solarwatt VISION 36M GLASS User manual
| |EN
SOLARWATT
INSTALLATION INSTRUCTIONS
Actions on structures
Fire behavior of building materials and buil
ding component
systems
Lightning protection
Operation of electrical systems
EXCLUSION OF LIABILITY
The warranty terms available at
www.solarwatt.com apply.
You can check the current status of the instal
lation instructions at www.solarwatt.com.
www.solarwatt.com.
The following directives and standards must be complied with when planning, setting up, and
VISION 36M GLASS
Congratulations on the purchase of your SOLARWATT Solar Module
These instructions describe the assembly,
connection, maintenance, and disposal of solar
modules. Please read them carefully and com
ply with them accordingly.
The installation and electrical connection of
photovoltaic systems may only be carried out
by specialist personnel, who are familiar with
tions. For the operation, installation, use and
maintenance of the other components, comply
with the relevant installation instructions from
the manufacturer.
Incorrect installation can cause damage to pro
perty, which could consequently pose a risk to
people. SOLARWATT accepts no responsibility
or liability for losses, damage, or costs resulting
from incorrect installation, operation, use, or
maintenance or losses, damage, or costs which
are connected to any of the above in any way.
The SOLARWATT installation instructions should
be made available to the operator as part of the
solar power system documentation and stored
by the operator.
Failure to comply with the installation instructions results in the warranty and guaran
tee becoming null and void.
WARNING
tions valid in the relevant country when plan
ted PV systems. For information on additional
requirements, please contact the responsible
local authorities and the network operator.
cells, and are therefore extremely reliable. The
quality of the solar modules made exclusively
in Germany is ensured by multiple tests carried
out on the products throughout the entire
production process. SOLARWATT solar modules
own research and development department,
tests are carried out using measuring, testing,
and environmental simulation equipment
which go above and beyond the current
valid standards and enable us to optimize
our products continually. If treated correctly,
several decades of service.
SOLARWATT recommends insuring the PV sys
tem against reduced yields or damage with
rity. Further information is available from your
SOLARWATT partner or online at www.solarwatt.
com.
Information on the solar module
the relevant data sheet. The key technical data
plate of the solar module.
Transport and Storage
SOLARWATT solar modules are made from
should nevertheless be left in the packaging
until installation to help prevent any damage.
The modules should be stored in a dry place
and protected from weather conditions. The
ponsible local waste disposal company.
You are responsible for checking the goods and
packaging for transport damage immediately
on receipt. If any damage is discovered, note it
on the shipping papers describing each pallet
in detail, and take photographs as documentary
pallet are damaged, refuse to accept the pallet.
turn it to SOLARWATT.
Installation
locally valid construction regulations, accident
prevention regulations, the relevant, generally
accepted rules of technology and safety regula
tions for working on roofs and buildings, as well
as electrical installations. The modules may be
level.
suitable substructures, which are designed for
the relevant mechanical wind and snow loads,
as well as the weight of the solar modules. The
instructions from the installation system manu
facturer must also be complied with. No mecha
for the installation of a solar power system che
cked by a specialist.
solar modules.
NOTE
module, such as the conversion to the use of
the heat generated in the form of a thermal so
lar collector. If there is no approval in the form
approval, the solar modules may not be instal
led in locations where there are aggressive am
bient conditions. Furthermore, the use of the
products on mobile units such as vehicles or
ships is not permitted.
Make sure that there are no components such
as cable ties, fasteners or similar materials bet
ween the mounting rails and the backside of
the module. When the modules are installed
must be positioned with the junction box to
wards the ridge.
des with the module clips or installati
on system to improve the energy yield.
between the solar modules to allow the materi
al to expand without tension.
For system documentation, note the positions
system is recommended.
the solar module. Never hold or transport the solar module by the junction box or con
nection cables. For installation SOLARWATT strongly recommends the usage of clean,
fat and silicone oil free gloves!
WARNING
trating solar irradiation through lenses or mirrors is therefore not permitted and can
damage the solar modules.
WARNING
making them ideal for use in areas with large
amounts of snow. The local regulations or the
used for the calculation of the snow loads on
the module. It is important to note that these
standards are designed for impact on structures
and do not explicitly take into account the ins
tallation of solar modules.
accumulate close by.
NOTE
In regions with particularly high snowfall, the
pressure load calculated in accordance with
the standard based on local snow load infor
dules.
SOLARWATT therefore tests its modules abo
accordance with additional standards, taking
into account additional loads in the event of
al loads encountered in practice and to ensure
that our products work safely throughout their
entire service life.
• Please take care when handling and in
and especially the corners are sensitive
to impact even though they are made of
•
surface
•
dules as a minimum. You should select a
zing is secured in place for the long term.
•
seals to mount the laminates which come
into contact with the embedded material
unless explicitly allowed by SOLARWATT.
• Make sure that the laminate edges do not
lie in accumulated water and are always
able to dry after exposure to rain or other
water.
NOTE
• the way of fastening
• the areas approved for fastening
• the maximum recommended pressure load on the modules*
Fixing by long side clamping
areas approved for fasteningsubstructure
Max. recommended pressure load to the module: 5,400 N/m²
Electrical connection and grounding
SOLARWATT solar modules are equipped at the
tors. The connection of the string line has to be
done with identical connectors manufacture
and type as to the module connecting cable. To
be able to ensure this the module connector at
the beginning and the end of the string may be
cable and instruction of the manufacturer have
to comply. The SOLARWATT pricelist contains
matching cablesets, plugs, cables and installati
on accessories. When connecting the modules,
ensure that the plugs engage with an audible
times the outer cable diameter must be com
plied with. It is recommended to lay the cable
nical loads. The cable and connector must not
exposed to moisture and will not rest on the
Solar modules generate electrical energy on the front side during incidence of light. A
dule is exposed to light.
WARNING
To ensure safety and compliance with the
technical data of the products, only original
tools of the manufacturer may be used in the
ted up to the maximum system voltage as listed
in applicable data sheet. The maximum num
ber of solar modules installed parallel without
string fuse is two. Please comply with the value
feed and only use standardized photovoltaic
wed to operate on a short circuit permanently.
The solar modules correspond to application
class II and can therefore be operated in sys
modules in this application class can be used in
systems with unrestricted access, the relevant
regulations must be complied with. SOLARWATT
requirements of protection rating II with correct
electrical installation.
higher voltage than under standardized test
ambient temperature for the given installation
location, to determine the rated voltage values
of components, the rated current values of con
ductors, the size of fuses and for dimensioning
control units connected to the solar modules.
Any type of soiling on the plug contacts befo
the system function over the intended service
period. For this reason it is necessary to pay
particular attention to cleanliness during ins
tallation. The use of lubricants is not permitted.
Always protect unplugged connectors against
soiling of any type during transport, storage,
and during installation, as the connectors only
satisfy the requirements for their protection ca
tegory when plugged in. It is forbidden to open
the junction box or modify or remove the cable.
The cables must be laid so that mechanical
strain on the conductors and connections is ru
relevant data sheets at www.solarwatt.com.
The plug contacts must not be connected or disconnected under load. Failure to comply
WARNING
It is advisable to install lightening protection in exposed locations. The solar modules
should be incorporated in existing lightening protection equipment. For this, take into
NOTE
Maintenance and servicing
A photovoltaic system needs practically no
maintenance, as the solar modules are cleaned
by the rain at the recommended minimum angle
wever, recommend carrying out a regular visual
check on the module surfaces. Particularly hea
reduce performance and should therefore be
intermixture and a soft nonabrasive cloth only.
In exceptional cases, a conventional cleaning
agent may also be used in the recommended
metal objects, as they can be particularly dama
ging to the hardened glass surface. The electric
Disposal
perly; they should never be disposed of with
domestic waste. The national disposal directive
must be observed. The disposal of solar modu
solar modules can be mostly returned in usual
commercial quantities to nearby municipal col
lection sites and local civic waste collection
State has its own legal regulations and practical
handling for the sale and return of PV modules.
and specify the number and type of modules to
be returned. We will then coordinate all further
details for returning your modules.
NOTES ON COMPLAINTS
If you still have cause for complaint despite the high quality of our products,
Table of contents
Other solarwatt Solar Panel manuals
solarwatt
solarwatt Vision 60M high power User manual
solarwatt
solarwatt Vision 60P style User manual
solarwatt
solarwatt BLACK 60M STYLE User manual
solarwatt
solarwatt EasyIn 60M Series User manual
solarwatt
solarwatt Vision 60P style User manual
solarwatt
solarwatt BLUE 60M User manual
solarwatt
solarwatt 36M glass User manual
solarwatt
solarwatt Vision 60M high power User manual
solarwatt
solarwatt Vision 60P style User manual
solarwatt
solarwatt Panel vision AM 3.0 User manual
Popular Solar Panel manuals by other brands
PION POWER
PION POWER PVSolver GS-03 installation manual
Jinergy
Jinergy JNMP60 series installation guide
Amerisolar
Amerisolar AS-6P18 installation manual
Panasonic
Panasonic VBHN225DJ06 General installation manual
Maurer Elektromaschinen
Maurer Elektromaschinen Summer Series manual
R3Di
R3Di RS200W user manual
Wasserstein
Wasserstein Solar Panel For Ring Video Doorbell 1 user manual
Polaroid
Polaroid SP50 instruction manual
Wansview
Wansview Solar Panel installation guide
Solarsol
Solarsol SSP27 user manual
SolarWorld
SolarWorld Kit Original instruction manual
Unical
Unical SOLECO 160 2.5 Installation, Use and Servicing Instructions
Hyundai
Hyundai UF Series manual
PREFORMED LINE PRODUCTS
PREFORMED LINE PRODUCTS POWER RAIL 60 Cell Assembly instructions
Taurus
Taurus PFB-0450-TG installation manual
ELITAL
ELITAL EL60/IS Setup instructions
Sharp
Sharp NU-JD545 installation manual
Photonic Universe
Photonic Universe 20A MPPT instruction manual