Sonoff SNZB-04 User manual

SNZB-04
User manual V 1.0
Wireless Door/Window Sensor
中文------------------1-6 English- ---- -------- 7-12
Deutsch----------- 13-18 Español------------19-24
Français----------- 25-30 Italiano------------31-36
Русский язык------37-43 Português---------44-50
FCC Warning--------- 51

eWeLink
eWeLink
SONOFF TECHNOLOGIES CO., LTD. English
The device can be operated intelligently via working with the
SONOFF ZigBee Bridge to communicate with other devices.
The device can work wit h other gateways supporting ZigBee 3. 0
wireless protocol. Detailed information is in accordance with the
final product.
Operation instruction
1. Download APP
2. Pull out the battery insulation sheet
>
7

SONOFF TECHNOLOGIES CO., LTD. English
>
3. Add sub-devices
Connect the Bridge before adding the sub-device
Access eWeLink APP, select the Bridge that you want to connect,
and tap “Add” to add a sub-device. Then long press reset button on
the device for 5s until the LED indicator flashes three times, which
means the device has entered the pairing mode, and be patient
until pairing completes.
ZBB rid ge
Add ed: 0
No ch ild de vice, pleas e add.
Add
If the addition failed, move the sub-device closer to the Bridge and try again.
Specifications
Model
Battery model
Wireless connection
Working temperature
Working humidity
Material
Dimension
SNZB-04
ZigBee (IEEE 802.15.4)
-10℃~40℃
10-90%RH (non-condensing)
PC
CR2032(3V)
Transmitter: 47x27x13.5mm
Magnet: 32x15.6x13mm
<10mm
Installation gap
Quiescent current
Emission current
<2uA
<15mA
8

SONOFF TECHNOLOGIES CO., LTD. English
Product Introduction
Features
SNZB-04 is a ZigBee low-energy wireless door/window sensor that
makes you know the opening/closing status of door and window by
separating the magnet from the transmitter. Connect it with the
Bridge and you can create a smart scene to trigger other devices.
Low battery notification
Low-energy Smart scene
LED indicator
Align the mark lines
Transmitter
Magnet
Reset button
9

Conne cting
Kee p the de vic e clo se
eno ugh to t he hub.
25s
Add Devic e
Loo king f or dev ice
3 devices Found
SONOFF ZigBee Bridge supports
connecting multiple sub-devices at the
same time.
Power the Bridge on, access the Bridge page in the eWeLink APP,
and tap “Add”. Then set the sub-device to be paired to the pairing
mode, and be patient until the pairing completes.
>
ZBB rid ge
Add ed: 0
No ch ild de vice, pleas e add.
Add
Delete sub-devices
Long press the reset button on the sub-device for 5s until the LED
indicator flashes three times. In this case, the sub-device is deleted
from the Bridge successfully.
Users can delete sub-devices directly from the sub-device page on APP.
SONOFF TECHNOLOGIES CO., LTD. English
10

Installation methods
SONOFF TECHNOLOGIES CO., LTD. English
1. Tear off the protective film of the 3M adhesive.
2. Try to align the mark line on the magnet with that on the transmitter
during installation.
3. Install them in the opening and closing area separately.
Make sure the installation gap is less than 10mm when the door or the
window is closed.
<10mm
The device weight is less than 1 kg.
The installation height of less than 2 m is recommended.
11

Application
Note:
● Do not install outside the door/window.
● Do not install in the unstable position or in the place exposed to
rain or moisture.
● Do not install near wiring or magnetic object.
Door Window
SONOFF TECHNOLOGIES CO., LTD. English
12

FCC Radiation Exposure Statement:
FCC Warning
Changes or modificat ions not exp ressly ap prov ed by the par ty
responsible for com plia nce could avoid t he user ’s authority t o
operate the equipme nt.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Note:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance20cm between the
radiator & your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
SONOFF TECHNOLOGIES CO., LTD. FCC Warning
51

https://www.sonoff.tech/usermanuals
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the
radio equipment type SNZB-04 is in compliance with Directive
2014/53/EU.The full text of the EU declaration of conformity is
available at the following internet address:
TX Frequency:
ZigBee：2405-2480MHz
MAX PER：
2.21（2405MHz），2.16（2480MHz）
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, shenzhen,
GD, China
ZIP code: 518000 Website: sonoff.tech
MADE IN CHINA