socomec TR-10 User manual

www.socomec.com/en/diris-digiware
INSTALLATION AND OPERATING MANUAL
Multi-circuit Power Metering and Monitoring System
DIRIS Digiware AC
EN

2DIRIS Digiware - 542875G - SOCOMEC
EN
1. DOCUMENTATION ................................................................................... 6
2. HAZARDS AND WARNINGS ........................................................................... 7
2.1. Risk of electrocution, burns or explosion .......................................................... 7
2.2. Risk of damaging the device .................................................................... 7
2.3. Responsibility ................................................................................. 8
3. PRELIMINARY OPERATIONS .......................................................................... 8
4. PREREQUISITES ..................................................................................... 8
5. INTRODUCTION ..................................................................................... 9
5.1. DIRIS Digiware System ......................................................................... 9
5.1.1. Range................................................................................. 10
5.1.2. Principle ............................................................................... 12
5.1.3. Functions .............................................................................. 14
5.1.4. Measured electrical parameters ........................................................... 15
5.1.5. Dimensions ............................................................................ 18
5.2. Presentation of the associated current sensors.................................................... 20
5.2.1. TE solid-core current sensors ............................................................. 21
5.2.2. TR/iTR split-core current sensors .......................................................... 23
5.2.3. TF flexible current sensors................................................................ 24
5.2.4. Adaptor for 5A current transformers ....................................................... 25
6. INSTALLATION ...................................................................................... 26
6.1. Recommendations and safety .................................................................. 26
6.2. DIRIS Digiware mounting ...................................................................... 26
6.2.1. DIRIS Digiware C, U, I-3x, I-6x, IO-x - DIN rail-mounting ...................................... 26
6.2.2. DIRIS Digiware C, U, I-3x, I-6x, IO-x - backplate-mounting .................................... 26
6.2.3. DIRIS Digiware I-4x - DIN rail mounting..................................................... 27
6.2.4. DIRIS Digiware I-4x - back-plate mounting .................................................. 27
6.2.5. DIRIS Digiware S – DIN rail mounting ...................................................... 28
6.2.6. DIRIS Digiware S – Back plate mounting ................................................... 28
6.2.7. DIRIS Digiware S holding................................................................. 28
6.2.8. Accessories overview.................................................................... 29
6.3. Installing TE solid-core sensors ................................................................. 30
6.3.1. Mounting accessories ................................................................... 30
6.3.2. DIN rail mounting ....................................................................... 30
6.3.3. Back-plate mounting .................................................................... 32
6.3.4. Installing on a cable with clamping collar ................................................... 34
6.3.5. Bar mounting........................................................................... 35
6.3.6. Sensors assembly....................................................................... 36
6.3.7. Sealing accessories for sensors ........................................................... 36
6.4. Installing TR/iTR split-core sensors .............................................................. 37
6.4.1. Cable mounting......................................................................... 37
6.5. Installing TF Flexible current sensors............................................................. 38
6.5.1. Bar or cable mounting ................................................................... 38
6.6. Installing the 5A adapter ....................................................................... 39
EN CONTENTS

3
DIRIS Digiware - 542875G - SOCOMEC EN
7. CONNECTION ...................................................................................... 40
7.1. DIRIS Digiware connection ..................................................................... 40
7.2. Connecting the current sensors................................................................. 43
7.2.1. Connection concept..................................................................... 43
7.2.2. Details on the RJ12 connections for each current sensor ..................................... 43
7.3. Connecting to the electrical network and loads.................................................... 44
7.3.1. Configurable loads based on the network type .............................................. 44
7.3.2. Description of the main network and load combinations ...................................... 44
7.3.3. Connection of the functional earth ......................................................... 49
8. DIGIWARE BUS ..................................................................................... 50
8.1. Principle..................................................................................... 50
8.1.1. Digiware Bus connection cables........................................................... 50
8.1.2. Digiware Bus Termination ................................................................ 51
8.2. Sizing of the power supply ..................................................................... 51
8.2.1. Equipment consumption ................................................................. 51
8.2.2. Calculation rules for the max. number of devices on the Digiware BUS .......................... 52
8.2.3. Digiware bus repeater ................................................................... 53
9. STATUS AND LEDS.................................................................................. 54
9.1. DIRIS Digiware U / I / IO / S LEDs............................................................... 54
9.1.1. DIRIS Digiware U / I / IO ................................................................. 54
9.1.2. DIRIS Digiware S........................................................................ 55
10. AUTO-DISCOVERY PROCESS....................................................................... 56
10.1. Auto-discovery from the DIRIS Digiware M gateway............................................... 56
10.2. Auto-discovery from the DIRIS Digiware D display ................................................ 58
11. COMMUNICATION ................................................................................. 59
11.1. General information .......................................................................... 59
11.2. RS485 communication ....................................................................... 59
11.3. Ethernet communication ...................................................................... 60
11.4. Ethernet and RS485 communication ........................................................... 60
11.5. Communication tables ....................................................................... 60
12. CONFIGURATION .................................................................................. 61
12.1. Connection modes .......................................................................... 61
12.2. Configuration via Easy Config System .......................................................... 62
12.3. Configuration from the DIRIS Digiware D remote display ........................................... 62
12.3.1. Connection mode...................................................................... 62
13. ALARMS .......................................................................................... 63
13.1. System alarms .............................................................................. 63
13.2. Measurement alarms......................................................................... 64
13.3. Protection alarms............................................................................ 64
13.4. Protection counter alarms..................................................................... 65
13.5. Logical alarms .............................................................................. 65
13.6. Combination alarms.......................................................................... 66
13.7. EN50160 alarms ............................................................................ 66
13.8. Overcurrent alarm ........................................................................... 66

4DIRIS Digiware - 542875G - SOCOMEC
EN
14. VIRTUALMONITOR TECHNOLOGY: MONITORING OF PROTECTIVE DEVICES ............................ 67
15. AUTOCORRECT TECHNOLOGY: AUTOMATIC DETECTION OF WIRING ERRORS ANDSOFTWARE CORRECTION .. 70
15.1. Identifying the wiring error from the DIRIS Digiware D-50/D-70 display ............................... 70
15.2. Identifying the wiring error from the Easy Config System software ................................... 73
16. TECHNICAL CHARACTERISTICS .................................................................... 76
16.1. DIRIS Digiware C, U, I, S and IO technical characteristics.......................................... 76
16.1.1. Mechanical characteristics .............................................................. 76
16.1.2. Electrical characteristics ................................................................ 76
16.1.3. Measuring characteristics ............................................................... 76
16.1.4. Communication characteristics........................................................... 78
16.1.5. Environmental characteristics ............................................................ 79
16.1.6. Electromagnetic characteristics .......................................................... 79
16.1.7. Standards and safety................................................................... 79
16.1.8. Service life ............................................................................ 79
16.2. TE, TR/iTR and TF sensor technical characteristics ............................................... 80
16.2.1. General characteristics ................................................................. 80
16.2.2. Electromagnetic compatibility and insulation levels .......................................... 82
16.3. DIRIS D-30 - technical characteristics .......................................................... 82
16.3.1. Mechanical characteristics .............................................................. 82
16.3.2. DIRIS D-30 communication characteristics................................................. 82
16.4. DIRIS Digiware D-50/D-70 & M-50/M-70 characteristics........................................... 83
16.4.1. Mechanical characteristics .............................................................. 83
16.4.2. Electrical characteristics ................................................................ 83
16.4.3. Communication characteristics........................................................... 83
16.4.4. Environmental characteristics ............................................................ 83
17. PERFORMANCE CLASSES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
17.1. DIRIS Digiware I ............................................................................. 84
17.2. DIRIS Digiware S ........................................................................... 85
EN CONTENTS

5
DIRIS Digiware - 542875G - SOCOMEC EN

6DIRIS Digiware - 542875G - SOCOMEC
EN
1. DOCUMENTATION
All documentation relating to DIRISDigiware and its associated sensors is
available on the SOCOMEC website at the following address:
www.socomec.com/en/diris-digiware
Related instruction manuals
Additional instruction manuals linked to the DIRIS Digiware system can be found on the Socomec website:
Instruction manual Reference
Easy Config System - Configuration Software 551765
Product Upgrade Tool - Software for firmware upgrade 545534
WEBVIEW-M - Energy Server embedded DIRIS Digiware M & D 551295

7
DIRIS Digiware - 542875G - SOCOMEC EN
2. HAZARDS AND WARNINGS
The term "device" used in the following paragraphs encompasses DIRISDigiware and its associated current sensors
(TE, TR/iTR or TF).
The assembly, use, servicing and maintenance of this equipment must only be carried out by trained, qualied professionals.
SOCOMEC shall not be held responsible for failure to comply with the instructions in this manual.
2.1. Risk of electrocution, burns or explosion
Caution: risk of electric shock Ref. ISO 7000-0434B (2004-01)
Caution: refer to the accompanying documentation each time this
symbol is shown Ref. ISO 7000-0434B (2004-01)
• Only duly authorised and qualied personnel may work or install/uninstall the device.
• The instructions are valid together with the specic instructions for the device.
• The device is designed only for its intended purpose as set out in the instructions.
• Only accessories authorised or recommended by SOCOMEC may be used in association with the device.
• Before proceeding with installation, maintenance, cleaning, disassembly, connection, or maintenance work, the device
and system must be cut off from the mains to avoid electrocution and damaging the system and device.
• This device is not designed to be repaired by the user.
• For any questions related to the disposal of the device, please contact SOCOMEC.
Do NOT clamp or pull out NON-INSULATED conductors carrying DANGEROUS VOLTAGE which
could cause an electric shock, burn or arc ash.
Ref. IEC 61010-2-032
Failure to comply with the instructions of the device and this safety information can cause bodily injury, electric
shock, burns, death or damage to property.
2.2. Risk of damaging the device
Caution: risk of electric shock Ref. ISO 7000-0434B (2004-01)
Caution: refer to the accompanying documentation each time this
symbol is shown Ref. ISO 7000-0434B (2004-01)
To ensure that the device operates correctly, make sure that:
• The device is correctly installed.
• The auxiliary power supply voltage indicated on the device is observed: 24VDC ±10%.
• The use of a SOCOMEC 230 VAC / 24 VDC power unit or a 24 VDC max 20 W class 2 power unit / SELV according to
UL1310. The device must be protected with a 1A 24 VDC fuse.
• The network frequency indicated on the device is observed: 50 or 60 Hz.
• A maximum voltage at the voltage input terminals of 520 VAC phase/phase or 300 VAC phase/neutral is observed.
• Always connect the TE, TR/iTR or TF current sensors using the recommended connection cables and observing the
maximum prescribed currents.
• Only use RJ45 SOCOMEC cables to interconnect the modules via the Digiware bus.
Failure to respect these precautions could cause damage to the device.

8DIRIS Digiware - 542875G - SOCOMEC
EN
2.3. Responsibility
• Assembly, connection and use must be carried out in accordance with the installation standards currently in force.
• The device must be installed in accordance with the rules given in this manual.
• Failure to observe the rules for installing this unit may compromise the device's intrinsic protection.
• The device must be placed in a system which itself complies with the applicable standards and safety regulations of
the country of installation.
• Any cable which needs to be replaced may only be replaced with a cable having the correct rating.
• Despite constantly striving for quality in preparing this manual, errors or omissions are always a possibility and are not
the responsibility of SOCOMEC.
3. PRELIMINARY OPERATIONS
To ensure the safety of personnel and the device, please carefully read the contents of these instructions before
installation.
Check the following points as soon as you receive the package containing the device, one or several sensors:
• The packaging is in good condition
• The device has not been damaged during transit
• The device part number match your order
• The packaging includes the device tted with removable terminal blocks and a Quick Start Guide.
4. PREREQUISITES
Before commissioning your DIRIS Digiware system, make sure all equipment operate under the latest rmware versions.
The latest rmware versions are available on the Socomec website.
The rmware upgrade is done using the Product Upgrade Tool software, by connecting a laptop to the Micro USB port of
your DIRIS Digiware equipment.
For DIRIS Digiware M-50/M-70 and D-50/D-70, rmware upgrade can also be done remotely directly from their
embedded webserver.

9
DIRIS Digiware - 542875G - SOCOMEC EN
5. INTRODUCTION
5.1. DIRIS Digiware System
DIRIS Digiware is a measurement system (PMD*) with modular format. It always comprises a voltage measurement
module (U-xx) and one or several current measurement modules.
The current measurement modules can be of two types:
• DIRIS Digiware S with 3 integrated current sensors to measure circuits up to 63A
• DIRIS Digiware I (with 3, 4 or 6 current inputs) associated with TE, TR /iTR and TF sensors for the measurement from
5A up to 6000A
DIRIS Digiware is an innovative concept based on centralising the voltage measurement by a dedicated DIRIS Digiware
U module and the current by dedicated DIRIS Digiware I or S modules. The voltage and current measurements are
interconnected by the Digiware bus. Several modules may be connected to the Digiware bus. This approach offers the
possibility of characterising a high number of loads from a single voltage tap.
Cabling is made simple by a single voltage measurement connection. The connection mode for the current sensors also
contributes to quick, easy installation and the automatic identication of the sensor (type and rating) signicantly reduces
the risk of installation errors. In addition, combining the current sensor with DIRISDigiware means the overall accuracy of
DIRISDigiware + Current sensor measurement chain can be guaranteed for all values measured.
DIRIS Digiware is congured from its remote display or via the Easy Cong System software. The measurements can be
viewed on WEBVIEW-M, a web-based visualisation and analysis software embedded in the DIRIS Digiware M-70/D-70.
Thanks to its architecture, DIRIS Digiware can be easily integrated into an energy management system which requires a
large number of loads to be monitored.
* PMD: Power Metering and Monitoring Device in accordance with IEC 61557-12.

10 DIRIS Digiware - 542875G - SOCOMEC
EN
5.1.1. Range
Communication and power supply interface
DIRIS Digiware C
System interface*
DIRIS Digiware C-31
Ref. 4829 0101
*if there is no multipoint display
DIRIS Digiware C-32
Ref. 4829 0103
DIRIS Digiware M
Communication gateway
DIRIS Digiware M-50
Ref. 4829 0219 (without Bluetooth)
Ref. 4829 0221 (with Bluetooth)
DIRIS Digiware M-70
Ref. 4829 0220 (without Bluetooth)
Ref. 4829 0222 (with Bluetooth)
DIRIS Digiware D
Multi-point display
DIRIS Digiware D-50
Ref. 4829 0204
DIRIS Digiware D-70
Ref. 4829 0203
Voltage measurement
module Current measurement module
DIRIS Digiware U-x
Voltage measurement
DIRISDigiware U-10
Ref. 48290105
DIRISDigiware U-20
Ref. 48290106
DIRISDigiware U-30
Ref. 48290102
DIRIS Digiware I-3x
3 current measurement
inputs
DIRISDigiware I-30
Ref. 48290110
DIRISDigiware I-31
Ref. 48290111
DIRISDigiware I-33
Ref. 48290128
DIRISDigiware I-35
Ref. 48290130
DIRIS Digiware I-4x
4 current measurement
inputs
DIRISDigiware I-43
Ref. 4829 0129
DIRISDigiware I-45
Ref. 4829 0131
DIRIS Digiware I-6x
6 current measurement
inputs
DIRISDigiware I-60
Ref. 48290112
DIRISDigiware I-61
Ref. 48290113

11
DIRIS Digiware - 542875G - SOCOMEC EN
Current measurement and sensing
module
DIRIS Digiware S
3 current measurement inputs
DIRIS Digiware S-130
Ref. 4829 0160
DIRIS Digiware S-135
Ref. 4829 0161
DIRIS Digiware S-Datacenter
Ref. 4829 0162
IO input/output modules
DIRIS Digiware IO-10
Digital inputs/outputs
DIRISDigiware IO-10
Ref. 48290140
DIRIS Digiware IO-20
Analogue inputs
DIRISDigiware IO-20
Ref. 48290145

12 DIRIS Digiware - 542875G - SOCOMEC
EN
5.1.2. Principle
DIRIS
Digiware U
Voltage
measurement
(U)
D
i
g
i
w
a
r
e
B
u
s
L1
L2
L3
N
Multipoint display
DIRIS Digiware D
or
Communication gateway
DIRIS Digiware M
DIRIS
DigiwareI
Current
inputs (3I)

13
DIRIS Digiware - 542875G - SOCOMEC EN
DIRIS
DigiwareIO
Inputs/
outputs
DIRIS
Digiware I
DIRIS
Digiware S
DIRIS
DigiwareI
Current
inputs (4I)
Current
inputs (6I)
Current sensors
TE, TR/iTR or TF

14 DIRIS Digiware - 542875G - SOCOMEC
EN
5.1.3. Functions
DIRIS Digiware offers numerous functions, including:
• General measurements
- Voltage measurement
- Multi-load current measurement
- Power, power factor, phi, cos phi and tan phi
- Operation across 4 quadrants
- Predictive power
- Accuracy of the active energy class 0.5 according to the IEC 61557-12 standard
• Power quality
- THD and harmonics up to 63rd for voltage and current
- K-factor
- Crest Factor for voltage and current
- Current and voltage unbalance
- Direct, inverse and zero-sequence voltages and currents
- EN50160 events (Uswl, Udip, Uint) and overcurrents
• Data logging
- Recording of average electrical values
- Recording and timestamping of min/max electrical values
• Metering
- Total and partial active, reactive and apparant energies (+/- kWh, +/- kVarh, kVAh)
- Load curves / demand proles
• Alarm
- Timestamped alarms with boolean combination
• Current inputs
- Measurement of 3, 4 or 6 currents per current measurement module
- Current inputs with quick connection and automatic recognition of the current sensors
- Simultaneous management of several single-phase, two-phase and three-phase loads
- Connection of solid-core, split-core and exible sensors
- Checking the connection, detecting the CT and auto-conguring the networks
- Accuracy of the global measurement chain (DIRIS Digiware + sensors) = Class 0.5 performance according
to IEC 61557-12
• Inputs/outputs
- Analogue and digital inputs/outputs
• Communication
- RS485 or Ethernet communication ports
- Multiple communication protocols (Modbus RTU, Modbus TCP, BACnet IP, SNMP V1, V2, V3 & Traps)
- Measurements available in the web server (WEBVIEW-M) embedded in the DIRIS Digiware M-70 gateway and
DIRIS Digiware D-70 display
- Time synchronisation done by the DIRIS Digiware M-50/M-70 gateway and DIRIS Digiware D-50/D-70 display
- Auto-Discovery of slave modules from the DIRIS Digiware M gateway and DIRIS Digiware D display

15
DIRIS Digiware - 542875G - SOCOMEC EN
5.1.4. Measured electrical parameters
DIRIS Digiware
C-31 M-50 M-70 D-50 D-70
Function
Basic system interface •
Multi-point display • •
Multifunction gateway ••••
Power supply
24 VDC •••••
Communication
Master RS485 ••••
Slave RS485 •••••
Digiware bus •••••
Ethernet Modbus TCP ••••
BACnet IP ••••
SNMP v1, v2, v3 & Traps ••••
WEBVIEW-M webserver • •
WEB-CONFIG webserver ••••
Format
Mounting DIN rail DIN rail DIN rail Panel mounted Panel mounted
Dimensions 1 module 9 modules 9 modules 96 mm x 96 mm 96 mm x 96 mm
Reference 48290101 48290219
48290221 (BLE)
48290220
48290222 (BLE) 48290204 48290203
DIRIS Digiware U
U-10 U-20 U-30
Multi-measurement
U12, U23, U31, V1, V2, V3, Vn, F •••
U system, V system •
Ph/N unbalance (Vnb, Vnba, Vdir, Vinv, Vhom) •
Ph/Ph unbalance (Unb, Unba, Udir, Uinv) •
Power quality
THDv1, THDv2, THDv3, THDu12, THDu23, THDu31, THD Vsys, THD Usys • •
Individual harmonics U & V (up to 63rd) •
Crest Factor •
Voltage dips, swells and interruptions according to EN50160 •
Alarms
Thresholds •
Data logging
Trends of average values •
Format
Width/Number of modules 18mm / 1 18mm / 1 18mm / 1
Part number 4829 0105 4829 0106 4829 0102

16 DIRIS Digiware - 542875G - SOCOMEC
EN
DIRIS Digiware I
I-30 I-31 I-33 I-35 I-43 I-45 I-60 I-61
Application Metering Monitoring Analysis Monitoring Analysis Metering
Number of current inputs 33334466
Metering
± kWh, ± kvarh, kVAh ••••••••
Multi-tariff (max. 8) ••••
Load curves ••••
Multi-measurement
I1, I2, I3, In, SP, SQ, SS, SPF ••••••••
P, Q, S, PF per phase ••••
Predictive power • •
Current unbalance
(Inba, Idir, Iinv, Ihom, Iunb) • •
Phi, cos Phi, tan Phi • •
Quality
THDi1, THDi2, THDi3,
THDin, THD Isys ••••
Individual harmonics I
(up to 63rd) • •
Crest Factor • •
Overcurrents • •
Alarms
Thresholds • •
Inputs/outputs
Number 2/2 2/2
Data logging
Trends of average values • •
Format
Width 18 mm 18 mm 18 mm 18 mm 27 mm 27 mm 36 mm 36 mm
Number of modules 11111.5 1.5 2 2
Part number 4829 0110 4829 0111 4829 0128 4829 0130 4829 0129 4829 0131 4829 0112 4829 0113
DIRIS Digiware S
S-130 S-135 S-Datacenter
Application Metering Analysis Monitoring
Number of current inputs 3 3 3
Basic current Ib / Maximum current Imax 10A / 63A 10A / 63A 10A / 63A
Load type accepted
1P+N
2P
2P+N
3P
3P+N
1P+N
2P
2P+N
3P
3P+N
1P+N
Metering
± kWh, ± kvarh, kVAh • • •
Multi-tariff (max 8) •
Load curves / demand profiles • •

17
DIRIS Digiware - 542875G - SOCOMEC EN
DIRIS Digiware S
S-130 S-135 S-Datacenter
Application Metering Analysis Monitoring
Number of current inputs 3 3 3
Basic current Ib / Maximum current Imax 10A / 63A 10A / 63A 10A / 63A
Load type accepted
1P+N
2P
2P+N
3P
3P+N
1P+N
2P
2P+N
3P
3P+N
1P+N
Multi-measurement
I1, I2, I3, In, ∑P, ∑Q, ∑S, ∑PF • • •
P, Q, S, PF per phase • •
Predictive power • •
Current unbalance (Inba, Idir, Iinv, Ihom, Inb) •
Phi, cos Phi, tan Phi • •
Power Quality
THDi1, THDi2, THDi3, THDin, THD Isys • •
Individual harmonics I (up to rank 63) •
Crest Factor I1, I2, I3 •
Inrush •
Alarms
Thresholds • •
Load levels •
System alarms • •
Protection alarms • •
Protection counters • •
Boolean combination of alarms • •
Data logging
Trends of average values • •
Advanced features
Voltage detection • • •
VirtualMonitor technology • • •
AutoCorrect technology • • •
Format
Width 54 mm 54 mm 54 mm
Part number 4829 0160 4829 0161 4829 0162
DIRIS Digiware IO
IO-10 IO-20
Application Metering / Monitoring / Analysis
Number of digital inputs/outputs 4/2 -
Number of analogue inputs - 2
Format
Width 18 mm 18 mm
Number of modules 1 1
Part number 4829 0140 4829 0145

18 DIRIS Digiware - 542875G - SOCOMEC
EN
5.1.5. Dimensions
5.1.5.1. M-50 & M-70 gateways
1.77
45
1.97
50
2.56
65
3.5
89
3.52 89.5
Ø 0.24
Ø 6
4.49
114
0.24
6
Dimensions in/mm
5.1.5.2. D-50 & D-70 displays
3.62
92
3.62
92
0.63
16
1.22
31
Dimensions in/mm
5.1.5.3. DIRISDigiware C, U & I-3x, I-6x, IO-x
1.73
44
0.59
15
2.56
65
1.77
45
0.70
18
0.19
5
1.42
36
3.54
90
3.94
100
Dimensions in/mm
C-3x
U-xx
I-3x
IO-x
I-6x

19
DIRIS Digiware - 542875G - SOCOMEC EN
5.1.5.4. DIRIS Digiware S-xx
2.13
54
0.31
8
1.10
28
0.51
13
1.67 42,5
0.45
11,5
0.61
15.5
0.61
15.5
Dimensions in/mm
5.1.5.5. DIRISDigiware I-4x
2.83
72
1.06
27 1.76
45
0.83
21
1
25.5
5.90
150
2.28
58
1.77
45
Dimensions in/mm

20 DIRIS Digiware - 542875G - SOCOMEC
EN
5.2. Presentation of the associated current sensors
Various types of current sensors are connected to DIRIS Digiware I modules: solid-core (TE), split-core (TR/iTR) or exible
(TF). The variety of these sensors make them suitable with any type of new, existing or high-current existing installation.
They all use a specic link with the DIRIS DigiwareI current measurement module. This link ensures rapid connection
without any wiring error. DIRIS Digiware automatically recognises the type of current sensor that is connected and its
rating.. In addition, combining them means the overall accuracy of DIRISDigiware + Current sensor measurement chain
can be guaranteed over a large measurement range.
DIRIS Digiware
I-30 / I-31 / I-35
DIRIS Digiware
I-4x
DIRIS Digiware
I-60 / I-61
3 Current sensors
TE / TR/iTR / TF
4 Current sensors
TE / TR/iTR / TF
6 Current sensors
TE / TR/iTR / TF
For connecting the current sensors, use SOCOMEC cables or RJ12 straight cables, twisted pair, unshielded,
600V -10°C / +70°C. It is recommended that all the current sensors be installed in the same direction.
Connection cables for current sensors:
RJ12
connection
cables
Cable length (m)
0.1 0.2 0.3 0.5 123510
50m reel
+ 100
connectors*
Number of
cables Ref. Ref. Ref. Ref. Ref. Ref. Ref. Ref. Ref. Ref.
1 ------4829 0606 4829 0602 4829 0603 4829 0601
34829 0580 4829 0581 4829 0582 4829 0595 4829 0583 4829 0584 - - - -
44829 0596 4829 0588 4829 0589 - - - -
64829 0590 4829 0591 4829 0592 4829 0597 4829 0593 4829 0594 - - - -
* When producing cables, do not exceed a maximum length of 10 metres.