Soleus Air HCC-C09H26-A User manual

As a professional installer you need to know the product better than the customer. This instruction includes all safety precautions and related items. Prior to actual installation, thoroughly familiarize yourself with this instruction manual. Pay special attention to all safety warnings. During installation or maintenance, it is possible to be in a position which is more hazardous than when the unit is in operation.Remember it is your responsibility to install the product safely and to know it well enough to be able to instruct a customer in its safe use.Safety is a matter of common sense, a matter of thinking before acting. Most dealers have a list of specific good safety practices, follow them.The precautions listed in this Installation Manual are intended as ractices. However, if there a direct conflict between existing practices and the content of this manual, the precautions listed here take precedence.supplements to existed pATTENTION INSTALLATION PROFESSIONALPACKAGED TERMINAL
AIR CONDITIONER
Installation and Operating Instructions
Model No.:
HCC-C09H26-A
HCC-C12H26-A
4004987
V170303

CONTENTSIMPORTANT TO THE OWNER2IMPORTANTTO TTRANSPORTATION DAMAGE 2INSTALLATION INSTRUCTIONS MONTHLY MAINTENANCE AND CLEANINGWIRNGUNIT FEATURES89AUXILIARY CONTROLS-DIP SWITCHESNORMAL OPERATING SOUNDS AND CONDITIONSTROUBLE SHOOTING NOTES …………………… NOTES HE SERVICER… ………………2… …………………………2UNPACKING THE UNIT… …………………………………2OPERATING INSTRUCTIONS………………………………… ……………………3………………6I… …………………………………………………7…………………………………………………OPERATING INSTRUCTIONS………………………………………………11……12ERROR CODES………………………………………………12…………………………………13-1-RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION
WARNING
HIGH VOLTAGE DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE F AILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.PRESENTED, THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY INJURY OR ARISING FROM IMPROPER SERVICE OR SERVICE PROCEDURES. IF YOU INSTALL OR PERFORM SERVICE ON THIS UNIT, YOU ASSUME RESPONSIBILITY FOR ANY PERSONAL INJURY OR PROPERTY DAMAGE WHICH MAY RES ULT, MANY JURISDICTIONS REQUIRE A LICENSE TO INSTALL OR SERVICE HEATING AND AIR CONDITIONING EQUIPMENT.PROPERTY DAMAGE
WARNING
IMPORTANT NOTES: Before using this manual, check the serial plate for proper model identification. The installation and servicing of this equipment must be performed by qualified, experienced technicians only.Due to policy of continual product improvement, the right is reserved to change specifications and design without notice.THE FOLLOWING WARNINGS ARE VERY IMPORTANT FOR SAFETY. PLEASE READ THEM CAREFULLY BEFORE INSTALLATION!1. The air conditioner must be installed by certific2. Please check whether there installation. If not, instfety principle to users.3. To avoid electric shock or even death, the socket or terminal blocks for power suppseries and the units that have LCDI power cord) must conna Ground Fault Circuit Interrupter.4. During installation,the wire connection must strictly follow theconnected to the zero line and fire line in the power system. The connection in reverse is forbidden. Pleawire is firmly connected otherwise it is possible to result in the electrical shock or death.ated install ers. It's forbidden to install by those amateurs.is ground wire in the power supply system before allers should refuse to install and explain the saly of the air conditioner(include 277V, 115V, 208V~230V ect to rule that zero line and fire line of the unit should be se make sure the ground OPTIONAL ACCESSORIESWall Sleeve Kit Filter KitStamped Louver KitLCDI Power CordIR Remote ControllerNOTE: Refer to sales literature for the appropriate voltage and amperage selections.

-2-OPERATING INSTRUCTIONSThis unit has many fece the unit .atures which are different from those found on conventional units. The servicer must be familiar with these features in order to properly servi• LCDI Cords-Underwriters Laboratories and the National Electric Code (NEC) now require power cords rent leakage and open the electrical circuit to the unit on units rated at 250 volts or less. In the event that unit does not operate, check the reset button located on or near the head of the power cord as part of the normal troubleshooting procedure.that can sense curCheck the data specification plate and ensure the proper voltage and current rating for the type of plug on the unit is available. DO NOT REMOVE THE GROUNDING PRONG FROM THE POWER CORD. See Fig 1 for the types of acceptable plugs. Do not use an extension cord for the installation of this product. to the data specification plate for electrical requirements.ReferFig 1
240V18 Amp
120V15 Amp
240V15 Amp
LCDI Power CordVOLTAGE MEASUREMENTSBefore connecting the unit, measure the supply voltage. Voltage must within the voltage utilization range given in Table1.Operating VoltageVoltage Utilization RangeMinimumMaximumUnit Voltage Rating230/208115187253103126Table 1IMPORTANTconsidered as supplemental information.T NOTES TO HE SERVICER Read this manual and familiarize yourself with the specific items which must be adhered to before attempting to service this unit. The precautions listed in this manual should not supersede existed practices but should be IMPORTAHE OWNER This equipment is to be serviced b trained personnel only. If this equipment is improperly installed, adjusted or altered by an unqualified person, a safety hazard may result. NT NOTES TO Ty professional andAll units are securely packed in shipping containers approved by the National Safe Transit Association. The carton should be checked upon arrival for external damage. If damage is found, make a written request for inspection immediately by the carrier’s agent.In the event of damage: UNPACKING THE UNIT1. Cut the carton banding and open the carton.2. Remove the literature, hardware pack, upper styrofoam shipping blocks, and styrofoam corner posts.3. Remove the front assembly.4. Lift the unit from the remaining carton.5. Dispose of the cardboard and styrofoam at an approved Recycle Center. Check all contents for damaged or missing parts. TRANSPORTATION DAMAGE1. Note on the 2. Notify carrier promptly and request an inspection. 3. File the claim with the following supporting documentswithin the six month statute of limitations. delivery receipt about any visible damage to shipment or container.The carrier is responsible for making prompt inspection of damage and for a thorough investig claim. The distributor or manufacturer will not accept claims from dealers for transportation damage.ation of each a. Original Bill of Lading, certified copy, or indemnity bond.b. Original paid freight bill or indemnity.c. Original invoice or certified copy, showing trade and other discounts or reductions.d. Copy of the inspection report issued by carrier’srepresentative at the time damage is reported to the carrier.In case of concealed damage, notify the carrier as soon as possible-preferably within 5 days. Refer to step 3 of the Transportation Damage section if damage or missing parts are noted.