Soleus Air WS4-06EW-201 User manual

4010450
V210127
Air conditioner must be upright for 24 hours prior to operating.
This ensures that the compressor will function as intended.
Model
WS4-06EW-201 6,000 BTU
WS4-08EW-201 8,000 BTU
Electronic Hybrid Air Conditioner
Operating Instructions

Thank you for choosing a Soleus Air Hybrid Air Conditioner. This Owner’s Manual will provide
you with valuable information necessary for the proper care and maintenance of your new product.
Please take a few moments to thoroughly read the instructions and familiarize yourself with all the
operational aspects of your new Soleus Air Window Air Conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the
store name/location, date purchased, and serial number below:
Store Name: ____________________________________________________
Location: _____________________________________________________
Date Purchased: _________________________________________________
Serial Number (located on back of unit): ______________________________
IMPORTANT INSTRUCTIONS
PURCHASE INFORMATION
Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a
safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to
all safety messages outlined in this owner’s manual.
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove the ground prong.
• Do not use a plug adapter.
• Do not use an extension cord.
• Unplug the air conditioner before servicing.
• Use two or more people to move and install the air
conditioner.
This is a safety alert symbol.
This symbol alerts you to potential hazards that can harm you or others or even cause death.
All safety messages will directly follow the safety alert symbol and/or the words “DANGER”
or “WARNING.”
All Safety messages alert you of potential hazards, how to reduce the chance of injury, and what
can happen if instructions are not followed correctly.
Failure to immediately follow these in-
structions may cause serious injury or
even death.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord
and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-
ble cord with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.
The cord will remain de-energized until the device has been manually reset. This is intended to reduce the
risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they
must be considered a shock hazard if exposed. The cord shield must not be connected to ground or to any
exposed metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly.
To test:
1. Plug power cord into wall outlet, the LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs, the LED
light will turn off.
3. Press RESET button to restore power to the unit. Once power is restored, the LED light will turn on
again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air
conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting recommenda-
tions.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for
indoor use only.
POWER CORD AND PLUG
RESET
TEST
LED LIGHT
Note: Your unit’s power cord may
differ from the one shown.

PACKAGE CONTENTS
Air Conditioner
(2) - Mounting Block
• Hybrid Air Conditioner (1)
• Remote Control (1)
• AAA Battery (2)
• Window Slider Foam (2)
• Mounting Block (2)
• Window Slider Support Bracket (2)
• Pre-installed Adjustable Support Knob (2)
• Top Foam Sealer (1)
• Bubble Level (1)
• Optional Window Security Bracket
- Security Bracket (1) , Type B Screw (1)
• Owner’s Manual (1)
Remote
Control
2 AAA
Batteries
Top Foam
Sealer
Owner’s Manual
(2) - Window Slider Support Bracket
(2) - Window Slider Foam
(1) - Security Bracket
(1) - Type B Screw (2) - Pre-installed Adjustable Support Knob
Bubble Level

SPECIFICATIONS
• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.
• Power consumption is measured when the fan runs at the highest speed setting.
• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.
Model WS4-06EW-201 WS4-08EW-201
Power Supply (Ph/V/Hz) 1/115/60 1/115/60
Rated Cooling Capacity (BTU/h) 6,000 8,000
Cooling Power Input (Watts) 495 667
Rated Current Cooling (Amperage) 4.5 6.5
CEER 12.1 12.0
Noise Level (dB(A)) 38-49 (Indoor) / 51-63 (Outdoor) 38-49 (Indoor) / 51-63 (Outdoor)
Airflow CFM 170/230/270 165/223/264
Dehumidifying Capacity 30 Pints per day 34 Pints per day
Product Dimensions (W” x H” x D”) 18.7” x 15” x 28.9” 18.7” x 15” x 28.9”
Package Dimensions (W” x H” x D”) 20.4” x 17.3” x 30.8” 20.4” x 17.3” x 30.8”
Net/Gross Weight (lbs) 67.7/80 71.2/83
Refrigerant Type R-410A R-410A
Plug Type NEMA 5-15P NEMA 5-15P
FCC Notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the device and receiver
Connect the device into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/television technician for help .
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equip-
ment. Such modifications could void the user’s authority to operate the equipment.

ELECTRICAL SAFETY
WARNING:
grounding prong!!
Power supply cord with 3-prong grounding
plug and current detection device
DISCLAIMER
ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE
PRESENATION OF THE MANUFACTURER. NEPO USA HAS NOT CONDUCTED AN INDEPENDENT TEST TO
VERIFY THE INFORMATION AND SPECIFICATIONS PRESENTED HEREWITHIN.

INSTALLATION
Window Preparation
Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If a new
electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.
Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made to fit
inside a standard double-hung window. Make sure the window is in good shape. If not, make repairs prior to installing the unit.
Storm Window Requirements
A storm window frame will not allow the air conditioner to tilt properly which will keep it from draining properly. To
adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.
Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air
conditioner to tilt enough for proper drainage (See FIG. 2).
Prior to Installing the Air Conditioner
1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,
or awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.
2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate
(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to
reach.
3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-
ing. Due to the large size of this air conditioner, two people should move the unit together.
When handling the unit, be careful to avoid cuts from the
sharp metal edges and aluminum fins on the front and rear
coils.
16" MIN
FIG .2
FIG. 1
16" MIN
Model WS4-06EW-201 WS4-08EW-201
Unit Height 15” 15”
Unit Width 18.7” 18.7”
Min. Window Opening 16” 16”
Min. Window Width
(Including space needed for window slider) 24" 24"
Max Window Width 48" 48"
Max Window Sill t 11” 11”

1. Attach Mounting Blocks on Window Frame (See Fig.1)
1) Remove adhesive from mounting block and place mounting block on
window frame.
2) Press down firmly on the mounting block to secure in place.
3) Then, remove adhesive from the other mounting block and place
mounting block on window frame.
4) Press down firmly on the mounting block to secure in place.
5) The mounting block are now ready to support the Hybrid Air Condi-
tioner.
2. Slide Hybrid Air Conditioner Over Window Sill
1) Open window completely
2) Lift the Hybrid Air Conditioner on either side of the unit and bring it up to the window.
3) Insert the unit into the window until the center of the Hybrid Air Conditioner is over the window sill.
4) Slowly lower the Hybrid Air Conditioner over the window sill so that the unit straddles the wall.
5) Paying close attention to your fingers, completely lower the Hybrid Air Conditioner onto the window sill.
6) Center Hybrid Air Conditioner in the window so that there are equal gaps on either side of the unit.
*Use the adjustable supports to secure the Hybrid AC against
the outside wall. (See Fig.2)
*Use the bubble level to make sure the unit is balanced
when secure on the window sill. When balanced, the bubble should
between the two black lines. (See Fig.3)
3. Attach Window Slider Support Brackets (See Fig.4)
1) Remove adhesive from window slider support bracket.
2) Position support bracket (adhesive-side) against the left-side edge of the Hybrid Air Conditioner at the
point where the window sash will be aligned with the support bracket when closed.
3) Press the support bracket firmly in place and hold for 5 seconds.
4) Repeat these steps on the right-side edge of the Hybrid Air Conditioner.
INSTALLATION
Fig.1
Fig.2
Fig.4
Fig.3

INSTALLATION
4. Install Window Sliders
1) Measure the distance between the Hybrid AC and the window sash, cut window slider foams to length by
using a utility knife so that it fits inside the opening. (See Fig.5)
2) Slide window slider foams into both support brackets on either side of the Hybrid Air Conditioner. (See
Fig.6)
5. Attach Top Foam Sealer
1) Measure the total width of the installation including the window sliders
2) Cut the top foam sealer to length
3) Remove adhesive from the top foam sealer
4) Attach the top foam sealer to the top of the Hybrid Air Conditioner and
window sliders directly below the window sash
5) Close the window sash and seal.
6. Plug in Hybrid Air Conditioner and Power ON
Fig.5
Fig.6
Fig.7
END OF SEASON
Remove the Air Conditioner from the Window (End of Season)
1. Turn the air conditioner off, and disconnect the power cord.
2. Remove the window sliders from either side of the air conditioner.
3. Using a drain pan, unplug the drain plug on the front bottom of the unit to drain any condensation water
in the base of unit.
4. Keeping a firm grip on air conditioner, lift up and remove the air conditioner from the window and
sill.
5. Store parts with the air conditioner in the box.
Single and Double Hung Windows
SECURITY BRACKET
Optional Security Bracket Installation
Your Window Kit also includes an optional security
bracket that can be installed to prevent the window
from being opened from the outside while a Window
Kit is installed.

WIFI APP SETUP *Screenshots shown are from an Apple iOS device. Android devices may differ slightly.
Step 1
Search and download Soleus
Home Comfort from the App
Store or Android Store
Step 2
Register for a new account
Step 3
Fill out email address and click the Get Verifi-
cation Code button. (Email will be sent with
confirmation instructions)
Step 4
Login with username and
password and click add
device
Step 5
Choose Large Home Appliances
and Air Conditioner (Wi-Fi)
Step 7
DO NOT TURN ON THE DEVICE.
Hold the Timer button over 3 seconds
until the Wi-Fi indicator is flashing on
the control panel
Step 6
Enter the Wi-Fi name and Password
Step 8
Click Done and all set
Step 9
To use the voice commend function,
click the Pen icon on the right corner
To reset the Wi-Fi module, hold down the
Timer buttons for over 3 seconds until the
beeping sound is heard.
Note: If the device name is unable to be
found from the network list or the device is
un-registered from the APP, the Wi-Fi
module needs to be reset.