SolaX Power X1-0.6 User manual

IIII
II
Quick Installation Guide
X1 Series 0.6KW-3.6KW
Packing Lists
Inverter Installation
PV Connection
Note:
1) Please refer to the appropriate instruction manual for the usage of optional accessories.
2) For the optional accessories, please be subject to the actual delivery.
Female DC unit1
Male DC unit *1
Male DC unit1
Female DC unit*1
Inverter *1
Bracket * 1
- Unscrew the bracket from the back of the inverter.
- Mark the position of the two holes.
- Screw the expansion screws. - Match the inverter with the bracket.
- Screw the cross recessed screw on the right side.
- Drill holes with φ6 drill.
- Depth: at least 50mm.
- Tighten the expansion tubes.
200mm
Cable size: 4~6 mm²-Align the two halves connectors.
strip length:
7.0mm
Negative DC pin contact*1 Positive DC pin contact *1
Earth terminal 1 * AC Connector
positive DC
pin contact
male plug
nut female plug
tight nut
negative DC
pin contact
clamp contact
cable
Expansion tube*2
Self-tapping screw*2
X1 Series
User Manual
0.6kW - 3.6kW
Copyright Declaration
The copyright of this manual belongs to Solax Power Network Technology(Zhe jiang) Co,. Ltd.
Any corporation or individual should not plagiarize, partitially or fully copy (including
software,etc.), and no reproduction or distribution of it in any form or by any means. All rights
reserved. SolaX Power Network Technology (Zhe jiang) Co.,Ltd. reserves the right of final
interpretation.
Documents
Wi-Fi dongle (optional),
LAN/GPRS dongle (optional)*1

V
IV
Connections and Overview
Firmware Upgrading
AC Connection
1.Slide the cable nut andback shell onto the cable.
2.Insert the tripped end of each threewires into holes in the female
insert, then tighten each screw with L-type wrench.
trip length
52.5mm
6mm
55mm
outer jacket
5.Connect the AC plug to the inverter, and screw down the pressure
screw on the top part of AC terminal.
4.Screw down the pressure screw.
3.Screw down the threaded sleeve of the pressure screw.
- Overview for connection.
- After checking all connections are correct, turn on the external
DC /AC breakers.
- Inverter will start automatically when PV panels generate
enough energy. The LED will be blue and the LCD screen
will display the main interface.
- Turn on the DC switch to the “ON” position.
320102024801
Firmware Upgrading
For the inverter with LCD, user can refer to the following:
Ø
– After the upgrade is complete, please pull off the USB flash drive, and then screw the panel of DONGLE port.
* Please contact our service support to get the update package, and extract it into your USB flash drive.
Please DO NOT modify the program file name! Otherwise it may cause the inverter not work anymore !
- Download the upgrade program into USB flash drive.
ARM
DSP
Cancel
OK
Update(ARM)
Updating----25%
Update(ARM)
>618.00207.00... ...
ARM
DSP
Update(DSP)
Updating----25%
Update(DSP)
>618.00381.00... ...
- Insert the USB flash drive with program into the “DONGLE” port on the bottom.
L,N cable(mm²) Inverter+BMU
X1-0.6/0.7/ /1.1 1.5
Model X1-2.0
Micro-breaker 10A 16A
PE cable(mm²)
2.5-6 2.5-6
2.5-6 2.5-6
X1-2.5/3K/3.3K
20A
2.5-6
2.5-6
X1-3.6K
20A
2.5-6
4-6
- Screw the ground screw with Φ4 hexagon wrench shown as follow.
- Prepare the connector and the communication cable, following the PIN
definition and assembly order bellow, then insert the cable into the
corresponding RS485 portof the inverter, and tighten the waterproof
1
8
PIN
Definition
1 4
Meter_A/
7
E_Stop
5
Meter_B/
8
RefGen
2
Com/DRM0
3
GND_COM
6
CT-
485_A 485_B
CT+
CT/DRM/Meter/RS485
CT
L line
Public grid
→
AC port
arrow point to
the public grid
RS485 port DRM/Meter/RS485
Torque:1.5±0.2N.m
Torque:1.2±0.1N.m
connector.
- Please contact the service to get the latest firm -Please contact Solax service to get the latest firmware. Then add a
new folder named "Update" in the root directory on your Udisk,
and two more sub-folders named "ARM" and "DSP" under "Update". Please copy the firmware files into ARM and DSP
respectively. It will be like:
update\ARM\618.00207.00_X1_BOOST3.0_MINI2.0_AIR2.0_ARM_V1.21_20200826.usb;
“update\DSP\618.00381.00_X1_BOOST3.0_MINI2.0_AIR2.0_DSP_V2.03_20201117.usb
Press and hold the “Enter” key for 5 seconds to enter Off Mode. Then unscrew the waterproof lid and insert the U-disk
into the "upgrade" port.
- When the user turns on all the switches, the LCD will show pictures as bellow.
And at the same time, the user can choose the program you need by short pressing “ ” and “V” key , and then long
press “V” to confirm and upgrade the inverter.