Sony HCD-ZUX10D User manual

SERVICE MANUAL
DVD DECK RECEIVER
SPECIFICATIONS
Ver. 1.3 2009.06
Model Name Using Similar Mechanism HCD-GNZ777D/GNZ888D
DVD Section CD Mechanism Type CDM74HF-DVBU101
Optical Pick-up Name KHM-313CAB/C2NP
Tape Section Model Name Using Similar Mechanism HCD-GN1100D
9-887-800-04
2009F04-1
© 2009.06
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
E Model
Australian Model
• HCD-ZUX10D is the tuner, deck, DVD
and amplifier section in LBT-ZUX10D.
Amplifier section
The following are measured at AC 120, 127,
220, 240V 50/60 Hz
Power Output (rated):
170 W + 170 W (6 Ω, 1 kHz, 1% THD)
RMS output power (reference)
Front speaker:
260 W + 260W (per channel at 6 Ω,
1 kHz, 10% THD)
Center speaker:
80 W (per channel at 6 Ω, 1 kHz,
10% THD)
Surround speaker:
260 W + 260W (per channel at 6 Ω,
1 kHz, 10% THD)
Inputs
VIDEO INPUT:
VIDEO: 1 Vp-p, 75 ohms
AUDIO L/R: Voltage 250 mV,
impedance 47 kilohms
TV/SAT AUDIO IN L/R:
Voltage 250 mV/450 mV, impedance
47 kilohms
MIC 1 or 2:
Sensitivity 1 mV, impedance
10 kilohms
Outputs
AUDIO OUT:
Voltage 250 mV, impedance 1 kilohm
VIDEO OUT:
Max. output level 1 Vp-p, unbalanced,
Sync. negative load impedance
75 ohms
COMPONENT VIDEO OUT:
Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
S VIDEO OUT:
Y: 1 Vp-p, unbalanced, Sync. negative
C: 0.286 Vp-p, load impedance
75 ohms
PHONES:
accepts headphones of 8 ohms or more
SUBWOOFER OUT:
Voltage 1 V, impedance 1 kilohm
– Continued on next page –
HCD-ZUX10D

2
HCD-ZUX10D
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Disc player section
System
Compact disc and digital audio and
video system
LaserSemiconductor laser (DVD: λ=
650 nm, CD: λ= 790 nm)
Emission duration: continuous
Frequency response
DVD (PCM 48 kHz): 2 Hz – 22 kHz
(±1 dB)
CD: 2 Hz – 20 kHz (±0.5 dB)
Video color system format
Latin American models: NTSC
Other models: NTSC and PAL
Tape deck section
Recording system
4-track 2-channel stereo
Frequency response
50 – 13,000 Hz (±3 dB),
using Sony TYPE I tape
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz (50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Latin American and Oceanian models:
530 – 1,710 kHz (with the interval set
at 10 kHz)
531 – 1,710 kHz (with the interval set
at 9 kHz)
Other models:
531 – 1,602 kHz (with the interval set
at 9 kHz)
530 – 1,610 kHz (with the interval set
at 10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
Oceanian models: 230 – 240 V AC,
50/60 Hz
Saudi Arabian model: 120 – 127 V, 220 V
or 230 – 240 V AC, 50/60 Hz, adjustable
with voltage selector
Other models: 120 V, 220 V or
230 – 240 V AC, 50/60 Hz, adjustable
with voltage selector
Power consumption
420 W
Dimensions (Approx.)
491 ×297.5 ×460 mm (w/h/d)
Mass (Approx.)
20 kg
Supplied accessories:
Remote Commander (2)
R6 (size AA) batteries (4)
AM loop antenna (1)
FM lead antenna (1)
Video cord (1)
Front speaker pads (8)
Surround speaker pads (8)
Center speaker pads (4)
Speaker cords (5)
Design and specifications are subject to
change without notice.
Ver. 1.3

3
HCD-ZUX10D
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 ˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
otherthan those specifiedhereinmay result in hazardous radiation
exposure.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 ˚C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
This appliance is
claassified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
Ver. 1.2

4
HCD-ZUX10D
MODEL IDENTIFICATION
– BACK PANEL –
Model Part No.
E3 3-100-831-0s
MY, SP 3-100-831-1s
AUS 3-100-831-2s
E2 3-100-831-3s
E51 3-100-831-4s
EA 3-100-831-5s
•Abbreviation
E2 : 120V AC area in E model
E3 : 240V AC area in E model
EA : Saudi Arabia model
E51 : Chilean and Peruvian model
AUS:Australian model
MY : Malaysia model
SP : Singapore model
PART No.
PLAYABLE DISCS
Type Characteristics Logo
DVD VIDEO • DVD VIDEO
•DVD-R*/-RW*/+R/+RW in
DVD VIDEO format
* also in video mode
VR mode • DVD-R/-RW in VR (Video
Recording) mode
VIDEO CD • VIDEO CD
•Super VCD
•CD-R/-RW in VIDEO CD or
Super VCD format
CD • AUDIO CD
•CD-R/-RW in AUDIO CD
format
DATA CD • CD-ROM/-R/-RW in DATA
CD format, containing MP3
audio tracks1), JPEG image
files2) or DivX video files3),
and conforming to ISO 96604)
Level 1 or Level 2, or Joliet
(expansion format).
DATA DVD • DVD-ROM/-R/-RW/+R/+RW
in DATA DVD format,
containing MP3 audio tracks1),
JPEG image files2) or DivX
video files3), and conforming
to UDF (Universal Disk
Format).
This system can also play back discs with the following disc logos:
1) MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ISO/
MPEG which compresses audio data. MP3 audio tracks must be in MPEG
1 Audio Layer 3 format.
2) JPEG image files must conform to the DCF image file format. (DCF
“DesignruleforCameraFile System”: Image standards fordigitalcameras
regulated by Japan Electronics and Information Technology Industries
Association (JEITA)).
3) DivX video files must be recorded in DivX format with the extension
“.AVI” or “.DIVX”.
4) A logical format of files and folders on CD-ROMs, defined by ISO
(International Organization for Standardization).
DivX®is a video file compression technology, developed by DivX, Inc..
DivX, DivX Certified, and associated logos are trademarks of DivX, Inc.
and are used under license.
“DVD+RW”, “DVD-RW”, “DVD+R”, “DVDVIDEO”, and the “CD” logos
are trademarks.
Ver. 1.3

5
HCD-ZUX10D
1. SERVICING NOTES
Loading Panel .................................................................. 6
2. GENERAL
Guide to Parts and Controls............................................. 7
3. DISASSEMBLY
3-1. Side R Panel, Side L Panel .............................................. 16
3-2. Top Case Section ............................................................. 16
3-3. Back Panel Section .......................................................... 17
3-4. Loading Panel .................................................................. 17
3-5. Front Panel Section ......................................................... 18
3-6. Tape Mechanism Deck .................................................... 18
3-7. Holder (TC-L), Holder (TC-R) ....................................... 19
3-8. Power AMP Section ........................................................ 19
3-9. Main Board...................................................................... 20
3-10. FL Board, Power LED Board .......................................... 20
3-11. Illumination Board, VOL Board...................................... 21
3-12. MIC Board, VR Board, Base R LED Board ................... 21
3-13. HP-Video Board, Base L LED Board ............................. 22
3-14. Center Key Board, Beat Creator Board,
X-Round Board ............................................................... 22
3-15. Bracket (Trans) ................................................................ 23
3-16. DMB16 Board, Video Board ........................................... 23
3-17. DVD Mechanism Deck ................................................... 24
3-18. Driver Board, SW Board ................................................. 24
3-19. Optical Pick-Up ............................................................... 25
3-20. Sensor Board ................................................................... 25
3-21. Motor (TB) Board ........................................................... 26
3-22. Motor (LD) Board ........................................................... 26
4. TEST MODE.............................................................. 27
5. MECHANICAL ADJUSTMENTS ....................... 32
6. ELECTRICAL ADJUSTMENTS ......................... 32
7. DIAGRAMS
7-1. Block Diagram – RF/Servo Section – ............................. 35
7-2. Block Diagram – Video Section – ................................... 36
7-3. Block Diagram – Tape/Tuner Section – .......................... 37
7-4. Block Diagram – Main Section – .................................... 38
7-5. Block Diagram – Effector Section – ............................... 39
7-6. Block Diagram – AMP Section – .................................... 40
7-7. Block Diagram – Display/Power Section –..................... 41
7-8. Printed Wiring Boards – Driver Section –....................... 45
7-9. Schematic Diagram – Driver Section – ........................... 46
7-10. Printed Wiring Board – Main Section – .......................... 47
TABLE OF CONTENTS
7-11. Schematic Diagram – Main Section (1/4) – .................... 48
7-12. Schematic Diagram – Main Section (2/4) – .................... 49
7-13. Schematic Diagram – Main Section (3/4) – .................... 50
7-14. Schematic Diagram – Main Section (4/4) – .................... 51
7-15. Printed Wiring Board – DMB16 Section (1/2) –............. 52
7-16. Printed Wiring Board – DMB16 Section (2/2) –............. 53
7-17. Schematic Diagram – DMB16 Section (1/6) – ............... 54
7-18. Schematic Diagram – DMB16 Section (2/6) – ............... 55
7-19. Schematic Diagram – DMB16 Section (3/6) – ............... 56
7-20. Schematic Diagram – DMB16 Section (4/6) – ............... 57
7-21. Schematic Diagram – DMB16 Section (5/6) – ............... 58
7-22. Schematic Diagram – DMB16 Section (6/6) – ............... 59
7-23. Printed Wiring Boards – HP-Video/MIC Section – ........ 60
7-24. Schematic Diagram – HP-Video/MIC Section –............. 61
7-25. Printed Wiring Board – Karaoke Section – ..................... 62
7-26. Schematic Diagram – Karaoke Section –........................ 63
7-27. Printed Wiring Board –Video Section – ......................... 64
7-28. Schematic Diagram – Video Section – ............................ 65
7-29. Printed Wiring Board –VR Section – ............................. 66
7-30. Schematic Diagram – VR Section – ................................ 67
7-31. Printed Wiring Board – CenterAMP Section – .............. 68
7-32. Schematic Diagram – Center AMP Section – ................. 69
7-33. Printed Wiring Board – Effector Section –...................... 70
7-34. Schematic Diagram – Effector Section – ........................ 71
7-35. Printed Wiring Board – Power AMP Section – ............... 72
7-36. Schematic Diagram – Power AMP Section – .................. 73
7-37. Printed Wiring Board – FL Section – .............................. 74
7-38. Schematic Diagram – FL Section –................................. 75
7-39. Printed Wiring Boards – Key Section (1/2) –.................. 76
7-40. Printed Wiring Boards – Key Section (2/2) –.................. 77
7-41. Schematic Diagram – Key Section –............................... 78
7-42. Printed Wiring Boards – LED Section (1/2) – ................ 79
7-43. Printed Wiring Boards – LED Section (2/2) – ................ 80
7-44. Schematic Diagram – LED Section –.............................. 81
7-45. Printed Wiring Boards – Power Section – ....................... 82
7-46. Schematic Diagram – Power Section – ........................... 83
8. EXPLODED VIEWS
8-1. Main Section................................................................... 100
8-2. Front Panel Section (1) ................................................... 101
8-3. Front Panel Section (2) ................................................... 102
8-4. Front Panel Section (3) ................................................... 103
8-5. Top Case Section ............................................................ 104
8-6. Back Panel Section ......................................................... 105
8-7. Chassis Section ............................................................... 106
8-8. DVD Mechanism Section (1) ......................................... 107
8-9. DVD Mechanism Section (2) ......................................... 108
9. ELECTRICAL PARTS LIST............................... 109

6
HCD-ZUX10D SECTION 1
SERVICING NOTES
LOADING PANEL
gear (shaft)
1 Turn the gear (shaft) in the direction of the arrow.
3 loading panel
2

7
HCD-ZUX10D
SECTION 2
GENERAL This section is extracted from
instruction manual.
9
GB
Guide to parts and controls
Guide to parts and controls
This manual mainly explains operations using the remote, but the same operations can
also be performed using the buttons on the unit having the same or similar names.
123 6547
wh
wf
wd
wg
ws wa w; ql qk qj qh qg qfqd
qs
qaq;
9
8
wk
wl
wj
ed es ea e;
Continued
l
Top view
Front view

8
HCD-ZUX10D
10
GB
1"/1 (on/standby) (pages 18, 19,
20, 54, 77, 78, 84)
Press to turn the system on or off.
BBEAM MODE (page 71)
Press to change the lighting effect of
a beam.
CDVD (pages 19, 27, 56, 65, 71,
82)
TUNER/BAND (pages 53, 71)
TAPE A (pages 55, 71)
Press to select a function.
DFLANGER (pages 60, 79, 84)
DELAY (pages 60, 79, 84)
CHORUS (pages 61, 79, 84)
AQUA (pages 61, 79, 84)
Press to select an effector mode.
EDisplay (pages 13, 72, 85)
FIR Receptor (page 79)
GTV/SAT (pages 71, 76, 79)
VIDEO (pages 71, 77)
TAPE B (pages 55, 69, 71)
Press to select a function.
HDISPLAY (pages 71, 72)
Press to change the information in
the front panel display.
IGROOVE (page 58)
Press to reinforce the bass.
JFLAT (page 58)
MP3 EQ (page 58)
REGGAE (page 58)
HIP HOP (page 58)
TECHNO (page 58)
Press to select a preset effect.
KSOUND FIELD (page 59)
Press to select a sound field.
LFRONT BEAM (right) (pages 71,
79)
MMIC 1/2 LEVEL (pages 57, 65,
78)
Turn to adjust the microphone
volume.
ECHO LEVEL (page 65)
Turn to adjust the microphone echo
effect.
NMIC 1/2 (jack) (pages 57, 65, 78)
Connect the microphones.
OBOTTOM BEAM (right) (page 71)
PDisc tray (pages 13, 27, 80)
QOPERATION DIAL (pages 58,
63, 70)
Turn to select a setting.
RMASTER VOLUME (pages 27,
69, 78)
Turn to adjust the volume.
SPower illuminator (page 70)
TBOTTOM BEAM (left) (page 71)
UVIDEO INPUT (jacks) (page 75)
Connect an audio or video
component.
VPHONES (jack) (page 78)
Connect the headphones.
WFRONT BEAM (left) (pages 71,
79)
XEQ BAND/MEMORY (page 58)
Press to select a frequency band
when adjusting the graphic
equalizer.
YROCK (page 58)
POP (page 58)
JAZZ (page 58)
DANCE (page 58)
Press to select a preset effect.
USER EQ (page 58)
Press to select a user equalizer.

9
HCD-ZUX10D
11
GB
Guide to parts and controls
ZAMP MENU (page 70)
Press to change the spectrum
analyser display, adjust the
brightness of the display and built-in
beam or change the power
illuminator pattern.
wj A ZPUSH OPEN/CLOSE
(Eject A) (page 55)
Press to insert or eject a tape.
Deck A (page 55)
wk B PUSH ZOPEN/CLOSE
(Eject B) (page 55)
Press to insert or eject a tape.
Deck B (pages 55, 56, 69)
wl X-ROUND ON/OFF (pages 61,
62)
Presstoturnon or off theX-ROUND
mode.
X-ROUND MODE (pages 61, 62)
Press to select an X-ROUND mode.
MAX/JUMP MODE (page 62)
Presstoselectthe way of creating the
“MAX” and “JUMP” effect.
X-ROUND JOG (page 62)
Turn to change the sound movement
or the speed of the sound movement.
MAX PAD (page 62)
Press to enhance the sound.
JUMP PAD (page 62)
Press to switch the sound position to
the opposite direction.
e; DISC 1 ~ 3 (page 28)
Press to select a disc or switch to
DVD function from another source.
DISC SKIP/EX-CHANGE
(pages 19, 27, 28)
Press to exchange other discs during
playback.
ZOPEN/CLOSE (pages 19, 27,
80)
Press to load or eject a disc.
ea X(pause) (pages 27, 55)
Press to pause playback.
ENTER (pages 23, 31, 53, 58,
69, 84)
Press to enter the selection.
PROGRESSIVE (pages 21, 76,
82)
Presstoselectthe format ofthevideo
signals output from the
COMPONENT VIDEO OUT jacks.
CD SYNC (page 56)
Press to start CD Synchro Recording.
REC PAUSE/START (page 56)
Press to start manual recording.
DIRECTION (pages 55, 69)
Press to select the tape playback and
recording option.
Continued
l

10
HCD-ZUX10D
12
GB
es PRESET –/+ (page 53)
Press to select a preset station.
./> (go backward/go
forward) (pages 27, 38, 56, 84)
Press to select a track, chapter or
DivX video file.
TUNING –/+ (pages 53, 54)
Press to tune in a radio station.
m/M (rewind/fast
forward) (page 27)
Press to rewind or fast forward.
Press to watch frame by frame when
playback is paused.
nN (play) (pages 27, 55, 78)
Press to start playback.
x(stop) (pages 27, 53, 55)
Press to stop playback or recording.
ed BEAT ON/OFF (page 63)
Press to turn on or off the rhythms of
the beat.
BEAT LEVEL (page 63)
Press to adjust the beat level.
BEAT SPEED (page 64)
Press to change the beat speed.
BEAT PATTERN (page 64)
Press to select the rhythms of the
beat.
BPM CONTROL (page 64)
Press to input the tempo of the audio
source.
PAD A/PAD B (page 63)
Press to add percussion sound.

11
HCD-ZUX10D
13
GB
Guide to parts and controls
Display
AIndicators for the disc tray (page 27).
“”lights up when the disc is
selected. “ ” lights up when there is
a disc on the disc tray. “1”, “2” and
“3” light up when the system is turned
on.
BIndicators for the DVD function
(page 27).
“DVD” lights up when DVD VIDEO,
DVD-R/-RW in VR mode or DATA
DVD is detected. “CD” lights up
when AUDIO CD or DATA CD is
detected. “VCD” lights up when
VIDEO CD or Super VCD is
detected. “MP3” lights up when MP3
audio tracks are played back.
CLights up when the color system of
the video output is NTSC (page 20).
DLights up when “P AUTO” or
“P VIDEO” is selected (page 21).
E“”lights up when DTS source is
played back (page 50).
“;DIGITAL”lightsup whenDolby
Digital source is played back
(page 50).
FLights up when the elapsed playing
time and the remaining playing time
for the title or chapter is displayed
(page 72).
GIndicators for the tuner band
(page 53).
HDisplays the current status and
information (page 72).
ILightsupwhenVIDEOCD withPBC
functions is played back (page 30).
JIndicators for the TUNER function
(page 53).
KIndicators for the BEAT BLEND
mode (page 63).
LIndicators for the X-ROUND mode
(page 61).
MIndicators for the TAPE function
(page 55).
“A” and “B” lights up when the
system is turned on.
“b” or “B” lights up when there is a
tape in the deck and indicates the tape
playbackdirection.“RELAY”, “g”
and “j” indicates the tape
playback option.
NIndicators for the recording type and
status (page 56).
OLights up when the Play Timer or
Recording Timer is set (page 69).
PLights up when the Sleep Timer is
activated (page 69).
QIndicators for sound field (page 59).
“;PL”or“;PL II” lights up when
Pro Logic decoding or Pro Logic II
Movie/Music decoding is performed.
“VIRTUAL” lights up when “HP
VIRTUAL” is selected. “VIRTUAL”
and “DCS” light up when
“V.M.DIM.” is selected. “LINK”
lights up when “LINK” is selected.
RLights up when Karaoke Mode is
turned on (page 65).
S“GROOVE” lights up when
“GROOVE ON” is selected.
“Z GROOVE” lights up when
“Z-GROOVE ON” is selected
(page 58).
qs
qa
qd
q;
q
f
qhqj
qkql
23546
7891
q
g
RELAY
w;
Continued
l

12
HCD-ZUX10D
14
GB
TIndicates the selected play mode
(page 31).
“SHUF” lights up when Shuffle Play
is activated. “PROGRAM” lights up
when Program Play is activated.
“REP” lights up when Repeat Play is
set to “ALL DISCS”, “ONE DISC”,
“ALBUM” or “ON”. “REP 1” lights
up when Repeat Play is set to
“TITLE”, “CHAPTER”, “TRACK”
or “FILE”.
Remote (RM-AMU005)
1THEATRE SYNC (page 26)
Press to operate the THEATRE
SYNC function.
BTV "/1 (on/standby) (page 22)
Press to turn the TV on or off.
"/1 (on/standby) (pages 18, 23,
78)
Press to turn the system on or off.
CDISC SKIP (page 28)
Press to select the next disc.
DFUNCTION +/– (pages 27, 53,
55, 76)
Press to select a function.
EPICTURE NAVI (pages 36, 38)
Press to search for a scene or a JPEG
image file.
FREPEAT/FM MODE (pages 34,
54, 83)
Press to change the Repeat Play
setting.
Press to select the FM monaural or
stereo reception.
GAUDIO (pages 29, 65, 74)
Press to select the audio format.
HSUBTITLE/D.TUNING
(pages 29, 54)
Press to turn on or off or change the
language of the subtitle.
Press to enter direct tuning mode.
IANGLE (page 28)
Press to change the angle.
J+/– (pages 25, 27)
Press to select an album.
KDVD/TUNER MENU (pages 34,
38, 53)
Press to display the menu of the
DVD VIDEO.
Press to preset a radio station.
LSOUND FIELD (page 59)
Press to select a sound field.
MTV VOL +/–*(page 22)
Press to adjust the TV volume.
VOLUME +/–*(pages 27, 69, 78)
Press to adjust the volume.
NDISPLAY (pages 31, 47, 66,
90)
Press to turn on or off or change the
Control Menu display on the TV
screen.
q;
qh
qj
qk
ql
wa
wf
wg
qg
qf
qs
qa
4
3
2
5
6
7
w;
wd
ws
wh
8
9
qd
1

13
HCD-ZUX10D
15
GB
Guide to parts and controls
OTV CH +/– (page 22)
Press to select a TV channel.
PRESET +/– (page 53)
Press to select a preset station.
./> (go backward/go
forward) (pages 27, 38, 56, 84)
Press to select a track, chapter or
DivX videofile and toadjust the time
when setting the clock or timer.
cSTEP C(page 28)
Press to watch one frame at a time.
REPLAY /ADVANCE
(page 28)
Press to replay the previous scene or
briefly fast forward the current
scene.
TUNING +/– (pages 53, 54)
Press to tune in a radio station.
SLOW /SLOW (page 28)
Press to watch frame by frame.
m/M (rewind/fast forward
(page 27)
Press to rewind or fast forward.
H*(play) (pages 27, 55, 78)
X(pause) (pages 27, 55)
x(stop) (pages 27, 53, 55)
Press to start, pause or stop playback.
PTV (page 22)
Hold down TV and press the button
you want to operate the TV.
QORETURN (pages 30, 37, 38)
Press to return to the previous
display.
RV/v/B/b (pages 23, 31, 53, 66,
69)
Press to select the settings.
ENTER (pages 23, 31, 53, 58,
69)
Press to enter the selection.
SDVD TOP MENU (page 34)
Press to display the DVD title.
T-/-- (page 22)
Press to enter a double digit channel
number for TV.
CLEAR (pages 24, 25, 32, 39)
Presstocancel the playmodeor clear
a mistake when you press the
incorrect numeric button.
UNumeric buttons*(pages 22, 27,
44, 53)
Press to tune or preset a radio station,
enter a track or file number, etc.
VKEY CONTROL 2/#(page 67)
SCORE (page 67)
KARAOKE MODE (page 65)
KARAOKE PON (page 67)
Press to enjoy the karaoke function.
WDISPLAY (pages 71, 72)
Press to change the information in
the front panel display.
wf TIME/TEXT (pages 72, 73)
Press to check the elapsed playing
time, remaining time, title, etc.
wg TV INPUT (page 22)
Press to switch the TV’s input
source.
SLEEP (pages 25, 69)
Press to activate the Sleep Timer.
wh TIMER MENU (pages 23, 69)
Press to set the clock and timer.
Continued
l

14
HCD-ZUX10D
16
GB
*The numeric button 5, TV VOL +, VOLUME
+ and Hbuttons have a tactile dot. Use the
tactile dot as a reference when operating the
system.
X-TRANCE PRO remote
(RM-AMU007)
1"/1 (on/standby) (pages 18, 23,
78)
Press to turn the system on or off.
BX-ROUND ON/OFF (pages 61,
62)
Presstoturnon or offthe X-ROUND
mode.
X-ROUND MODE (pages 61, 62)
Press to select an X-ROUND mode.
MAX PAD (page 62)
Press to enhance the sound.
JUMP PAD (page 62)
Press to switch the sound position to
the opposite direction.
X-ROUND +/– (page 62)
Press to change the sound movement
or the speed of the sound movement.
3PAD A (page 63)
PAD B (page 63)
Press to add percussion sound.
4FRONT BUILT-IN BEAM
(page 71)
BOTTOM BUILT-IN BEAM
(page 71)
Press to change the lighting effect of
the beam.
E–./>+ (go backward/go
forward) (pages 27, 38, 56, 84)
Press to select a track or file.
N(play) (pages 27, 55, 78)
X(pause) (pages 27, 55)
x(stop) (pages 27, 53, 55)
Press to start, pause or stop playback.
FBEAT LEVEL (page 63)
Press to adjust the beat level.
BEAT PATTERN +/– (page 64)
Press to select the rhythms of the
beat.
GVOLUME +/–*(pages 27, 69, 78)
Press to adjust the volume.
8BEAT ON/OFF (page 63)
Press to turn on or off the rhythms of
the beat.
BEAT SPEED +/– (page 64)
Press to change the beat speed.
IGROOVE (page 58)
Press to reinforce the bass.
JSOUND EFFECT (page 61)
Press to select an effector mode.
KFUNCTION (pages 27, 53, 55,
76)
Press to select a function.
*The VOLUME + button has a tactile dot. Use
the tactile dot as a reference when operating
the system.
q;
1
4
6
qa
7
8
9
2
3
5

15
HCD-ZUX10D
Note: Disassemble the unit in the order as shown below.
SECTION 3
DISASSEMBLY
3-21. MOTOR (TB) BOARD
(Page 26)
3-22. MOTOR (LD) BOARD
(Page 26)
3-1. SIDE R PANEL,
SIDE L PANEL
(Page 16)
3-2. TOP CASE SECTION
(Page 16)
SET
3-3. BACK PANEL SECTION
(Page 17)
3-18. DRIVER BOARD,
SW BOARD
(Page 24) 3-19. OPTICAL PICK-UP
(Page 25)
3-4. LOADING PANEL
(Page 17)
3-5. FRONT PANEL SECTION
(Page 18)
3-7. HOLDER (TC-L),
HOLDER (TC-R)
(Page 19)
3-10. FL BOARD,
POWER LED BOARD
(Page 20)
3-11. ILLUMINATION BOARD,
VOL BOARD
(Page 21)
3-12. MIC BOARD,
VR BOARD,
BASE R LED BOARD
(Page 21)
3-20. SENSOR BOARD
(Page 25)
3-17. DVD MECHANISM DECK
(Page 24)
3-15. BRACKET (TRANS)
(Page 23)
3-14. CENTER KEY BOARD,
BEAT CREATOR BOARD,
X-ROUND BOARD
(Page 22)
3-13. HP-VIDEO BOARD,
BASE L LED BOARD
(Page 22)
3-6. TAPE MECHANISM DECK
(Page 18)
3-9. MAIN BOARD
(Page 20)
3-16. DMB16 BOARD,
VIDEO BOARD
(Page 23)
3-8. POWER AMP SECTION
(Page 19)

16
HCD-ZUX10D
3-2. TOP CASE SECTION
Note: Follow the disassembly procedure in the numerical order given.
3-1. SIDE R PANEL, SIDE L PANEL
1 two screws
(case 3 TP2
)
6 two screws
(case 3 TP2)
2 screw
(case 3 TP2)
7 screw
(case 3 TP2)
3 three screws
(+BVTP 3
× 8)
8 three screws
(+BVTP 3
× 8)
5 side R panel
0 side L panel
4
9
1 four screws
(+BVTP 3
× 8)
2
5
CN381 (3P)
3 CN200 (6P)
6 CN380 (8P)
7 top case section
4 wire (flat type) (11 core)
(CN101)

17
HCD-ZUX10D
3-3. BACK PANEL SECTION
3-4. LOADING PANEL
9 three screws
(+BVTP 3
× 8)
0 four screws
(+BVTP 3
× 8)
8 four screws
(+BVTP 3
× 8)
7 three screws
(+BVTP 3
× 8)
4 two screws
(+BVTP 3
× 8)
6 three screws
(+BVTP 3
× 8)
qs CN600 (2P)
qd back panel section
qa
3
CN1200 (3P)
5 PRIMARY board
1 wire (flat type) (9 core
)
(CN382)
2 wire (flat type) (19 core)
(CN1502)
gear (shaft)
1 Turn the gear (shaft) in the direction of the arrow.
3 loading panel
2

18
HCD-ZUX10D
3-6. TAPE MECHANISM DECK
3-5. FRONT PANEL SECTION
6 five screws
(+BVTP 3
× 10)
lug
lug
lug
0 front panel section
7
2
screw
(+BVTP 3
× 8)
3 screw
(+BVTP 3
× 8)
4 screw
(+BVTP 3
× 8)
5 CN602 (4P)
9 CN901 (5P)
8 CN502 (5P)
1 wire (flat type) (17 core)
(CN100)
1 three screws
(+BVTP 2.6 (3CR))
wiring stopper
2 two screws
(+BVTP 2.6 (3CR))
4 three screws
(+BVTP 2.6 (3CR))
5 three screws
(+BVTP 2.6 (3CR)
)
3 shild plate (TCM)
6 tape mechanism deck
top case assy

19
HCD-ZUX10D
3-8. POWER AMP SECTION
3-7. HOLDER (TC-L), HOLDER (TC-R)
1 damper
3 holder (TC-L)
6 holder (TC-R)
2 spring (A)
top case ass
y
5 spring (B)
4 damper
5 two screws
(+BVTP 3
× 8)
3 screw
(+BVTP 3
× 8)
6 two screws
(+BVTP 3
× 8)
4 two screws
(+BVTP 3
× 8)
7 two screws
(+BVTP 3
× 8)
1 CN600 (6P)
2 CN602 (4P)
8 CN501 (12P)
qs POWER AMP sectio
n
9 CN253 (9P)
qa CN255 (5P)
0 CN582 (3P)

20
HCD-ZUX10D
3-10. FL BOARD, POWER LED BOARD
3-9. MAIN BOARD
9 two screws
(+BVTP 3
× 8)
qf MAIN board
qd CN502 (5P)
8 CN251 (5P)
qa CN551 (5P)
qs CN550 (5P)
7 CN252 (2P)
3 CN1213 (8P)
4 wire (flat type) (13 core)
(CN105)
5 wire (flat type) (13 core)
(CN104)
6 wire (flat type) (21 core
)
(CN521)
2 wire (flat type) (13 core)
(CN105)
1 wire (flat type) (17 core)
(CN100)
0
1 two screws
(+BVTP 2.6 (3CR))
2 two screws
(+BVTP 2.6 (3CR))
4 two screws
(+BVTP 2.6 (3CR))
5 two screws
(+BVTP 2.6 (3CR))
6 four screws
(+BVTP 2.6 (3CR)
)
3 POWER LED board
7 FL board
8 CN905 (9P)
0 CN906 (10P)
qa CN902 (8P)
qs CN918 (3P)
9 CN917 (3P)