manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Sony
  6. •
  7. Camera Accessories
  8. •
  9. Sony XCD-V60 User manual

Sony XCD-V60 User manual

3287508010
3-287-508-01 (1)
安全のために
ソニー製品は安全に充分に配慮して設計されています。しかし、電気製品は
まちがった使いかたをすると、火災や感電などにより死亡や大けがなど人身
事故につながることがあり、危険です。事故を防ぐために次のことを必ずお
守りください。
安全のための注意事項を守る。
故障したり破損したら使わずに、ソニーのサービス窓口に相談する。


取扱説明書
Operating Instructions
お買い上げいただきありがとうございます。
電気製品は、安全のための注意事項を守らないと、火災や人身
事故になることがあります。
この取扱説明書には、事故を防ぐための重要な注意事項と製品の取り扱いか
たを示してあります。この取扱説明書をよくお読みのうえ、製品を安全にお
使いください。お読みになったあとは、いつでも見られるところに必ず保管
してください。
XCD-V60CR/SX90CR/U100CR
(Color model)
XCD-V60/SX90/U100
(Black and white model)
2007 Sony Corporation Printed in Japan
警告表示の意味
この取扱説明書および製品では、次のよ
うな表示をしています。表示の内容をよ
く理解してから本文をお読みください。
この表示の注意事項を守らないと、
火災
や感電などにより死亡や大けがなど
人身事故につながることがあります。
この表示の注意事項を守らないと、
火災
やその他の事故によりけがをしたり周
辺の物品に損害を与えたりすることが
あります。
注意を促す記号
行為を禁止する記号
行為を指示する記号
下記の注意を守らないと、火災や感電、
落下により死亡や大けがにつながること
があります。
設置は確実に
設置については、必ずお買い上げ店または、巻末に記載
してあるお問い合わせ窓口にご相談ください。
設置は、本機と取り付け金具を含む重量に充分耐えられ
る強度があることをお確かめのうえ確実に取り付けて
ください。充分な強度がないと、落下して、大けがの原
因となります。
また、1 年に一度は、取り付けがゆるんでいないことを
点検してください。
レンズは確実に取り付ける
レンズはネジ部をしっかり締めて取り付けてください。
取り付けかたがゆるいと、レンズがはずれてけがの原因
となることがあります。
また、1年に一度は取り付けがゆるんでいないことを点
検してください。
下記の注意事項を守らないと、
けがをしたり周辺の物品に損害
を与えることがあります。
内部に水や異物を入れない
水や異物が入ると、火災の原因となります。
万一、水や異物が入ったときは、すぐに本機が接続され
ている電源供給機器の電源を切り、DC電源ケーブルや
接続ケーブルを抜いて、ソニーのサービス窓口にご相談
ください。
分解しない、改造しない
分解や改造をすると、火災やけがの原因となります。
点検および修理は、ソニーのサービス窓口にご依頼くだ
さい。
カメラケーブルを傷つけない
カメラケーブルを傷つけると、火災や故障の原因となる
ことがあります。次の項目をお守りください。
設置時に、製品と壁やラック、棚などの間に、はさみ込
まない。
カメラケーブルを加工したり、傷つけたりしない。
重いものをのせたり、引っ張ったりしない。
熱器具に近づけたり、加熱したりしない。
カメラケーブルを抜くときは、必ずプラグを持って抜
く。
芯線の露出や断線などでカメラケーブルが傷んだら、お
買い上げ店に交換をご依頼ください。そのまま使用す
ると、火災の原因となります。





指定された専用機器に接続する
指定された以外の機器を接続すると、火災や故障の原因
となることがあります。
指定された接続ケーブルを使う
この取扱説明書に記されている接続ケーブルを使わな
いと、火災や故障の原因となることがあります。
Owner’s Record
The model and serial numbers are located on the bottom. Record the
serial number in the space provided below. Refer to these numbers
whenever you call upon your Sony dealer regarding this product.
Model No. _____________ Serial No. ______________
WARNING
To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualied personnel only.
IMPORTANT
The nameplate is located on the bottom.
Power Supply
The unit must always be operated with a 12V DC class 2 power supply.
In the USA, use a power supply which is UL Listed.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modications not expressly
approved in this manual could void your authority to operate this
equipment.
All interface cables used to connect peripherals must be shielded in
order to comply with the limits for a digital device pursuant to Subpart
B of Part 15 of FCC Rules.
For customers in Europe
This camera is not intended for use in security applications in the
meaning of the European standard series EN 50132 (Alarm systems -
CCTV surveillance systems for use in security applications).
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan,
Minato-ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony
Deutschland GmbH, Hedelnger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses
given in separate service or guarantee documents.
This apparatus shall not be used in the residential area.

日本語
カメラ設置上のご注意 図A
カメラ設置の際は、周辺機器を含めてカメラに接続されている各機器間で接
地電位の差が生じないようにしてください。接地電位差により故障の原因
となる場合があります。設置の都合により電位差を生ずる場合は、機器の内
いずれかひとつの機器だけを接地するようにしてください。
-1 基本構成/ -2 オプションの構成
IEEE1394b端子 12ピンI/Oコネクター端子
ホスト機器(PCなど)
異常電流
接地電位差 電源(DC-700)
使用上のご注意
電源について
本機の電源は、PCからIEEE1394bケーブルを介して供給されます。電源供
給が不足する場合には、リップルやノイズの少ない安定した電源を供給する
DC-700をご使用ください。
使用・保管場所
次のような場所での使用および保管はお避けください。
極端に暑い所や寒い所。適正使用温度は0〜40℃です。
激しい振動や衝撃のある所。
強力な電波を発生するテレビ、ラジオの送信所の近く。
お手入れ
レンズや光学フィルターの表面に付着したごみやほこりは、ブロアーで払っ
てください。外装の汚れは、乾いた柔らかい布でふきとります。ひどい汚れ
は、中性洗剤溶液を少し含ませた布でふきとった後、からぶきします。アル
コール、ベンジンなどは、変質したり塗料がはげることがありますので、使用
しないでください。
主な特長
XCD-V60CR/SX90CR/U100CRはRAWデータ出力のカラーデジタルカメラ
モジュール、XCD-V60/SX90/U100は白黒デジタルカメラモジュールです。
IEEE1394b端子
転送速度800Mbpsのデジタル出力が可能。IEEE1394b端子を2つ搭載する
ことにより、デイジーチェーン接続が可能です。
高画質
プログレッシブスキャンCCDの採用により、高精細で高速な画像が得られ
ます。
XCD-V60CR/V60は、VGA対応の33万画素CCDにより毎秒90フレームの画
像出力が可能です。XCD-SX90CR/SX90は、SXGA対応の125万画素CCD
により毎秒30フレームの画像出力が可能です。XCD-U100CR/U100は、
UXGA対応の200万画素CCDにより毎秒15フレームの画像出力が可能です。
また、正方画素CCDの採用により、画像処理時にアスペクト比の変換を行う
必要がありません。
外部トリガー機能
外部トリガー信号に同期させて任意のタイミングでシャッターを作動させ
ることができます。
電子シャッター
露光時間は豊富な設定値の中から選択可能。最適な条件で画像を取り込む
ことができます。
12ピンI/Oコネクター端子
IEEE1394b端子からの電源供給が不足する場合、12ピンコネクターから電
源を供給することができます。12ピンコネクターは、トリガー入力、ストロ
ボ出力のほか、汎用のI/Oにも対応しています。
低消費電力
XCD-V60CR/V60/SX90CR/SX90では消費電力を2.8W(DC 12V入力時)、
XCD-U100CR/U100では3.0W(DC 12V入力時)に抑えました。
筐体固定
筐体固定用のネジ穴がCCD基準面の含まれているフロントパネルの下部に
あります。ここでカメラモジュールを固定すれば、光軸のずれを最小限にと
どめることができます。
CCD特有の現象
撮影画面に出る下記の現象は、CCD撮像素子(Charge Coupled Device)
特有の現象で、故障ではありません。
白点
CCD撮像素子は非常に精密な技術で作られていますが、宇宙線などの影響
により、まれに画面上に微小な白点が発生する場合があります。
これはCCD撮像素子の原理に起因するもので故障ではありません。
また、下記の場合、白点が見えやすくなります。
高温の環境で使用するとき
ゲイン(感度)を上げたとき
スローシャッターのとき
スミア現象
強いスポット光やフラッシュ光などを撮影したときに、画面上に縦線や画乱
れが発生することがあります。
モニター画面 縦に尾を引いたような
画像になる。
高輝度の被写体
(強いスポット光、強い反射光、
フラッシュ光、太陽など)
折り返しひずみ
細かい模様、線などを撮影すると、ぎざぎざやちらつきが見えることがあり
ます。
構成 図B
カメラモジュールを中心とした描画システムの構成品目は、次のとおりで
す。基本構成には 〜、オプションの構成には〜を使います。(カ
メラモジュール以外はいずれも別売です。)
カメラモジュール
CCDを用いた、小型、高解像度のカメラです。
IEEE1394bカメラケーブル(市販)
カメラモジュール裏面のIEEE1394b端子に接続し、電力の供給や映像信号の
送出、制御信号の授受を行います。接続不良やカメラ、ケーブルの破損を防
ぐため、固定ねじ付きのケーブルをお使いください。
Cマウントレンズ(市販)
カメラや用途に合ったレンズをお使いください。
カメラ用画像入力ボード(市販)
ホスト機器(PCなど)のPCIバススロットに挿入します。
お使いのシステムに適したIEEE1394対応のボードをご使用ください。
転送速度800Mbpsで使用される場合は、IEEE1394b対応のボードをご使用
ください。
三脚アダプター VCT-ST70I(ソニー製)
三脚を使ってカメラモジュールを固定するとき、このアダプターをカメラモ
ジュールの底部に取り付けます。
カメラアダプター DC-700(ソニー製)
AC電源から電力を供給する場合に、カメラモジュールに接続して使用しま
す。
カメラケーブルCCXC-12P02N(2 m)/05N(5 m)/10N(10 m)
/25N(25 m)(ソニー製)
カメラモジュール裏面の12ピンI/Oコネクター端子に接続し、電力の供給や
トリガー信号の授受を行います。
各部の名称と働き
前面/上面/底面 図C
レンズマウント(Cマウント)
Cマウント式のレンズや光学機器を取り付けます。
ご注意
Cマウント式のレンズとして、レンズマウント面からの飛び出し量が10mm
以下のものを使用してください。
レンズマウント部 10mm以下
カメラ固定用補助穴(上面)
カメラ固定用基準穴(底面)
カメラモジュール固定用に高い精度で切られたネジ穴です。ここでカメラ
モジュールを固定すると、光軸のずれを最小限にとどめることができます。
◆詳細はユーザーズガイドをご覧ください。
の4つのネジ穴は、三脚アダプター取り付け用ネジ穴としても使用でき
ます。三脚を使うときは、この4つのネジ穴を使って三脚アダプター VCT-
ST70Iを取り付けます。
(裏面へ続く)






 
 
English
When Installing the Camera Fig. A
When you install the camera with various peripheral devices and if the devices
have dierent ground electric potential, ground only one device. In case there
is an ground electric potential dierence, the camera may be damaged.
-1 Basic conguration / -2 Optional conguration
IEEE1394b connector 12-pin I/O connector
Host device (e.g., PC) Abnormal electricity
Ground electric potencial dierence 
Power supply unit (DC-700/700CE)
Notes on Operation
Power supply
Power is supplied to the camera module via the IEEE1394b cable connected to a
PC. If the power supply is insucient, use the DC-700/700CE that supplies stable
power with less ripple or noise.
Foreign bodies
Be careful not to spill liquids, or drop any ammable or metal objects in the
camera body.
Locations for operation and storage
Avoid operation or storage in the following places.
Extremely hot or cold locations. Recommended temperature range is 0°C to
40°C (32°F to 104°F)
Locations subject to strong vibration or shock
Near generators of strong electromagnetic radiation such as TV or radio
transmitters
Care
Use a blower to remove dust from the surface of the lens or optical lter. Clean
the exterior with a soft, dry cloth.
If the camera is very grimy, apply a cloth soaked in a mild detergent then wipe
with a dry cloth. Do not apply organic solvents such as alcohol which may
damage the nish.
Overview
The XCD-V60CR/SX90CR/U100CR is a color digital camera module that outputs
RGB Raw Data. The XCD-V60/SX90/U100 is a monochrome digital camera
module.
IEEE1394b connector
The camera module can output a digital image with a transfer speed of
800 Mbps. Two IEEE1394b connectors allow you to make up a daisy chain
connection.
High resolution
The camera module uses a progressive scan CCD and produces high-resolution
and high-speed image output.
The XCD-V60CR/V60 has a CCD of 330,000 pixels (VGA) and outputs a digital
image at 90 frames per second. The XCD-SX90CR/SX90 has a CCD of 1,250,000
pixels (SXGA) and outputs at 30 frames per second. The XCD-U100CR/U100 has
a CCD of 2,000,000 pixels (UXGA) and outputs at 15 frames per second.
Because the CCDs are square pixel CCDs, you don’t need to convert the aspect
ratio in your image processing.
External trigger function
You can operate the shutter at any timing by synchronizing the shutter with the
external trigger signals.
Electronic shutter
You can select the exposure time from a variety of settings. This allows you to
capture an image under optimal conditions.
12-pin I/O connector
When power from the IEEE1394b connector is insucient, power is supplied
through the 12-pin connector. The 12-pin connector is also used for a trigger
input and strobe output, and as a general-purpose I/O port.
Low power consumption
The power consumption is decreased to 2.8 W for the XCD-V60CR/V60/SX90CR/
SX90 or 3.0 W for the XCD-U100CR/U100, with 12 V DC input.
Body xing
The mounting screw holes are provided in the reference plane on the lower
surface of the body, allowing mounting with the absolute minimum deviation
of the optical axis.
Phenomena Specic to CCD Image Sensors
The following phenomena that may appear in images are specic to CCD (Charge
Coupled Device) image sensors. They do not indicate malfunctions.
White ecks
Although the CCD image sensors are produced with high-precision
technologies, ne white ecks may be generated on the screen in rare cases,
caused by cosmic rays, etc.
This is related to the principle of CCD image sensors and is not a malfunction.
The white ecks especially tend to be seen in the following cases:
when operating at a high environmental temperature
when you have raised the gain (sensitivity)
when using the slow shutter
Vertical smear
When an extremely bright object, such as a strong spotlight or ashlight, is
being shot, vertical tails may be produced on the screen, or the image may be
distorted.
Monitor screen Vertical tails shown
on the image
Bright object
(e.g. strong spotlight,
strong reected light,
ashlight, the sun)
Aliasing
When ne patterns, stripes, or lines are shot, they may appear jagged or icker.
System Components Fig. B
The camera module imaging system comprises the following products.
Products to are used for the basic conguration, and to for the
optional conguration. (All the products except the camera module are
available separately.)
Camera module
This is a small-size, high-resolution, camera module using a CCD image sensor.
IEEE1394b camera cable (commercially available)
Connect this cable to the IEEE1394b connector on the rear panel of the camera
module. The power and image/control signals are transmitted through this
cable. To prevent a poor connection or damage to the camera or cable, use the
cable equipped with xing screws.
C-mount lens (commercially available)
Use an appropriate lens for the camera module and usage.
Camera module interface board (commercially available)
Install the board in a PCI bus slot of a host device such as a PC.
Select an IEEE1394 interface board to match your system.
Select an IEEE1394b interface board if you use the transfer speed of 800 Mbps.
VCT-ST70I tripod adaptor (Sony)
Attach this adaptor to the bottom of the camera module to x the camera
module to a tripod.
DC-700/700CE camera adaptor (Sony)
Connect this adaptor to the camera module to enable power supply from an
ordinary AC power source.
CCXC-12P02N (2 m, 6.6 ft)/05N (5 m, 16.4 ft)/10N (10 m, 32.8 ft)/
25N (25 m, 82 ft) camera cable (Sony)
Connect this cable to the 12-pin I/O connector on the rear panel of the camera
module. The cable is used for power supply and exchange of trigger signals.
Location and Function of Parts and Operation
Front/Top/Bottom Fig. C
Lens mount (C-mount)
Attach any C-mount lens or other optical equipment.
Note
The lens must not project more than 10 mm (13/32 inch) from the lens mount.
Lens mount face 10 mm (13/32 inch) or less
Auxiliary holes (top)
Reference holes (bottom)
These precision screw holes are for locking the camera module. Locking the
camera module into these holes secures the optical axis alignment.
For details, refer to the Technical Manual.
Four screw reference holes can be used as the tripod adapor screw holes,
too. Screw the VCT-ST70I tripod adaptor into the four screw holes when you use
a tripod.
(continued on the reverse side)






Digital Camera Module





カメラ/ Camera



–1
–2
カメラ/ Camera
English
Rear Fig. D
IEEE1394b connectors
Connect an IEEE1394b camera cable (not supplied) to this connector.
Pin No. Signal Pin No. Signal
1 TPB– 6 VG
2 TPB+ 7 NC
3 TPA– 8 VP
4 TPA+ 9 TPBG
5 TPAG
12-pin I/O connector
When power from the IEEE1394b connector is insucient, power is supplied
through this connector.
Connect a camera cable such as the CCXC-12P05N to this connector.
Pin No. Signal Pin No. Signal
1 Power GND 7 GPIO IN 2
2 Power IN 8 GPIO OUT 2-
3 ISO GND 9 GPIO OUT 2+
4 Strobe OUT 10 GPIO IN 1
5 GPIO OUT 1- 11 Trigger IN
6 GPIO OUT 1+ 12 ISO GND
Installation
Fitting the lens Fig. E
1Remove the lens mount cap.
2Screw in the lens (not supplied), and turn it until it is secured.
Note
Clean the optical lter with a commercially available blower brush to remove
dust.
Using a tripod Fig. F
To use the tripod, install the VCT-ST70I tripod adaptor (not supplied) on the
camera module.
Use a tripod screw with a protrusion () extending
from the installation surface, as follows:
ISO standard: Length 4.5 mm to 5.0 mm
ASA standard: Length 0.197 inches
Tighten the tripod screws using a hand screwdriver.
Note
When you install the tripod adaptor, use the screws supplied with the tripod
adaptor.
Connecting the camera cable Fig. G
Connect a commercially available IEEE1394b camera cable to the IEEE1394b
connector and the 1394b interface connector of your PC. When you connect
the cable, insert the cable connector into the IEEE1394b connector until it snaps
into place, holding it. Then, tighten the xing screws placed on both sides of the
cable connector.
IEEE1394b connector
Fixing screws
IEEE1394b camera cable (not supplied)
Note
Loose xing screws may cause a poor connection or damage to the camera or
cable. Be sure to tighten the xing screws.
When power supply from the IEEE1394b
connector is insucient Fig. H
Power can be supplied to the camera module via the DC-700/700CE camera
adaptor (optional) and a camera cable such as CCXC-12P05N (optional) if power
supply from the IEEE1394b connector is insucient.
12-pin I/O connector
Camera cable (e.g. CCXC-12P05N)
to AC power source
CAMERA connector
AC IN connector
Trigger generator
Controlling the Camera from Your PC
You can control the camera from your PC. The following table shows the control
functions.
Functions common to all models
Control function Description
Gain Color model 0 to +18 dB
Black and white
model 0 to +24 dB
Shutter Setting the shutter speed between 1/100,000 and 16 sec.
Brightness Pedestal level adjustable
Gamma Customizing the gamma curve using 1,024 gamma tables
(10 bits) (IIDC extended function)
Trigger Mode 0 (control by register) and Mode 1 (control by pulse
width) supported for hardware trigger/software trigger
Broadcast commands supported for software trigger
Strobe Out Setting the delay from the exposure start and the pulse
width by register value
AutoExposure Keeping a constant average image level by the image
level detection and feedback to gain and shutter
AutoExposure
Detection Frame
Setting
Setting the detection area for Auto Exposure
GPIO Assigning GPIO (General-Purpose Input/Output) to the
12-pin connector
MemoryShot Saving an image to the built-in frame memory and
reading the saved image from the memory
ISO Enable (Video
Start) Starts transmitting an image in continuous mode
OneShot/
MultiShot
OneShot Transmitting an image
MultiShot Transmitting the specied number of
images
DataDepth Indicating the eective bit length in 16-bit mode
CameraInitialize Resetting the camera to the default features
MemoryChannel PresetMemory0 (factory default status) and 1 user
available memory channel / 15 user available memory
channels selectable
1394 Bus
Synchronization
Dening the exposure timing in synchronization with
the cycle time register of 1394 bus
TriggerDelay Specifying the delay time after which the received
trigger becomes eective
PartialScan Partition by a unit of 32 lines x 24 pixels available
UserFreeMemory A 256-byte user available memory provided
Bulk Mode Acquiring images continuously by changing the settings
in memory channels
日本語
後面 図D
IEEE1394b端子
市販のIEEE1394bカメラケーブルを接続します。
ピン番号 信号 ピン番号 信号
1 TPB−6 VG
2 TPB+7 NC
3 TPA−8 VP
4 TPA+9 TPBG
5 TPAG
12ピンI/Oコネクター端子
IEEE1394b端子からの電源供給が不足する場合、この端子から電源を供給す
ることができます。
カメラケーブルCCXC-12P05Nなどが接続できます。
ピン番号 信号 ピン番号 信号
1電源 (アース) 7 GPIO入力2
2電源入力 8 GPIO出力2−
3 ISO(アース) 9 GPIO出力2+
4ストロボ出力 10 GPIO入力1
5 GPIO出力1−11 トリガー入力
6 GPIO出力1+12 ISO(アース)
設置
レンズの取り付け 図E
1レンズマウントキャップをはずす。
2レンズ(別売)を回して取り付ける。
ご注意
光学フィルターの表面に付着したごみやほこりは、市販のブロアーで払って
ください。
三脚の取り付け 図F
三脚アダプター VCT-ST70I(別売)をカメラモジュールに取り付けてから三
脚に取り付けます。
三脚の取付部のネジは取付面からの飛び出し量()が下記のものを使用して
ください。
ISO規格 :4.5mm 〜5.0mm
ASA規格 :0.197インチ
ネジはハンドトライバーで締めつけてください。
ご注意
三脚アダプター(別売)を取り付けるときは、三脚アダプターに付属のネジ
を使用してください。
カメラケーブルの接続 図G
市販のIEEE1394bカメラケーブルでIEEE1394b端子とパソコンの1394bイ
ンターフェース端子を接続してください。接続する際は、ケーブルのコネク
ター部を持ち、固定するまでしっかりと差し込んでください。
その後、両側にある固定ねじを締め付けてください。
IEEE1394b端子
固定ねじ
IEEE1394bカメラケーブル(市販)
ご注意
固定ねじがゆるむと、接続不良やカメラ、ケーブルの破損の原因となります。
固定ねじはしっかり締め付けてください。
IEEE1394b端子からの電源供給が不足する場合
図H
IEEE1394b端子からの電源供給が不足する場合、カメラアダプター DC-
700(別売)とカメラケーブルCCXC-12P05N(別売)などを介して電源を供
給することもできます。
12ピンI/Oコネクター端子
カメラケーブル(CCXC-12P05Nなど)
AC電源へ
CAMERA端子
〜AC IN端子
トリガー発生器
パーソナルコンピューターによるコントロール
本機はパーソナルコンピューターによりコントロールします。コントロー
ルできる機能は以下の表のとおりです。
全モデル共通機能
制御項目 内容
ゲイン カラーモデル 0 〜+18 dB
白黒モデル 0 〜+24 dB
シャッター 1/100,000 〜16秒に可変
ブライトネス ペデスタルレベルの可変
ガンマ 1024個のガンマテーブル(10ビット)により、ガン
マカーブの自由設定が可能(IIDC拡張機能)
トリガー ハードウェアトリガー /ソフトウェアトリガーの
Mode0(レジスター制御)、Mode1(信号幅制御)
をサポート
ソフトウェアトリガーはブロードキャストコマン
ドにも対応
ストロボ出力 レジスターにより、露光開始からのディレイと信
号幅を制御
オートエクスポージャー 映像のレベルを検波して、ゲイン、シャッターに
フィードバックをかけることにより、映像の平均
レベルを一定化
オートエクスポージャー
検波枠設定 オートエクスポージャーの検波エリアの設定
GPIO 12ピンコネクターに割り当てるGPIOの制御
メモリーショット 内蔵フレームメモリーに映像を保存し、あとで映
像の読み出しを行う
ISO Enable(ビデオス
タート)連続モードで画像を転送開始
OneShot/MultiShot OneShot 画像1枚を転送
MultiShot 指定した枚数の画像を転送
DataDepth 16ビットモード時に有効なビット長を示す
CameraInitialize フィーチャーを初期値にリセット
メモリーチャンネル PresetMemory0(工場出荷状態)および
ユーザー設定チャンネル1 ch/15 ch切り換え可
能
1394バス同期 1394バスのサイクルタイムレジスターに同期して
露光のタイミングを決定
トリガーディレイ トリガー受信時、指定した時間後にトリガーを有
効にする
パーシャルスキャン 32ライン x 24ピクセルのユニットに分割可能
ユーザーフリーメモリー 256バイトのユーザー使用可能なメモリーを装
備
バルクモード メモリーチャンネルを使用して設定を変えなが
ら、連続して画像を取得
XCD-V60CR/SX90CR/U100CR(カラーモデル)のみ
制御項目 内容
ホワイトバランス(Raw
モード)
R、Bレベルの調整
オートホワイトバランス/ワンプッシュホワイトバ
ランス
Gゲイン Gゲインの調整
オプティカルフィルター ベイヤーパターンの切り換え
XCD-V60/SX90/U100(白黒モデル)のみ
制御項目 内容
3 x 3フィルター 3 x 3フィルターの切り換え
シャープネス 映像の輪郭の強弱を調整
◆これらの項目は、IEEE1394規格のデジタルカメラプロトコルVer.1.31に準拠
しています。詳細はユーザーズガイドをご覧ください。
主な仕様
撮像素子 プログレッシブスキャンIT CCD
XCD-V60CR/V60/SX90CR/SX90: 1/3型
XCD-U100CR/U100: 1/1.8型
インターフェース仕様
IEEE1394b – 2002
出力信号フォーマット(水平/垂直)
XCD-V60CR/V60: 640 x 480 (VGA)
XCD-SX90CR/SX90: 1,280 x 960 (SXGA)
XCD-U100CR/U100: 1,600 x 1,200 (UXGA)
フレームレート XCD-V60CR/V60: 90 fps
XCD-SX90CR/SX90: 30 fps
XCD-U100CR/U100: 15 fps
転送速度 800/400 Mbps
外部トリガー信号(条件)
パルス幅:10 μs以上
極性:負
振幅:DC 5 〜24V
レンズマウント Cマウント
フランジバック 17.526 mm
最低被写体照度 XCD-V60CR/SX90CR/U100CR: 20 lx (F1.4 Gain:
+18 dB)
XCD-V60/SX90/U100: 2 lx (F1.4 Gain: +24 dB)
ガンマ γ= 1(LUTで設定可)
ゲイン XCD-V60CR/SX90CR/U100CR: 0 〜+18 dB、オー
トゲイン
XCD-V60/SX90/U100: 0 〜+24 dB、オートゲイ
ン
シャッター速度 1/100,000 〜16秒、オートシャッター
電源 IEEE1394bカメラケーブルまたは12ピンコネク
ター付きカメラケーブルより、DC +8 V 〜+30 V
を供給
消費電力 XCD-V60CR/V60/SX90CR/SX90: 2.8 W(DC 12V
入力時)
XCD-U100CR/U100: 3.0 W(DC 12V入力時)
性能保証温度 0 〜+40℃
動作温度 −5〜+45℃
保存温度 −30〜+60℃
使用湿度 20〜80%(結露のない状態で)
保存湿度 20〜95%(結露のない状態で)
耐振動性 10G (20Hz〜200Hz、固定用基準穴使用時)
耐衝撃性 70G
外形寸法 44 (W)×33 (H)×57.5 (D)mm、突起部含まず
重量 140g
付属品 レンズマウントキャップ (1)
取扱説明書 (1)
仕様および外観は改良のため予告なく変更することがありますが、ご了承く
ださい。
XCD-V60CR/SX90CR/U100CR (color models) only
Control function Description
WhiteBalance (Raw
mode)
Adjusting the R and B levels individually
Auto white balance, One Push white balance available
G Gain Adjusting the G gain
OpticalFilter Switching the Bayer pattern
XCD-V60/SX90/U100 (black and white models) only
Control function Description
3 x 3 Filter Switching the 3 x 3 lter
Sharpness Adjusting the image contour strength
These control items comply with Digital Camera Protocol, Ver. 1.31, of the IEEE1394 Standard.
For more details, refer to the Technical Manual.
Specications
Pickup device Progressive scan IT CCD
XCD-V60CR/V60/SX90CR/SX90: 1/3 type
XCD-U100CR/U100: 1/1.8 type
Interface IEEE1394b – 2002
Output signal format (horizontal/vertical)
XCD-V60CR/V60: 640 x 480 (VGA)
XCD-SX90CR/SX90: 1,280 x 960 (SXGA)
XCD-U100CR/U100: 1,600 x 1,200 (UXGA)
Frame rate XCD-V60CR/V60: 90 fps
XCD-SX90CR/SX90: 30 fps
XCD-U100CR/U100: 15 fps
Transfer speed 800/400 Mbps
External trigger signal (conditions)
Pulse width: 10 μs or more
Polarity: Negative
Amplitude: 5 to 24 V DC
Lens mount C-mount
Flange back 17.526 mm
Minimum illumination XCD-V60CR/SX90CR/U100CR: 20 lx (F1.4, Gain: +18
dB)
XCD-V60/SX90/U100: 2 lx (F1.4, Gain: +24 dB)
Gamma γ= 1 (selectable by LUT)
Gain XCD-V60CR/SX90CR/U100CR: 0 to +18 dB, Auto
gain
XCD-V60/SX90/U100: 0 to +24 dB, Auto gain
Shutter speed 1/100,000~16 seconds, Auto shutter
Power +8 V to +30 V DC from IEEE1394b camera cable or
camera cable with 12-pin connector
Power consumption XCD-V60CR/V60/SX90CR/SX90: 2.8 W (12 V DC
input)
XCD-U100CR/U100: 3.0 W (12 V DC input)
Performance guaranty temperature
0 to +40°C (32 to 104°F)
Operating temperature –5 to +45°C (23 to 113°F)
Storage temperature –30 to +60°C (–22 to 140°F)
Operating relative humidity
20 to 80% (no condensation)
Storage relative humidity 20 to 95% (no condensation)
Vibration resistance 10 G (20 Hz to 200 Hz, at using the reference holes)
Shock resistance 70 G
External dimension (w/h/d) 44 × 33 × 57.5 mm (13/4× 13/16 × 23/8inches), not
including projecting parts
Mass 140 g (4 oz)
Accessories Lens mount cap (1)
Operating Instructions (1)
Design and specications are subject to change without notice.
IMPORTANT
The nameplate is located on the bottom.
Note
Always verify that the unit is operating properly before use. SONY WILL
NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY,
OR FOR ANY OTHER REASON WHATSOEVER.
Regular parts replacement
Some of the parts that make up this product (electrolytic condenser, for
example) need replacing regularly depending on their life expectancies.
The lives of parts dier according to the environment or condition in which
this product is used and the length of time it is used, so we recommend
regular checks.
Consult the dealer from whom you bought it for details.
ユーザーズガイドについて
この取扱説明書は本機の基本的な機能と使用方法について記載しており
ます。
より詳しい情報をお知りになりたい方は「ユーザーズガイド」をご覧くだ
さい。
「ユーザーズガイド」については営業担当者にお問い合わせください。
About the Technical Manual
The Operating Instructions describe the functions and use of this product.
For more details, see the Technical Manual. Please ask your sales
representative about the Technical Manual.
重要
機器の名称と電気定格は、底面に表示されています。
お使いになる前に、必ず動作確認を行ってください。故障その他に伴う
営業上の機会損失等は保証期間中および保証期間経過後にかかわらず、
補償はいたしかねますのでご了承ください。
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準に基
づくクラスA情報技術装置です。この装置を家庭環境で使用すると電波
妨害を引き起こすことがあります。この場合には使用者が適切な対策を
講ずるよう要求されることがあります。
定期交換部品について
本機で使用されている部品の中には有寿命部品として定期交換が必要な
もの(電解コンデンサーなど)があります。
使用環境や条件により部品の寿命は異なりますので、長期間ご使用され
る場合は定期点検をお勧めします。
◆詳しくはお買い上げ店にお問い合わせください。






Other manuals for XCD-V60

1

This manual suits for next models

5

Other Sony Camera Accessories manuals

Sony XCD-SX910/X710 User manual

Sony

Sony XCD-SX910/X710 User manual

Sony MPK-THJ User manual

Sony

Sony MPK-THJ User manual

Sony GPS-CS1KASP - GPS Unit For Digital Cameras User manual

Sony

Sony GPS-CS1KASP - GPS Unit For Digital Cameras User manual

Sony CSS-HD1 Manual de instrucciones / Manual de... User manual

Sony

Sony CSS-HD1 Manual de instrucciones / Manual de... User manual

Sony VF 37PK/S User manual

Sony

Sony VF 37PK/S User manual

Sony BKP-7090 User manual

Sony

Sony BKP-7090 User manual

Sony VCT-D480RM User manual

Sony

Sony VCT-D480RM User manual

Sony SELP1 8105G User manual

Sony

Sony SELP1 8105G User manual

Sony VCT-EXC1 User manual

Sony

Sony VCT-EXC1 User manual

Sony CA-D50 User manual

Sony

Sony CA-D50 User manual

Sony VG-B30AM User manual

Sony

Sony VG-B30AM User manual

Sony MPK-P9 User manual

Sony

Sony MPK-P9 User manual

Sony RM-VD1 User manual

Sony

Sony RM-VD1 User manual

Sony MPK-THA User manual

Sony

Sony MPK-THA User manual

Sony BRS-200 User manual

Sony

Sony BRS-200 User manual

Sony BRCSDP12 User manual

Sony

Sony BRCSDP12 User manual

Sony CCU-D50P User manual

Sony

Sony CCU-D50P User manual

Sony BVF-20W User manual

Sony

Sony BVF-20W User manual

Sony VCT-2200RM User manual

Sony

Sony VCT-2200RM User manual

Sony SPK-DVF5 User manual

Sony

Sony SPK-DVF5 User manual

Sony MPK-THHB User manual

Sony

Sony MPK-THHB User manual

Sony VCL-2030 S User manual

Sony

Sony VCL-2030 S User manual

Sony NC-AA-HJ User manual

Sony

Sony NC-AA-HJ User manual

Sony LCM-D700 User manual

Sony

Sony LCM-D700 User manual

Popular Camera Accessories manuals by other brands

Panasonic DMW-HGR2 user manual

Panasonic

Panasonic DMW-HGR2 user manual

Duracell Zinc Air Battery 146E Specification sheet

Duracell

Duracell Zinc Air Battery 146E Specification sheet

Axis P33-V Series installation guide

Axis

Axis P33-V Series installation guide

ePropulsion E Series user manual

ePropulsion

ePropulsion E Series user manual

F&V HDV-Z96 user guide

F&V

F&V HDV-Z96 user guide

RRS TA-3-QC quick start guide

RRS

RRS TA-3-QC quick start guide

Miller Compass XV2 Fluid Head Operator's manual

Miller

Miller Compass XV2 Fluid Head Operator's manual

AMPHIBICO HD Wave WAVH0760 operating manual

AMPHIBICO

AMPHIBICO HD Wave WAVH0760 operating manual

RODE Microphones VideoMic Me-C quick start guide

RODE Microphones

RODE Microphones VideoMic Me-C quick start guide

Manfrotto 160 instructions

Manfrotto

Manfrotto 160 instructions

Stahl 8316 Series operating instructions

Stahl

Stahl 8316 Series operating instructions

PROAIM P-GHF-01 Assembly manual

PROAIM

PROAIM P-GHF-01 Assembly manual

Manfrotto 554 instructions

Manfrotto

Manfrotto 554 instructions

Aigis Mechtronics MT9213 Installation and operating instructions

Aigis Mechtronics

Aigis Mechtronics MT9213 Installation and operating instructions

SIRUI 135mm T2.9 1.8x Full-Frame Anamorphic Lens instructions

SIRUI

SIRUI 135mm T2.9 1.8x Full-Frame Anamorphic Lens instructions

ARRI MAXIMA user manual

ARRI

ARRI MAXIMA user manual

ecofort ecoQ instructions

ecofort

ecofort ecoQ instructions

KERN SFB-A01 Assembly instructions

KERN

KERN SFB-A01 Assembly instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.