Soleus Air PSX-08-01B User manual

V181219
3058080
Air conditioner must be upright for 24 hours prior to operating.
This ensures that the compressor will function as intended.

Thank you for choosing a Soleus Air Portable Air Conditioner. This Owner’s Manual will provide
you with valuable information necessary for the proper care and maintenance of your new product.
Please take a few moments to thoroughly read the instructions and familiarize yourself with all the
operational aspects of your new Soleus Air Portable Air Conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the
store name/location, date purchased, and serial number below:
Store Name: ____________________________________________________
Location: _____________________________________________________
Date Purchased: _________________________________________________
Serial Number (located on back of unit): ______________________________
Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this
manual in a safe place for future reference.
1) Always place the unit on a level surface.
2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual.
3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or outlet
grilles.
4) The unit must be connected to a correctly grounded power supply.
5) Do not start or stop the unit by inserting or pulling out the power plug.
6) Do not use an adapter plug or extension cord.
7) Do not use the unit directly by a bathtub, shower or swimming pool.
8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this
manual.
9) Do not let children play near this unit.
10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced by
the manufacturer or a qualified service technician.
11) When cleaning the unit, always turn the unit off and unplug the power cord.
12) Do not mix old and new batteries in the remote control.
Do not mix Alkaline, Standard (Carbon - Zinc) or Rechargeable (Nickel - Cadmium) Batteries.
IMPORTANT INSTRUCTIONS
PURCHASE INFORMATION

Model Number PSX-08-01B PSX-10-01B PSC-12-01B PSC-14-01B
Cooling Capacity 8,000 BTU/Hr 10,000 BTU/Hr 12,000 BTU/Hr 14,000 BTU/Hr
Dehumidification 86 pts/Day 107 pts/Day 120 pts/Day 120 pts/Day
Cooling Power
Usage
938 Watts
8.2 Amps
1160 Watts
10.1 Amps
1385 Watts
12 Amps
1545 Watts
13.5 Amps
Air Flow (H/M/L) 176/155/132 CFM 176/155/132 CFM 223/206/188 CFM 241/217/176 CFM
Power Source 115 V / 60 HZ 115 V / 60 HZ 115 V / 60 HZ 115 V / 60 HZ
Noise Level dB(A) 52-54 52-54 53-55 53-55
Product Weight 51.8 Lbs 54 Lbs 65 Lbs 66.1 Lbs
Operating
Temperature 61℉-88℉61℉-88℉61℉-88℉61℉-88℉
Product Dimension
(W x H x D) 17.125”×27.125”
×12.375”
17”.125×27.125”
×12.375”
17.5”×28.75”×
14.5”
17.5”×28.75”×
14.5”
Refrigerant R-410A R-410A R-410A R-410A
Portable Air Conditioner (1)
Exhaust Hose (1)
Exhaust Hose Connector (1)
Window Kit Panel (2)
Window Kit Adapter (1)
Window Kit Adapter Grille (1)
*8,000 & 10,000 BTU Only
Optional Window Kit Adapter Extension (1)
Wing Nut (1)
Optional Drain Tube (1)
Drain Tube Stopper (1)
Remote Control (1)
AAA Battery (2)
Owner’s Manual (1)
Optional Window Security Pack (1)
PACKAGE CONTENTS
SPECIFICATIONS
• The cooling capacity is measured at an ambient temperature of DB 95˚F, WB 83 ˚F.
• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cool-
ing mode.
• Power consumption is measured when the fan runs at the highest speed setting.
• These specifications are for reference only. For actual data, please refer to the rating label on the back
of the unit.
• If the environment temperature is higher than the max operating temperature or lower than the minimum operat-
ing temperature, the air conditioner may not work properly.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord
and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flex-
ible cord with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined val-
ue. The cord will remain de-energized until the device has been manually reset. This is intended to reduce
the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded
and they must be considered a shock hazard if exposed. The cord shield must not be connected to ground
or to any exposed metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet, the LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,
the LED light will turn off.
3. Press RESET button to restore power to the unit. Once power is restored, the LED light will
turn on again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the
air conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting recom-
mendations.
Note: Your unit’s power cord may
differ from the one shown.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for indoor use only.
RESET
TEST
POWER CORD AND PLUG

PRODUCT DIAGRAM
1. Control Panel
2. Manual Control Louver & Air Outlet
3. Carry Handle
4. Casters
5. Air Filter
6. Continuous Drain Port
7. Air Discharge Opening
8. Air Intake Grille
9. Condensation Drain Hole
10. Exhaust Hose
11. Exhaust Hose Connector
12. Window Kit Adapter Grille
13. Window Kit Adapter
14. Optional Window Kit Adapter Extension
15. Window Kit Panels
16. Wing Nut
17. Optional Drain Tube
18. Drain Tube Stopper
19. Remote Control
20. Batteries
21. Optional Window Security Pack
MODEL# PSX-08-01B/PSX-10-01B

1. Control Panel
2. Manual Control Louver & Air Outlet
3. Carry Handle
4. Casters
5. Air Filter
6. Continuous Drain Port
7. Air Discharge Opening
8. Air Intake Grille
9. Condensation Drain Hole
10. Exhaust Hose
11. Exhaust Hose Connector
12. Window Kit Adapter
13. Window Kit Panels
14. Optional Window Kit Adapter Extension
15. Wing Nut
16. Drain Tube Stopper
17. Optional Drain Tube
18. Remote Control
19. Batteries
20. Optional Window Security Pack
PRODUCT DIAGRAM MODEL# PSC-12-01B/PSC-14-01B

WINDOW VENTING KIT
OPTIONAL WINDOW SECURITY BRACKET
ASSEMBLY & INSTALLATION
When the unit is operating in air conditioning mode, the unit draws in indoor air and exhausts hot air out of the room
to complete the air exchange. The Window Kit must be installed when operating the unit in air conditioning, dehu-
midification. When the unit is operating in Fan Mode, no outdoor air exchange takes place. The window kit and ex-
haust hose do not need to be installed when the unit is used as a fan.
The supplied window kit can be installed in sliding windows and sliding glass doors up to 7 ft. long
(approximate length). When installed, be sure to keep the exhaust hose as short and straight as possible for
maximum efficiency.
PARTS & ASSEMBLY
*8,000 & 10,000 BTU Only

.
WINDOW KIT ASSEMBLY
1. Unscrew the Wing Nut from the base. Insert the Wing
Nut base into the small hole found on panel A
2. Screw the Wing Nut onto the Wing Nut Base until
slightly loose. (Will tighten in an upcoming step.)
3. Slide panel B inside panel A and over the
Wing Nut Base.
5. Tighten Wing Nut to secure both panels.
4. Panel A and B should now be connected.

.
PORTABLE AIR CONDITIONER
The window venting kit must be installed in order for the unit to work correctly. The window venting kit has been de-
signed to fit into most vertical and horizontal window openings and sliding glass doors up to 7 feet.. *The window kit
included with your purchase may vary slightly from what is shown below.
2. Twist the Exhaust Hose Connector
onto Exhaust Hose.
1. Open the window or door to adjust the length of the Window
Kit Panels to fit the opening. If necessary, mark the kit and cut
one end down to properly fit the opening.
3. Twist the Exhaust Hose Connector over the discharge opening
on the back of the unit and extend the Exhaust Hose. (Keep the
exhaust hose as short and straight as possible)
4. Attach the Exhaust Hose to the Window Kit Adapter. Now connect
the Optional Window Kit Adapter Extension to the Window Kit Adapt-
er. Then attach the Optional Window Kit Adapter Extension to the
Window Kit panel. Close the window or door tightly.
WINDOW KIT INSTALLATION
Keep the exhaust hose
as short and straight as
possible for maximum
efficiency.

Optional Security Bracket Installation
Your Window Kit also includes an optional security bracket that can be installed to prevent the window from being
opened from the outside while a Window Kit is installed.
SECURITY BRACKET
Single and Double Hung Windows
Sliding Windows