Soleus Air HCB-P11-A User manual

 BTU Portable Air Conditioner with
Evaporative Technology
Operating Instructions
Model No.: HCB-P11-A
3092402
Reference No.: BPA11
V.140204

Thank you for choosing a Soleus Air Portable Air Conditioner. This owner’s manual will provide you
with valuable information necessary for the proper care and maintenance of your new product. Please
take a few moments to thoroughly read the instructions and familiarize yourself with all the operational
aspects of your new Soleus Air Portable Air Conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the store
name/location, date purchased, and serial number below:
Store Name: ____________________________________________________
Location: ______________________________________________________
Date Purchased: _________________________________________________
Serial Number (located on back of unit): ______________________________
2
IMPORTANT INSTRUCTIONS
Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this
manual in a safe place for future reference.
1) Always place the unit on a level surface.
2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual.
3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or outlet
grilles.
4) The unit must be connected to a correctly grounded power supply.
5) Do not start or stop the unit by inserting or pulling out the power plug.
6) Do not use an adapter plug or extension cord.
7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.
8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this manual.
9) Do not let children play near this unit.
10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced by the
manufacturer or a qualified service technician.
11) When cleaning the unit, always turn the unit off and unplug the power cord.
12) When the unit is not in use, always remove the venting kit from window.
13) Do not mix old and new batteries. Do not mix alkaline, standard (carbon - zinc), or rechargeable (nickel –
cadmium) batteries.

3
SPECIFICATIONS
 The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.
 The operational ambient temperature is between 61°F ~ 109°F.
 Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode.
 Power consumption is measured when the fan runs at the highest speed setting.
 These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.
 If the ambient temperature is higher than the max operating temperature or lower than the minimum operating tem-
perature, the air conditioner may not work properly.
PACKAGE CONTENTS
Portable Air Conditioner (1)
Exhaust Hose (1)
Hose Adapter (1)
Window Kit Adapter (1)
Remote Control (1)
AAA Batteries (2)
Window Kit - 3 Sliding Panels (1 single hose panel, 2 extension panels)
Owner’s Manual (1)
MODEL / REFERENCE NUMBER HCB-P11-A / BPA11
COOLING CAPACITY 11,000 Btu/Hr
DEHUMIDIFIER CAPACITY 48 Pints/Day
AIR FLOW VOLUME 225 CFM
POWER SOURCE 115 V / 60 Hz
RATED CURRENT 9.3 Amps
SOUND PRESSURE LEVEL 46 dB(A)
NET WEIGHT 56 Lbs
PRODUCT DIMENSIONS (W x D x H) 11.75”W x 18.25”D x 24.625”H
REFRIGERANT R-410A
COOLING POWER CONSUMPTION 1060 Watts

4
LCDI POWER CORD AND PLUG
This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord
and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-
ble cord with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined
value. The cord will remain de-energized until the devise has been manually reset. This is intended to re-
duce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded
and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground
or to any exposed metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet. The LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,
3. Press RESET button to restore power to the machine. Once power is restored, the LED light
will turn on again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the
air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting
recommendations.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for indoor use only.
LED LIGHT
the LED light will turn off.
Note: Your units power cord and plug may differ from the one shown.

PRODUCT DIAGRAM
Casters
Louvers
Control Panel and
LED display
Air Filter Compartment
and Air Intake
5
Air Filter Compartment
and Air Intake
Power
Cord Wrap
Remote Control
Holder
Exhaust Outlet
Drain
Plug
Carry Handle
Power Cord

6
PARTS & ASSEMBLY
PARTS
EXHAUST HOSE
WINDOW KIT
ASSEMBLY & INSTALLATION
INSTALLATION
When the unit is operating as an air conditioner, or dehumidifier, the unit draws in fresh outdoor air and exhausts hot air
out of the room to complete the air exchange.
NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors from 14 inch up to
55.5 inch long.
MOUNTING THE EXHAUST HOSE
 Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove
packaging and locate components.
 Extend both ends of the exhaust hose approximately 6 inches.
 Screw the window kit adapter onto one end of the exhaust hose counter-clockwise. Screw the hose
adapter onto the other end of the exhaust hose counter-clockwise.
 Slide the hose adapter of the exhaust hose down arrow over the discharge opening on the back of the unit.
 Open the window or door and adjust the length of window kit to fit the opening. Then make the kit fixed.
 Attach the window kit adapter of the exhaust hose to the window kit.

WINDOW KIT INSTALLATION
Installation of the Venting Kit
FOR SINGLE HOSE PORTABLE AIR CONDITIONERS
The venting kit must be installed in order for the unit to
work correctly in the air conditioning mode. The venting
kit should not be used while the unit is heating or
fanning.
The window kit has been designed to fit into most
vertical and horizontal window openings. The window kit
can also be used in a sliding door.
1. Choose a suitable location, near a grounded
electrical outlet and a suitable window or door.
Remove packaging and locate components. (Figure
A)
2. Slide the exhaust connector over the discharge
opening on the back of the unit. (Figure B)
3. Connect the exhaust hose to the exhaust connector,
aligning the fitted grove.(Figure C)
4. Open the window or door and adjust the length of
the window kit to fit the opening. (Figure D) If
necessary, mark the kit and cut one end down to
properly fit the opening. (Figure E&F)
5. Attach the window kit adapter to the window kit.
(Figure G)
6. Place the window kit back into the window and
attach the exhaust hose to the window kit adapter.
(Figures H & I) Close the window tightly. (Figure J)
Your portable Air Conditioner is now ready to cool!
NOTE: When using the venting system, keep the exhaust
hose as straight as possible. The exhaust hose can be
shortened, but it is not recommended to increase the
length of the exhaust hose. Do not use an extension
cord with your portable air conditioner.
Optional Window Kit Adapter Extension (Included)
The Window Kit Adapter Extension is an optional part
that can be used on window sizes that require a longer
connection between the window and the exhaust hose.
NOTE: The Portable Air Conditioner above may differ from the unit described in this manual. The above directions and
images show general directions for Soleus Air hose portable air conditioners.
7

WINDOW KIT ASSEMBLY
1.Parts:
A) 2 Track Screws
B) 2 Wing Nuts
C1 & C2) 2 Hose Panels, one Exhaust Hose Openings
D) 1 Sliding Track Panel
2. Assembly:
First, take the Track Screws (A) and screw one
into each of the small holes found on the Hose
Panels (C1 & C2).
3. Next, take the Wing Nuts (B) and tighten them
around each of the Track Screws (A). Do not tighten
the Wing Nuts (B) all the way; make sure they are
somewhat loose.
4. Now, place the Sliding Track Panel (D)
over the Track Screw (A) on Hose Panel (C1).
5. Next, take the other Hose Panel (C2) and connect
it to Hose Panel (C1) by placing the Sliding Track
Panel (D) over the Track Screw (A) on Hose Panel
(C2).
6. The Hose Panels (C1 &C2) should now be
connected using the Sliding Track Panel (D).
7. To complete the assembly, tighten the wing Nuts
(B) installed earlier. The finished Window Kit
should resemble the image seen below.
8

CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS
CONTROL PANEL
TEMPERATURE
AND TIMER
INDICATOR
9
FAN SPEEDMODE
TIMER/TEMP DECREASE
POWER
TIMER/TEMP INCREASE
TIMER
OPERATING INSTRUCTIONS
1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER
button once more to turn the unit off.
2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Air Condi-
tioner and Dehumidifier.
3) Fan Speed Control - Press the FAN Button to cycle through the different fan speeds: High and low.
4) Temperature - Select the desired temperature by pressing either ▼or ▲ key when using the unit in
cooling mode. The temperature indicator flashes to display the desired temperature setting. After the tem-
perature is set, the unit will display this temperature setting until it is changed by the user. The temperature
indicator display shows temperature in Celsius or Fahrenheit. Press the ▼and ▲simultaneously to
change between Celsius and Fahrenheit .
5) Auto-on Timer- To program the Auto-on timer, press the TIMER button when the unit is powered off.
Once the TIMER button is pressed the hours will blink on the display. Press the ▼or ▲ buttons to
change the number to the desired hours (1-24 hours) for the unit to automatically turn on. The timer is set
when the TIMER stops flashing.
6) Auto-off Timer- To program the Auto-off timer, press the TIMER button when the unit is powered on.
Once the TIMER button is pressed the hours will blink on the display. Press the ▼or ▲ buttons to
change the number to the desired hours (1-24 hours) for the unit to automatically turn off. The timer is set
when the TIMER stops flashing.
NOTE: Heat mode is not available on this model.
- Press the POWER button once to manually turn the unit on. Press the POWER
button once more to turn the unit off.
2) Mode Selection
$LU&RQGLWLRQHUPRGHRQO\

10
OPERATING THE UNIT USING THE CONTROL PANEL
Air Conditioner Mode
1) Install the exhaust hose and window kit properly (see pages 7 & 8 ).
2) Plug the Power Cord into an electrical outlet.
3) Turn on the unit by pressing the POWER button on the control panel.
4) Press the Mode button until the led of AIR CONDITIONER light up on the control panel display.
5) Press the ▲or ▼buttons until the desired room temperature appears on the control panel display. The
temperature ranges from 61°F - 88 °F (16 °C - 31 °C).
6) Select the desired fan speed by pressing the FAN button.
NOTE: During hot days, the unit will cool the room most efficiently by setting the temperature at the lowest
setting and the fan speed on high. Reducing the length of the exhaust duct, insulating the exhaust hose and
window kit, and keeping direct sunlight to a minimum will also improve the cooling efficiency.
NOTE: When the unit is running on cooling mode, the exhaust hose is required and must be vented outside
using the supplied window kit.
Dehumidifier Mode
1) Install the exhaust hose and window kit properly (see pages 7 & 8 ).
2) Plug the Power Cord into an electrical outlet.
3) Turn on the unit by pressing the POWER Button on the control panel.
4) Press the MODE button until the led of DEHUMIDIFIER light up on the control panel display.
5) change the direction of the air flow manually adjust the horizontal louvers up or down.
NOTE: The unit operates at low fan speed during dehumidifier mode. The unit cools room slightly during
while dehumidifying. Keep the windows and doors closed to aid the effectiveness of the unit as it removes
moisture from the room.
NOTE: When the unit is running on dehumidifier mode, the exhaust hose is required and must be vented
outside using the supplied window kit. The unit will not perform in dehumidifier mode when the room tem-
perature is lower than 61°F .
Compressor Indicator
The COMPRESSOR LED will light up on the control panel display when the compressor turns on. The LED of
COMPRESSOR will turn off when the compressor shuts off.