Sony Ericsson HBH-60 User manual

NotforCommercialUse
1
Contents
English.............................................3
Deutsch .........................................17
Español .........................................33
Français.........................................49
Italiano...........................................65
....................................81
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
଼ᄏᒦᆪ

Notfor CommercialUse

Notfor CommercialUse
3
English
Introduction 4
Headset overview 5
Using the headset 9
Troubleshooting 12
Additional information 14
Declaration of conformity 95
Sony Ericsson HBH-60
First edition (July 2002)
This manual is published by Sony Ericsson Mobile
Communications AB, without any warranty. Improvements and
changes to this manual necessitated by typographical errors,
inaccuracies of current information, or improvements to programs
and/or equipment, may be made by Sony Ericsson Mobile
Communications AB at any time and without notice. Such changes
will, however, be incorporated into new editions of this manual.
All rights reserved.
©Sony Ericsson Mobile Communications AB, 2002
Publication number: LZT 108 5897/1 R1A
Some of the services in this manual are not supported by all
networks. This also applies to the GSM International Emergency
Number 112.
Contact your network operator or service provider if you are
in doubt whether you can use a particular service or not.
BLUETOOTH is a trademark of the Bluetooth SIG, Inc. (Special
Interest Group). The Bluetooth trademarks are owned by
Bluetooth SIG, Inc. USA.

Notfor CommercialUse
4 Introduction
Introduction
The Bluetooth™ headset HBH-60
is a portable headset solution
based on Bluetooth wireless
technology.
See “Guidelines for safe and efficient use” on
page 14 and “Limited Warranty” on page 15 before
using your headset.
What is Bluetooth wireless technology?
The Bluetooth wireless technology makes it possible
to connect any compatible portable and stationary
communications device without using cables. The
technology is based on a radio link that offers fast and
reliable transmission of voice and data information.
It does not require a line-of-sight connection in order
to establish communication. Bluetooth wireless
technology uses a globally available frequency range
intended to ensure communication compatibility
worldwide.
How can I use my headset?
You can connect your HBH-60 headset to your mobile
phone or PC – or any device with Bluetooth wireless
technology that supports the Headset profile or the
Handsfree profile. This user’s guide focuses on how
to use the headset with your mobile phone. You need
to have a phone with built-in Bluetooth capability, or
a phone with a Bluetooth adapter connected to it.
When the headset is connected to your mobile phone,
you can use voice control to make calls (if your phone
supports this function). The phone can be tucked away
in your pocket or in a bag. You can handle incoming
and outgoing calls, and adjust the volume, using the
buttons on the headset.

Notfor CommercialUse
Headset overview 5
Headset overview
Front Back
Volume and ring signal down
Volume and ring signal up
Call handling button and
indicator light
Charging
connector
Microphone
Speaker
Ear hook

Notfor CommercialUse
6 Headset overview
Getting started
Before you can use your headset, you must first:
• Charge the headset battery, using an appropriate
Sony Ericsson charger.
• Pair the headset with a device, for example, a mobile
phone.
Compatible Sony Ericsson or Ericsson chargers:
• Travel Charger CTR-10
• Standard Charger CST-13
• Cigarette Lighter Adapter CLA-11
Charging
The headset comes with a built-in rechargeable battery.
We recommend that you charge the battery until the
headset indicator light turns green before using the
headset for the first time. During charging, the
indicator light shows a steady red light if the headset
is turned off, and flashes red if the headset is on.
When the battery is fully charged, the indicator
shows a steady green light if the headset is off,
or a flashing green light if the headset is on.
To charge the battery
1. Connect the charger to the headset and to the mains.
The flash symbol on the charger plug must face
upwards.
2. It takes 1 to 1.5 hours to fully recharge the battery.
3. Tilt the charger plug upwards to remove it when
disconnecting the charger.

Notfor CommercialUse
Headset overview 7
Pairing
To turn the headset on
• Press and hold the call handling button until you
hear a short low tone followed by a short high tone.
The headset indicator light flashes green.
Note: The first time the headset is turned on, it might
automatically be ready for pairing.
To turn the headset off
• Press and hold the call handling button until you
hear a short high tone followed by a short low tone.
The headset indicator light switches off.
Pairing the headset with a phone
You pair the headset with the phone by adding it to
a list of paired devices in the phone. The two devices
then recognize each other when they connect. Once
you have paired your headset with the phone, you do
not need to pair it again until you want to use it with
another device.
To pair the headset with a Sony Ericsson or
Ericsson phone
1. With the headset turned off, press and hold the call
handling button for up to 10 seconds until the
indicator light on the headset flashes green and red.
2. In the phone, scroll to Extras or Connect, YES,
Bluetooth, YES, Paired devices, YES, Add device, YES,
Phone initiates, YES.
3. A list of device types that you can pair with your phone
appears. Scroll to Handsfree or Headset, YES. Make
sure that the headset is within 1 m (3 ft) of the phone.
4. HBH-60 appears in the display. Press YES.
Up to
1 m

Notfor CommercialUse
8 Headset overview
5. Enter the headset passkey (0000), YES.
The phone pairing procedure starts.
6. You may now replace the given headset name with
a personal name tag, YES. When pairing has been
completed, the headset indicator light flashes green.
To pair the headset with another make of phone
1. Prepare your phone according to the phone’s user
documentation on pairing.
2. Press the call handling button for up to 10 seconds
until the indicator light on the headset flashes green
and red. The headset is now ready for pairing.
3. Continue according to the instructions in the phone’s
user documentation. The headset passkey is 0000.
Putting on the headset
1. Make sure the ear hook forms an angle of 90°.
2. Place the ear hook behind your ear.
3. Make sure the microphone is pointing towards your
mouth.
4. Make sure the speaker is positioned as shown in the
picture.
.

Notfor CommercialUse
Using the headset 9
To adjust the ear hook for left-ear use: Using the headset
Once you have paired the headset with your phone,
you can make and receive calls using the headset as
long as it is turned on and within range of the phone
– up to 10 m (30 ft) outdoors or up to 5 m (15 ft)
indoors with no solid objects in between. For best
performance, use the headset and phone in the same
room.
Optimal
performance
Limited
performance
Up to 5 m

Notfor CommercialUse
10 Using the headset
If your phone supports voice dialling and it is
activated, you can use this feature with the headset.
The following instructions cover the use of the
headset with a Sony Ericsson or Ericsson phone with
built-in Bluetooth capability.
Note: Always make sure the Bluetooth operation mode
in the phone is on when using the Bluetooth headset.
Making and answering calls
Phone functionality is still available when the headset
is connected. You can make and answer calls using the
buttons on the headset, or using the keys on the phone,
as usual.
To make a call using voice dialling
1. Make sure the phone and the headset are on and within
range of each other. Press the call handling button.
2. It may take a while to set up the connection between
the phone and the headset. During this time, you might
hear a repeated tone in the headset. After the beep,
voice dial as you normally would.
3. End the call by pressing the call handling button.
To answer a call using the call handling button
1. When the headset rings, press the call handling
button.
Note: If the phone rings first, wait until the headset
rings, then press the call handling button.
2. End the call by pressing the call handling button.
To answer a second call
• You have to use the phone keypad to answer and
handle a second call, but you can still use the headset
for talking and listening. You cannot use the headset
buttons during a second call. Refer to the phone's user
documentation on how to handle more than one call
simultaneously.
To reject a call
• When the headset rings, press and hold the call
handling button until you hear a long beep.
Using voice commands
Voice commands are especially useful when you are
using the headset. Examples of voice commands are
dialling, re-dialling, answering and rejecting calls.