Sony PlayStation DualSense Edge User manual

CFI-ZCP1
Wireless Controller / Manette de jeu sans fil
Instruction Manual / Mode d’emploi
DualSense Edge™
1000035768

2
Health and Safety
–Areas near fire alarms, automatic doors and other
types of automated equipment.
MAGNETS AND MEDICAL DEVICES
This product has magnets which may interfere with
pacemakers, defibrillators and programmable shunt valves
or other medical devices. Do not place this product close
to such medical devices or persons who use such medical
devices. Consult your doctor before using this product if
you use such medical devices.
VOLUME LEVEL
Permanent hearing loss may occur if the headset or
headphones are used at high volume. Set the volume to a
safe level. Over time, increasingly loud audio may start to
sound normal but can actually be damaging your hearing.
If you experience ringing or any discomfort in your ears or
mued speech, stop listening and have your hearing
checked. The louder the volume, the sooner your hearing
could be aected. To protect your hearing:
–Limit the amount of time you use the headset or
headphones at high volume.
–Avoid raising the volume to block out noisy
surroundings.
–Lower the volume if you can’t hear people speaking
near you.
Before using the product, carefully read this manual and
any manuals for compatible hardware. Retain instructions
for future use. Parents or guardians of children should
read this manual for safe use.
This product has been designed with the highest concern
for safety. However, any electrical device, if used
improperly, has the potential for causing fire, electrical
shock or personal injury. Observe all warnings, precautions
and instructions.
Stop use and disconnect cables immediately if the product
functions in an abnormal manner, produces unusual
sounds or smells or becomes too hot to touch.
WARNING
RADIO WAVES
Radio waves may aect electronic equipment or medical
devices (for example, pacemakers), which may cause
malfunctions and possible injuries.
• If you use a pacemaker or other medical device, consult
your doctor or the manufacturer of your medical device
before using the wireless networking feature (Bluetooth®
and wireless LAN).
• Do not use the wireless networking feature in the
following locations:
–Areas where wireless network use is prohibited, such
as in hospitals. Abide by medical institution
regulations when using the console on their premises.
EN

3
Health and Safety
LITHIUM-ION BATTERY
The controller contains a lithium-ion rechargeable battery.
Do not handle damaged or leaking lithium-ion batteries. If
the built-in battery fluid leaks, stop using the product
immediately and contact the appropriate PlayStation
customer service helpline which can be found within the
accompanying documentation. If the material gets into
the eyes, do not rub. Immediately flush the eyes with
clean water and seek medical attention. If the material
comes into contact with the skin or clothes, immediately
rinse the aected area with clean water and consult your
doctor. Do not allow the battery to come into contact with
fire or subject it to extreme temperatures such as in direct
sunlight, in a vehicle exposed to the sun or near a heat
source. Never attempt to open, crush, heat or set fire to
the controller or the battery. Do not leave the battery
charging for a prolonged period of time when the
controller is not in use.
YOUNG CHILDREN INJURIES
CHOKING HAZARD – Small parts. Keep the product out of
the reach of young children. Young children may swallow
small parts, may wrap the cables around themselves,
which may inflict injury or cause an accident or a
malfunction.
NEVER DISASSEMBLE OR MODIFY THE PRODUCT
OR ACCESSORIES UNLESS AUTHORIZED IN THIS
MANUAL
There is a risk of fire, electric shock or injury.
Precautions
Taking breaks
• Avoid prolonged continuous use of this product.
Generally we recommend that you take 15 minute
breaks for every hour of play.
• Avoid playing when you are tired or need sleep.
• Stop using the product immediately if you begin to feel
tired or if you experience discomfort or pain in your
hands or arms while operating the controller. If the
condition persists, consult a doctor.
• If you experience any of the following health problems,
discontinue use of the product immediately. If
symptoms persist, consult a doctor.
–Dizziness, nausea, fatigue or symptoms similar to
motion sickness
–Discomfort or pain in a part of the body, such as eyes,
ears, hands or arms
Vibration function
• If the controller is sitting on a flat surface, the vibration of
the controller during gameplay may cause it to fall,
leading to injury or malfunction.
EN

4
Health and Safety
• Do not use the vibration or trigger eect function if you
have any ailment or injury to the bones, joints or
muscles of your hands or arms. If you have an ailment or
an injury, do not play titles with these features using the
controller unless you have set those functions to “O”.
To enable or disable the features, select Settings >
Accessories from the home screen of the PlayStation®5
console.
Static shock
When using the headset or headphones in particularly dry
air conditions, you may sometimes experience a small and
quick (static) shock on your ears. This is a result of static
electricity accumulated in the body, and is not a
malfunction of your headset or headphones. This eect
could be reduced by wearing clothes made from materials
that do not easily generate static shock.
Motion sensor
When using the motion sensor function of the controller
be cautious of the following points. If the controller hits a
person or object, it may cause accidental injury or
damage.
• Before using the motion sensor function, make sure you
have enough space to move around.
• Firmly grip the controller to prevent it from slipping out
of your grasp and causing damage or injury.
• If using a controller that is connected to the PS5 console
with a USB cable, make sure there is enough space for
the cable so that the cable will not hit a person or object.
Light bar
Do not stare at the light bar on the controller when it is
blinking. Stop using the controller immediately if you
experience any discomfort or pain.
Liquid, dust, smoke, steam and heat
• Always ensure the product and its connectors are free of
liquid, excess dust and small particles.
• Do not leave the product in the following areas during
use, storage or transportation.
–Areas exposed to smoke or steam
–Areas with high humidity, dust or cigarette smoke
–Areas near heating appliances, areas exposed to
direct sunlight or areas that retain heat
Set up and handling
• Do not use the cables if they are damaged or modified.
• Do not place heavy items on the product or cables,
throw or drop the product, or otherwise expose it to
strong physical impact.
• Do not place the product on surfaces that are unstable,
tilted or subject to vibration.
• Do not leave the product on the floor.
• Do not walk on the cables or pinch them, particularly
near to the connectors.
• Do not pull or bend the cables with excessive force.

5
• Do not place the console and connected accessories on
the floor or in a place where they may cause someone
to trip or stumble.
• Do not touch the connectors or insert any foreign
objects into them or the product.
• Unplug the cables if you want to clean or move the
product or do not intend to use it for an extended period
of time.
• Do not touch the product during an electrical storm.
• Do not expose the product, accessories or battery to
high temperatures, high humidity, or direct sunlight
during operation, transportation, and storage.
Contents
Health and Safety ............................................ 2
DualSense Edge Wireless Controller features .... 6
Product contents ............................................. 8
Part names ...................................................... 9
Pair the controller ........................................... 12
Customize the controller ................................. 12
Use the controller with a wired connection....... 17
Charge the controller ...................................... 17
Use and handling ........................................... 18
Compliance information ................................. 19
Specifications ................................................ 20
LIMITED WARRANTY........................................ 21
Further information ........................................ 22
EN

6
DualSense Edge Wireless Controller features
Front
Front cover
Connector housing
Lock the connector housing to your controller to stop the
USB cable from detaching ( page 17).
Stick cap
Use the standard caps or switch them out for one of the
two other cap types included ( page 12).
Fn button
While holding down the Fn button, use your assigned
buttons to switch between profiles ( page 16), access
settings and adjust volume and audio balance.
Stick module
Replace the stick modules if needed ( page 14).
Additional modules sold separately.

7
DualSense Edge Wireless Controller features
L2/R2 stop sliders
Adjust the stroke of the L2/R2 buttons ( page 16).
Back button
Choose from the two back button types included to best
suit your playstyle. Attach the back buttons ( page 13)
and customize their functions.
Rear
EN

8
Product contents
Controller USB braided cable Carrying case Connector housing
Stick cap
Standard caps
(attached to controller)
Low dome caps
High dome caps
Back button
Half dome back buttons Lever back buttons
Instruction manual (this manual)

9
Part names
H Right stick/R3 button*
I Fn button
Use in combination with other buttons.
• Fn button + action buttons: switch between profiles
• Fn button + (options) button: customize a profile
• Fn button + up/down button: adjust volume of
headphones
• Fn button + left/right button: adjust audio balance
J Speaker
K (PS) button
L Headset jack
M Microphone
N (mute) button
O Left stick/L3 button*
* The stick caps are changeable ( page 12).
A B C D E C F G
H
O I N M L K J I
Front
A Directional buttons
B (create) button
C Light bar
D Touch pad/touch pad button
E Player indicator
F (options) button
G Action buttons
button button button button
EN

10
Part names
Top Rear
A B C D E
A B
EF D C
A R1 button
B R2 button
C USB port
D L1 button
E L2 button
A R2 stop slider
B L2 stop slider
C Left back button slot*1
D Reset button*2
E RELEASE latch
F Right back button slot*1
*1The back buttons are changeable ( page 13).
*2If your controller is responding unexpectedly, try resetting your
controller. Use a pin or similar tool (not included) to press the
reset button. This will not reconfigure the controller or aect
pairing and profile settings.

11
Part names
Carrying case
You can store an additional stick
module (sold separately) here.
EN

12
Customize the controllerPair the controller
The first time you use the controller, you’ll need to pair it
with your PS5™ console.
1 Turn on your console.
2 Connect the controller to your console using
the included USB cable.
3 Press the (PS) button.
The controller powers on. After the light bar blinks, the
player indicator lights up.
When your controller has enough battery life, you can
disconnect the USB cable and use your controller
wirelessly.
Change the stick cap
Switch out the stick caps with one of the dierent types
included and find which best suits your playstyle.
Remove the caps
Pull the cap directly away from the controller.
Attach the caps
Press the cap down onto the stick until you hear a “click”.

13
Customize the controller
Attach or remove the back button
The back buttons are changeable. Choose from the
dierent back button types included to best suit your
playstyle.
For more details on assigning functions to the back
buttons, refer to the PS5 User’s Guide ( page 22).
Attach the half dome back button
Insert the half dome back button into a back button slot.
The half dome back button is interchangeable.
Attach the lever back button
Insert the lever back button into the corresponding back
button slot. The right and left lever back buttons are not
interchangeable. Check which button is right (RB) and left
(LB) before attaching them.
Remove the back button
Pull the back button inwards and towards the top of the
controller. Then, in that position, lift it up from the slot.
EN

14
Customize the controller
Replace the stick module
If a stick doesn’t work properly or stops working, you can
replace it with a new stick module for DualSense Edge
Wireless Controller (sold separately). Left and right stick
modules are interchangeable and can be attached to
either side.
Caution
• Replace the stick module out of the reach of young
children, as there is a danger of it being mistakenly
swallowed.
• Take care not to catch your hands in the stick
module’s lever or gaps in the controller, as this may
cause injury.
• When turning the controller on, make sure the front
cover is securely attached.
Notices
• Before attaching or removing the stick module, touch
a nearby metal-grounded object to remove any static
electricity from your body. Failure to do so may cause
the stick module or controller to malfunction.
• Do not touch the connectors on the stick module or
inside the controller.
1 Make sure the player indicator on the
controller is o.
If the player indicator is on, press and hold the (PS)
button until it turns o.
2 Disconnect the USB cable from the controller.
3 Remove the front cover.
Slide the RELEASE latch on the back of your controller
to remove the cover.
RELEASE latch

15
Customize the controller
4 Raise the release lever.
5 Remove the stick module, and attach a new
stick module.
Make sure that the stick module is positioned
correctly, and then slide the module along the
grooves of the controller.
To remove To attach
6 Lower the release lever.
7 Attach the front cover.
Align the raised parts of the cover with the notches on
the controller, and then carefully push the cover into
place.
Raised parts
EN

16
Customize the controller
Change the stroke of the L2/R2 buttons
You can adjust the stroke (trigger length/stop) of the
L2/R2 buttons, which is how far you can push down
the buttons.
To adjust this, move the L2/R2 stop sliders on the back of
your controller.
When the stop sliders are set to short or medium,
trigger eects will not be available.
long stroke
medium stroke
short stroke
Set up a profile
You can save stick sensitivity, vibration strength, button
assignments, and other controller settings as a profile.
• Assign your favorite profiles to a shortcut to quickly
switch between them during a game. Use the Fn button
to switch profiles.
• Assigned profiles are saved to your controller. Take your
controller with you and play with your profile on any PS5
console.
To set up a profile, go to your PS5 home screen and select
Settings > Accessories > DualSense Edge wireless
controller.
For more details on setting up a profile, refer to the
PS5 User’s Guide ( page 22).

17
Use the controller with a wired
connection
To use the controller with a wired connection, you first
need to set the connection method. From the PS5 home
screen, select Settings > Accessories > Controller
(General) > Communication Method, and then select
Use USB Cable.
Lock the USB cable to controller
You can lock the USB cable to the controller to stop the
cable from detaching. Open the connector housing and
place the USB cable inside so that the connector protrudes
from the outside. Then, close the connector housing.
Once you connect the USB cable to the controller, use the
connector housing’s slider to lock and unlock the USB
cable to your controller.
The connector housing is compatible only with the
included USB cable.
Charge the controller
While your PS5 console is on or in rest mode, connect the
controller to your console using the included USB braided
cable. When charging the controller in rest mode, the light
bar on the controller slowly blinks orange. When charging
is complete, the light bar turns o.
• To charge the controller while in rest mode, you
have to configure the settings. From the PS5 home
screen, select Settings > System > Power Saving
> Features Available in Rest Mode > Supply Power
to USB Ports, and then select a setting other than
O.
• You can also charge the controller by connecting it
to your computer or other USB device using a USB
cable. Be sure to use a USB cable that complies with
USB standards. You may not be able to charge your
controller on some devices.
Charging the controller in
the carrying case
You can charge the controller
while it is stored in the carrying
case.Open the flap on the back
of the case and connect the USB
cable to the controller.
EN

18
Use and handling
Care and cleaning
Follow the precautions below to help prevent the product
exterior from deteriorating or discoloring.
• Do not apply volatile substances such as insecticide.
• Do not allow rubber or vinyl materials to be in prolonged
contact with the product.
• Do not use thinner, benzine, or alcohol. Avoid using
wipes, chemical cloths, and other products that contain
such substances.
End of life product recycling
The product is made of many materials that may be
recycled. The controller contains a lithium ion battery.
Follow local regulations when disposing of the product.
Sony products can be recycled for free in the United States
and Canada by dropping the product o at a number of
nationwide locations. Visit
www.sony.com/ecotrade for details.
Never disassemble or modify the product
or accessories unless authorized in this
manual
Use the product and accessories according to the
instructions in this manual. No authorization for the
analysis or modification of the product, or the analysis
and use of its circuit configurations, is provided.
Handling the controller
• Charge in an environment where the temperature range
is between 10 °C and 30 °C (50 °F and 86 °F). Charging
may not be as eective when performed in other
environments.
• The battery has a limited lifespan. Battery duration will
gradually decrease with repeated usage and age.
Battery life also varies depending on the storage
method, usage state, environment, and other factors.
• When the controller is not used for an extended period
of time, it is recommended that you fully charge it at
least once a year in order to maintain battery
functionality.
• The product and its parts are made from metal and
plastic materials. When disposing of the product, follow
local regulations for the proper disposal of such
materials.

19
Compliance information
–Increase the separation between the equipment and
receiver.
–Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment. For assistance with this product, visit
playstation.com/help. The phone number in the supplier’s
declaration of conformity is only for FCC electrical
interference inquiries.
Supplier’s Declaration of Conformity
Trade Name : SONY
Model No. : CFI-ZCP1
Responsible Party : Sony Electronics Inc.
Address : 16535 Via Esprillo, San Diego, CA 92127 U.S.A.
Telephone No. : 858-942-2230 (Only for FCC electrical
interference inquiries)
This device complies with Part 15 of the FCC Rules and
Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This Class B digital apparatus complies with Canadian
ICES-003.
FCC and ISED Canada Notice
This equipment complies with FCC and ISED Canada
radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS-102 of the ISED Canada radio
frequency (RF) Exposure rules. This equipment should be
installed and operated keeping the radiator at least 10 mm
or more away from person’s body excluding extremities:
hands, wrists, feet and ankles. This transmitter must not be
co-located or operated in conjunction with any other
antenna or transmitter.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
–Reorient or relocate the receiving antenna.
EN

20
System and device software
• The device software of the controller are licensed to you
under the terms of a separate end user license
agreement. For details, visit
doc.dl.playstation.net/doc/ps5-eula/.
• Always update the system software of your PS5 console
and the device software of the controller to the latest
version.
Copyright and trademarks
“”, “PlayStation”, “PS5”, “DualSense Edge” and
“PlayStation Shapes Logo” are registered trademarks or
trademarks of Sony Interactive Entertainment Inc.
“SONY” and “ ” are registered trademarks or
trademarks of Sony Group Corporation.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by Sony Interactive Entertainment Inc. is under
license. Other trademarks and trade names are
those of their respective owners.
Information about open source software is available at
doc.dl.playstation.net/doc/ps5-oss/.
All other trademarks are the property of their respective
owners.
Specifications
Design and specifications are subject to change without
notice. The operating instructions may vary depending
on which software version you use, whether the system
software of your PS5 console, or the device software of
the controller. The actual product may vary from the
illustrations in this manual.
Controller
Input power rating 5 V 1,500 mA
Battery type Built-in lithium-ion battery
Battery voltage 3.7 V
Battery capacity 1,050 mAh
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Mass Approx. 325 g (11.5 oz)
Stick Module
External dimensions Approx. 30 × 31 × 40mm (1.2 × 1.2 ×
1.6 in) (width × height × depth)
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Mass Approx. 15 g (0.5 oz)
Included USB cable
Company: SONY / Part No.: 1-016-822-**
* represents a number between 0 and 9.