socomec COUNTIS ATv2 User manual

Industrial Switching & Protection Systems
COUNTIS ATv2/ATiv2
Operating instructions
GB

2SOCOMEC - Ref. : 875 645 D

SOCOMEC - Ref. : 875 645 D 3
ENGLISH
GB
Contents
PRELIMINARY OPERATIONS ___________________ 4
GENERAL INFORMATION ______________________ 4
PRESENTATION _______________________________ 4
INSTALLATION ________________________________ 5
CONFIGURATION ______________________________ 7
TECHNICAL CHARACTERISTICS _______________ 8

4SOCOMEC - Ref. : 875 645 D
• the product has not been damaged
during transit,
• the product reference number con-
forms to your order,
• the package contains the product as
well as the operating instructions.
For personnel and product safety
please read the contents of these
operating instructions carefully.
Check the following points as soon as
you receive the package:
• the packing is in good condition,
PRELIMINARY OPERATIONS
GENERAL INFORMATIONS
PRESENTATION
The COUNTIS System comprises
energy metering products for balanced
or non-balanced 3- or 4-wire network.
This system comprises two products:
• ATv2: a non-insulated three-phase
active energy-meter, which does not
allow earthing CT of secondary.
• ATiv2: a three-phase insulated single
or double rate active energy meter
allowing the CT secondary to be
earthed.
These products are completely confi-
gurable (CT radio, network type and
pulse output value) and have a 7-digit
display which allows direct display of
consumption in kWh. They are equip-
ped with a pulse output as standard.
1
2
4
3
COUNT 105 A
akWh display
bTotal and partial meter display, or scrolling parameter settings
cFlashing LED consumption indicator (10 Wh/pulse)
dValidation/scrolling of parameter settings
COUNTIS ATv2 / ATiv2 SINGLE RATE

SOCOMEC - Ref. : 875 645 D 5
ENGLISH
CLIMATIC ENVIRONMENT
To guarantee optimum operation, it is
recommended that this device is used
between - 5 to + 45 °C with a relative
humidity of between 20 and 85%.
Note:
The COUNTIS can be installed on a
DIN EN 50022 rail (DIN 43880).
CONNECTION
The Countis ATv2 and ATiv2 consist of
connection terminals of 1 to 6 mm2for
currents and voltages.
Recommendation:
• Avoid close proximity with systems
generating electromagnetic distur-
bances
• Avoid vibrations including accelera-
tions of more than 1 G for frequen-
cies lower than 60 Hz.
SAFETY INSTRUCTIONS (U,I, F)
To avoid damaging the device, take
care to observe the following before
connecting the device:
• indications on the casing,
• network frequency: 50 or 60 Hz,
• maximum permanent voltage at
voltage input terminals of 400 V AC
±20%phase/phase,
• maximum permanent current of 7 A
(connection from current transfor-
mer(s)).
Note:
The minimum torque for the fixed
terminal is 0.8 Nm.
Recommendation:
We recommend that the auxiliary
voltage and the voltage inputs should
be protected with 0.5 A fuses or
BS 88 2A gG.
INSTALLATION
PRESENTATION (continued)
1
2
5
4
3
COUNT 119 B
akWh display
bTotal and partial meter display, or scrolling parameter settings
cDisplays t1 and t2 rate meters
dFlashing LED consumption indicator (10 Wh/pulse)
eValidation/scrolling of parameter settings
COUNTIS ATiv2 DOUBLE RATE

6SOCOMEC - Ref. : 875 645 D
NETWORK
CT earthing, for the ATiv2 only
Note:
If the current is badly connected or
there is poor current/voltage corres-
pondence (negative energy) the coun-
ter will be stopped and the arrows t
flash.
3 WIRE WITH 1 CT (3 BL) 4 WIRE WITH 1 CT (4 BL)
3 WIRE WITH 2 CT (3 NBL) 3 WIRE WITH 2 CT (3 NBL)
3 WIRE WITH 3 CT (3 NBL) 4 WIRE WITH 3 CT (4 NBL)
TWO-PHASE (2 BL) SINGLE-PHASE (1 BL)
Key to diagrams:
1 Fuses 0.5 gG or BS 88 2A gG
L1
L2
L3P1
S1
P1
S1
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
L1
L2
L3
P1
S1
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
L1
L2
L3
P1
S1
ATiv2
2
4
6
8
1
1
3
5
7
9
11
L1
L2
L3P1
S1
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
L1
L2
L3
N
P1
S1
P1
S1
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
L1
L2
L3
N
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
COUNT 106 C COUNT 107 C
COUNT 108 C
COUNT 109 C
COUNT 110 C
L1
L2
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
COUNT 112 C
L1
N
P1
S1
2
4
6
8
1
3
5
7
9
11
ATiv2
1
COUNT 118 C COUNT 111 C
INSTALLATION (continued)
COUNT 35B GB COUNT 147A
CONNECTING PULSE OUTPUT
External counter 1
3
5
7
9
11
External power supply
4
6
2
8
10
12
14
RATE INPUT (t1 / t2)
t1 = 0 VAC
4
6
2
8
10
1
3
5
7
9
11
t2 = 230 VAC
The neutral has to be
connected for the dual
tarif ATiv2.

SOCOMEC - Ref. : 875 645 D 7
ENGLISH
CONFIGURATION
KEY INSTRUCTION
For 3 seconds to access
access-code entry (CdE).
Note:
The device will automatically leave
the configuration menu if no buttons
are pressed for a period of 25
seconds.
Note:
Press the t button for a prolonged
period to scroll rapidly through the
configuration screens. Press for a
short period to scroll through each
screen one-by-one.
Note:
A long press on the button tcauses
rapid scrolling and a single short
press causes scrolling in steps of 5.
Note:
The values available depend on the
Ct ratio.
To enter code 21.
To validate the code and access to
the network programming (nET).
To select the network type, 1bL
(single phase), 2bL (two-phase),
3-4 nbL (unbalanced three-phase)
and 3-4 bL (balanced three-phase).
To validate the network programming
and go on to the current transformer
(CT) primary value.
To programme the primary value up
to 6000 A.
To validate the unit programming and
go on to the pulse output (PuLSES).
To go on to the weight of this output
(VAL).
To select the weight “0.1” for
0.1 kWh, “1” for 1 kWh, “10” for
10 kWh, “100” for 100 kWh.
To validate the programming of this
weight and go on to the pulse
duration (dur).
To select the duration from 60 to
900 ms.
To accept value and pass to partial
meter zero reset (rSET).
To select ‘rSEt nO’ (no reset to zero)
and ‘rSEt YES’ (reset to zero).
To confirm reset to zero and return to
network type programming.
+
To confirm and quit programming.
+

8SOCOMEC - Ref. : 875 645 D
TECHNICAL CHARACTERISTICS
ENCLOSURE
Connection via 1 to 6 mm2terminal shrouds
Weight 300 g
Size modular: 4 modules of 17.5 mm
Protection class (front) IP40
FRONT PANEL
Green LCD/7 digits
Digit height 8 x 4 mm
INPUTS
CURRENT
Via transformer with
• configurable primary 5 to 6000 A
• secondary 5 A
Input consumption 10 mA to 7 A (secondary)
Consumption ≤1 VA
TENSION
Measurement range (Line/Line) 230 V AC - 15% to 400 V AC + 20%
Consumption ≤0,5 VA
AUXILIARY POWER SUPPLY
Type auto-powered
Consumption ≤1 VA
ACCURACY
Accuracy index IEC 61036 class 1
PULSE OUTPUT
Reed relay (100 V DC - 0.5 A - 12 VA)
Pulse duration 60 to 900 ms
Maximum tripping number 5 x 107at 10 V DC/10 mA
OPERATING CONDITIONS
Operating temperature - 5 °C up to 45 °C
Storage temperature - 20 °C up to 70 °C
Relative humidity 85%
STANDARDS
CE marking IEC 61000-4/2-3-4-5-6-8-11
EN 50081-1
EN 50082-2
Operating conditions IEC 60068-2-6
IEC 60068-2-11
IEC 60068-2-30
Note:
The current inputs are insulated on
the ATiv2.
Note:
The Countis ATv2 and ATiv2 are auto-
powered from the V1 et V2 voltage
inputs.

SOCOMEC - Ref. : 875 645 D 9
ENGLISH

SOCOMEC - Ref.: 875 645 D - 10/03
COUNT 113 C
HEAD OFFICE
SOCOMEC GROUP
Switchgear and UPS
S.A. capital de 11 052 200 €
R.C. Strasbourg 5484500 149 B
SOCOMEC
1, rue de Westhouse - B.P. 10
F-67235 Benfeld Cedex -FRANCE
Tel. [phone] - Fax [phone]
SOCOMEC
95, rue Pierre Grange
F-94132 Fontenay-sous-Bois Cedex-FRANCE
Tel. [phone] - Fax [phone]
[email protected]
SALES MANAGEMENT DIVISION
Industrial Switching & Protection Systems
This document is not contractual. SOCOMEC reserves the right to
modify features without prior notice in view of continued improvements.
www.socomec.com