIONS

6SOCOMEC - Réf. : 875 452B
Tighten
screws to
pierce
cable insulation
Tighten
terminal
screws to
trap cable
VN POWER V1 V2 V3IN I1 I2 I3
1100 Wh 2
IN I1 I2 I3
100 Wh
NB:
This method offers several connection
possibilities for current and voltage.
Cables can be passed through the
device for the current, whilst other
cables can be used for the voltage
connected to their respective terminals.
Recommendation:
Cables should follow the direction
indicated by the arrows on the enclo-
sure.
The use of 500 mA gG (or BS 88
2A gG) fuses is recommended for
voltage input protection when using
specific cable for voltage.
COUNT 063B GB
The Countis ATd has two connection
modes for current and voltage.
Remove the two covers to access the
terminals.
TERMINAL-FREE CONNECTION
ELECTRICAL CONNECTIONS
•Single-phase (1 BL):
- Current measurement:
Pass cable through I1 and IN.
- Voltage measurement:
Perforate cable insulation for cable
passing through I1 and IN, or
connect V1 and VN.
NB: It is imperative to use cable with
a maximum section of 2.5mm2bet-
ween terminals V2 and VN.
•Two-phase (2BL):
- Current measurement:
Pass cable through I1 and I2.
- Voltage measurement:
Perforate cable insulation for cable
passing through I1 and I2, or
connect V1 and V2.
•Three-phase (balanced) with or
without neutral (3 or 4 BL)
- Current measurement:
Pass cable through I1.
- Voltage measurement:
Connect V1, V2, V3 and VN
(if neutral is distributed).
•Three-phase (unbalanced) with
or without neutral (3 or 4 NBL)
- Current measurement:
Pass cables through I1, I2, I3 and
IN (if neutral is distributed).
- Voltage measurement:
Perforate cable insulation for
cables passing through I1, I2, I3
and IN (if neutral is distributed),
or connect V1, V2, V3 and VN
(if neutral is distributed).

SOCOMEC - Réf. : 875 452B 7
ENGLISH
Remove the two covers to access the
terminals.
Tighten terminal screws
to trap cable
Tighten
terminal screws
to trap cable
VN POWER V1 V2 V3IN I1 I2 I3
1100 Wh 2
IN I1 I2 I3
100 Wh
For optimal operation use cable
connections with the following
sections:
A reed relay (100 V - 0,5 A - 10 VA)
available on the Countis ATd provides
a pulse for active energy, the value
being fixed at 100 Wh. The duration
can be programmed (see §program-
ming).
4mm
2(flexible and rigid) from 0 to 32 A,
10 mm2(flexible and rigid) from 32 to 63 A,
16 mm2(flexible and rigid) from 63 to 80 A.
COUNT 064B GB
SCREW-IN CONNECTION
Recommendation:
Cables should follow the direction
indicated by the arrows on the enclo-
sure.
The use of 500 mA gG (or BS 88 2A gG)
fuses is recommended for voltage
input protection when using specific
cable for voltage.
•Single-phase (1 BL):
- Current measurement:
Connect top and bottom of I1.
- Voltage measurement:
Connect terminals V1 and VN.
NB: It is imperative to use cable with
a maximum section of 2.5mm2bet-
ween terminals V2 and VN.
•Two-phase (2BL):
- Current measurement:
Connect top and bottom of I1
and I2.
- Voltage measurement:
Connect terminals V1 and V2.
•Three-phase (balanced) with or
without neutral (3 or 4 BL):
- Current measurement:
Connect top and bottom of I1.
- Voltage measurement:
Connect V1, V2, V3 and VN
(if neutral is distributed).
•Three-phase (unbalanced) with
or without neutral (3 or 4 NBL):
- Current measurement:
Connect top and bottom of I1, I2,
I3 and IN (if neutral is distributed).
- Voltage measurement:
Connect V1, V2, V3 and VN
(if neutral is distributed).
PULSE OUTPUT
VN POWER V1 V2 V3IN I1 I2 I3
1100 Wh 2
IN I1 I2 I3
100 Wh
COUNT 072A

8SOCOMEC - Réf. : 875 452B
PROGRAMMING
KEYS INSTRUCTIONS
+Press for approx. 3 seconds to access
programming mode password
To enter code 167
To confirm code and access network
type programming
To select 3-4 nbL network type
(unbalanced three-phase), 3-4 bL
(balanced three-phase with 1 CT), 1 bL
(single-phase) and 2 bL (two-phase
with 1 CT)
To confirm network type and proceed
to impulse duration setting (PLS)
To select pulse duration from set list
(60, 100, 200, 300, 400, 500, 600,
700, 800 and 900 ms)
To set duration and proceed to partial
meter reset (rSEt)
To select ‘rSEt nO’(no reset to zero)
and ‘rSEt YES’(reset to zero)
To confirm reset to zero and return to
network type programming
To confirm and quit programming.
+
NB:
Programming quits automatically if no
key is pressed after a 25-second
interval.

SOCOMEC - Réf. : 875 452B 9
ENGLISH
Current and voltage connection (max. 10.5mm):
•via terminal-free cable: 25 mm2max.
•terminals: from 4 m2to 50 mm2
TECHNICAL CHARACTERISTICS
Operating temperature: -5 up to 45°C
Storage temperature: -20 up to 70°C
PULSE OUTPUTS
OPERATING CONDITIONS
Reed relay 100 V DC - 0.5A - 10 VA
Pulse duration: 60 to 900 ms
Maximum number of operations: 5 x 107/ 10 V DC/10 mA
Fixed pulse value: 100 Wh
Relative humidity: 85 %
Voltage and pulse output connection: 1 to 6 mm2(flexible cable)
and 1.5 to 10 mm2(rigid cable)
Weight: 700 gr.
Display: 7-digit green LCD
FRONT FACE
INPUTS
CURRENT
Maximum measured current: 80 A
Minimum measured current: 800 mA
Overload:
•permanent: 80 A
•intermittent: 30 Imax / 10 ms
VOLTAGE
Consumption: ≤2VA
Active energy accuracy: IEC 61036 / Class 1
EC Marking: EN 50081-2
EN 50082-2
IEC 61000-4/2-3-4-5-6-11
STANDARDS
Environment: IEC 60068-2-6
IEC 60669-1 and 60699-2
CASE
NB:
The Countis ATd is self-supplied via
voltage inputs V1 and V2.
IP index: IP40 (front panel) and IP20 (case)
Dimensions: 7 modules (7 x 18 mm)
Consumption:
•screw-in cables: ≤2.5 VA
•terminal-free cables: ≤0.1 VA
Measurement range (Ph/Ph):
•230 V AC ± 15% (230 model)
•400 V AC ± 20% (400 model)
Frequency: 50/60 Hz ± 2Hz

Ref. : 875 452B - 03/04 COUNT 062C
HEAD OFFICE
SOCOMEC GROUP SWITCHGEAR AND UPS
S.A. capital 11 052 200 €- R.C. Strasbourg 548500 149 B
1, rue de Westhouse - B.P. 10 - 67235 Benfeld Cedex
Tél. [phone]
Fax [phone]
SALES MANAGEMENT DIVISION
SOCOMEC
95, rue Pierre Grange
94132 Fontenay-sous-Bois Cedex
Tél. [phone]
Fax [phone]
www.socomec.com
Switching and Protection Systems
Тел./факс: [phone]
ООО "Энергетические и Телекоммуникационные Системы"
http://www.entel.ru, E-Mail: [email protected]