SOMFY WireFree RTS Assembly instructions

Ref. 5066683A
EN Installer Guide
ES Manual para instalador
PT Guia do Instalador
EL 

www.somfy.com
Sunis indoor
WireFree™ RTS

Somfy hereby declares that this product conforms to the essential
requirements and other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity is available at www.somfy.com/ce. Images are
not contractually binding.
Installation guide page 1
EN
Por la presente, Somfy declara que este producto cumple con los requisitos
básicos y demás disposiciones de la Directiva 1999/5/CE. Podrá consultar
una declaración de conformidad en la página web www.somfy.com/ce.
Las imágenes no son contractualmente vinculantes.
Guía de instalación página 15
ES
Pelo presente documento, a Somfy declara que o aparelho está em
conformidade com as exigências fundamentais e outras disposições
pertinentes da directiva 1999/5/CE. Está disponível uma Declaração de
Conformidade em www.somfy.com/ce. As imagens não têm vinculação
contratual.
Guia de instalação página 29
PT
 
EL

         
       


Installation guide
1
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
1. Introduction 2
2. Safety 2
2.1. Safety and liability 2
 
 
 
5. Commissioning 5
5.1. (OFF/ ) selector switch 5
5.2. Adding/Deleting a Sunis Indoor WireFree™ RTS 5
 
5.4. Sunlight simulation 7
5.5. (Mode) button 8
 
6. Use 10
7. Tips and recommendations 12
7.1. Questions about the Sunis Indoor WireFree™ RTS? 12
 
 
CONTENTS

Installation guide
2
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
1. Introduction
The Sunis Indoor WireFree RTS is a wireless solar sensor that
transmits radio signals using Radio Technology Somfy (RTS).
Depending on the detected level of sunlight intensity, the sensor
sends a raise or lower order to the motors or RTS receivers.
This permits automatic control of the sun protection end-products that
protect your interiors (e.g. your furniture, plants, etc.) and to assist
you in saving energy (in summer only).
2. Safety
2.1. Safety and liability
Before installing and using this product, please read this guide
carefully.
This Somfy product must be installed by a professional motorisation
and home automation installer, for whom this guide is intended.
Moreover, the installer must comply with the current standards and
legislation in the country in which the product is being installed, and
inform the customer of the operating and maintenance conditions for
the product.
          
prohibited. Doing so would void the warranty and releases Somfy of
all liability, as does any failure to comply with the instructions given
herein.

product with the associated equipment and accessories.

Installation guide

Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN

To avoid damage to the product:
1) Never immerse it in a liquid!
2) Avoid sharp bumps or blows!

4) Never pierce it!
5) Do no use abrasive products or solvents to clean the product.

1
4
2
5



Installation guide
4
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
3. Contents
1 Sunis indoor WireFree™ RTS
1 Suction cup

a) Protective front cover
b) Sun sensor
c) Battery
d) Rear cover
e) Sunlight detection area
f) Suction cup
g) Potentiometer for setting the sunlight threshold
h) Sun LED
i) (OFF/ ) selector switch
j) Programming button (PROG)
(Mode) button
b gdc ja h if e

Installation guide
5
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
5. Commissioning
 
Slide the (OFF/ ) selector switch to to activate the sunlight
sensor functions.


(PROG) button inactive.
(Mode) button inactive.
Sun LED inactive (No energy
consumption).

(sun LED glows for 5 seconds).
(PROG) button active.
(Mode) button active.
Sun LED active.

The procedure for adding or deleting a
sensor is the same.
To add or delete a Sunis Indoor WireFree™
RTS, use the RTS control point already
programmed to the end-product.
1) Slide the (OFF/ ) selector to .
2) Press on the sides of the front protective
cover and pull to remove it.

Installation guide

Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
Press and hold the (PROG) button on
the already assigned RTS control point
     
forth: the motor or RTS receiver RTS
enters programming mode for 2 minutes.
4)
      
Sunis Indoor WireFree™ RTS. The
     
Sunis Indoor WireFree™ RTS is
programmed.
           
assigned to this sensor.

Clean the surface on which the sensor is to be mounted.

5.3.1. On an inside window sill
1) Screw the suction cup to the bottom of the
sensor (A).
2) Moisten the suction cup.
Position the sensor with the sunlight intensity
detection area (B) towards the exterior and

AB

Installation guide
7
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN

1)         
sensor (C).
2) Moisten the suction cup.
Position the sensor below the area to be
protected by the end-product (D) and press
on the sensor.

If you turn the potentiometer to the (-) position,
the sensor simulates continuous sunlight,
the LED glows green and the end-product is
lowered, stops level with the sensor and is then
raised slightly above the level of the sensor.
Do not leave the sunlight threshold setting at this level.
CD

Installation guide
8
Copyright © 2010 - 2011 Somfy SAS. All rights reserved.
Sunis indoor WireFree™ RTS
EN
5.5. (Mode) button

Press and hold the (Mode) button to activate demonstration mode.
5.5.1. Information mode


If the LED (red/green) is permanently lit: the sensor is in operating mode.
If the LED is red: the level of sunlight intensity is lower than the set
sunlight threshold.
If the LED is green: the level of sunlight intensity is greater than the
set sunlight threshold.

         

Do not change the sunlight threshold setting in demonstration
mode.
The same procedure is used to activate or deactivate
demonstration mode.
- Press and hold (>2 sec.) the (Mode) button to
activate or deactivate demonstration mode.
       
     
is activated. > 2 s