Sound Storm SD354 User manual

3.6” In-Dash DVD/MP3/CD Receiver
with USB, SD Memory Card Ports
and Front Panel AV Input

E - 1
1. HANDLING COMPACT DISCS
MOISTURE CONDENSATION
NOTES ON CDs
P. 2
P. 3
P. 4
P. 1 P. 6
P. 7
1.
2.
3.
4.
5.
Stickers that are beginning
to peel away leave a
sticky residue (P.6).
Labels are attached (P.7).
On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit.
Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for
about an hour until the moisture has evaporated.
A dirty or defective disc may cause sound
dropouts while playing. To enjoy optimum
sound, handle the disc as follows.
Handle the disc by its edge. To keep the disc
clean, do not touch the surface (P.1).
Do not stick paper or tape on the disc (P.2).
Before playing, clean the discs with an
optional cleaning cloth. Wipe each disc from
the centre out (P.4).
Do not use solvents such as benzine,
thinner,commercially available cleaners, or
antistatic spray intended for analog discs.
Do not expose the discs to direct sunlight or
heat sources such as hot air-ducts, or leave
them in a car parked in direct sunlight where
there can be a considerable rise in
temperature inside the car (P.3).
Do not use CDs with old labels that are
beginning to peel off.
Do not use CDs with labels or stickers
attached.
**************
*******
*******
*******
*******
*******
*******
*******
*******
Do Not Use Special Shape CDs
Be sure to use round shape CDs only. Do
not use any special shape CDs. Use of
special shape CDs may cause the unit to
malfunction.(P.8).
P. 8
CD-Rs and CD-RWs which have not
undergone finalization processing cannot
be played. (For more information on
finalization processing, refer to the manual
for your CD-R/CD-RW writing software or
CD-R/CD-RW recorder.) Additionally,
depending on the recording status, it may
prove impossible to play certain CDs
recorded on CD-R or CD-RW.
E - 1
P. 5
NOTES ON DISCS
If you use the discs explained below, the sticky
residue can cause the CD to stop spinning and
may cause malfunction or ruin your discs.
Do not use CDs that have a sticky residue on the
surface (for example, from peeled-off stickers or
from ink, or glue leaking from under the
stickers).
****
*******
******* *******
*******
Paste or sticky residue.

E - 2
2. INSTALLATION
Before finally installing the unit, connect the wiring temporarily and make sure it is all
connected up properly and the unit and system work properly.
Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
Avoid installing the unit where it would be subject to high temperature, such as from direct
sunlight, or from hot air, from heater, or where it would be subject to dust dirt or excessive
vibration.
Be sure to remove the front panel before installing the unit.
DIN FRONT/REAR-MOUNT
This unit can be property installed either from “Front” (conventional DIN Front-mount) or
“Rear”(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit
chassis). For details, refer to the following illustrated installation methods A and B.
DIN FRONT-MOUNT (Method A)
Installation the unit
1. Dashboard
2. Holder
After inserting the half sleeve into the dashboard,
select the appropriate tab according to the
thickness of the dashboard material and bend
them inwards to secure the holder in place.
3. Screw
30
1
7
4
23
5
61. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (4x12mm)
5. Screw
6. Support Strap
Be sure to use the support strap to secure the
back of the unit in place. The strap can be bent by
hand to the desired angle.
7. Plain washer
182
53
12
3
Removing the unit
a. Frame
b. Insert fingers into the groove in the front of frame
and pull out to remove the frame. (When re-
attaching the frame, point the side with a groove
down wards and attach it.)
c. Insert the levers supplied with the unit into the
grooves at both sides of the unit as shown in
figure until they click. Pulling the levers makes it
possible to remove the unit from the dashboard.
a
b
c
Trim Plate Installation:
Push the trim plate against the chassis until it is fitted.
You must do this before you install the front panel, otherwise it can't be attached.
RCA LINE OUT JACK(OPTION)

E - 3
DIN REAR-MOUNT (METHOD B)
Installation using the screw holes on the sides of the unit.
Fastening the unit to the factory radio mounting bracket.
1. Select a position where the screw holes of
the bracket and the screw holes of the main
unit become aligned (are fitted) and tighten
the screws at 2 places on each side.
2. Screw(must not use more than 6mm length)
3. Factory radio mounting bracket.
4. Dashboard or Console
5. Hook (Remove this part)
Note: the mounting box, outer trim ring,
and half-sleeve are not used for method B
installation.
5
2
4
3
2
5
PANEL OPEN/CLOSE OPERATION
1. Press Open button
2. The CD slot will be accessible.
3. After CD is loaded or unloaded return the panel to its original position.
12
RESET
CDIN

E - 4
Attaching the Detachable Control panel (D.C.P.)
3. DETACHABLE CONTROL PANEL (D.C.P.)
PUSH
B
A
DC
1. Attach the panel at the Left side first,
with point B on the main unit touching
point A on the D.C.P
(As shown on the diagram).
2. And then also attach the panel at the
right side , with point C on the main unit
touching point D on the D.C.P as well
(As shown on the diagram)
3. Then press the left side of D.C.P onto the
main unit until a “click” sound is heard.
Removing The Detachable Control Panel (D.C.P.).
OPEN
BUTTON
D.C.P.
1. Turn the power off.
2. Press the panel open button,
the D.C.P will be fold down.
3. Push hard the D.C.P in the left direction
until the point D at the right side of D.C.P
is came off the main unit
(As shown on the diagram).
3. Remove the D.C.P.
D

CAUTION
DO NOT insert the D.C.P from the right side. Doing so may damage it.
The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and be careful not
to drop it or subject it to strong shocks.
When the open button is pressed and the D.C.P is unlocked, the car's vibrations may cause it to fall. To prevent
damage to the D.C.P, always store it in a protective case after detaching it.
The rear connector that connects the main unit and the D.C.P is an extremely important part. Be careful not to
damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Note:
If the D.C.P is dirty, wipe off the dirt with soft,
dry cloth only. And use a cotton swab soaked
in isopropyl alcohol to clean the socket on the
back of the D.C.P.
Socket
E - 5

E - 6
4. ELECTRICAL CONNECTION
a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a
converter will be necessary).
b. Before starting wiring connections, disconnect the power supply by removing the fuse from
the fuse box.
c. Connect the power wire to one of the extra terminals of the fuse box.
d. Connect the black ground wire to a metal part of the car. It is important to make good contact.
e. Make other wiring connections as shown.
FUSE
Fuse Replacement:
To replace the fuse, pull out the blown fuse
from the socket. Insert a new one with same rating
(CAR UNIT BACK SIDE)
Initial installation of the unit when all wiring is completed.
All the function buttons do not operate.
Error symbol on the display.
RESET BUTTON
RED
WHITE
(REAR)
RCA OUTPUT
RED
WHITE
(FRONT)
RCA OUTPUT
ANTENNA
CONNECTOR
GREY
BLACK
VIDEO OUT (1)/(2)
AUDIO IN RED
WHITE
YELLOW
YELLOW
VIDEO IN YELLOW
REVERSE VIDEO IN YELLOW
GREY
GREY / BLACK
VIOLET
VIOLET / BLACK
FRONT
RIGHT
SPEAKER
REAR
RIGHT
SPEAKER
WHITE
WHITE / BLACK
GREEN
GREEN/BLACK
FRONT
LEFT
SPEAKER
REAR
LEFT
SPEAKER
MAIN UNIT
BLUE
AUTO ANT.
SUB-WOOFER
GOUND ( )
BLUE
(+)
12V+
SWITCHED
12V+
CONSTANT
YELLOW
(FUSED)
BLACK
RED
GREY
PINK
PARKING BRAKE(-)
ORANGE
REVERSE(+12V)
OVERRIDE WIRE
f. If your car does not have ISO connector, you can purchase it from car accessory shops.
Notes: INCORRECT WIRING OR OPERATION WILL VOID THE WARRANTY OF THIS UNIT.
The RESET button is located on the main unit (as shown on the diagram). Press it vertically
with a ballpoint pen or metal object to activate it. The reset button should be activated for the
following reasons:
Note: If you press the RESET button, and the unit still cannot function normally, please use a
cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel.

5
E - 7
POWER
BUTTON
MODE
BUTTON
INFRARED
REMOTE
SENSOR
MUTE
BUTTON
LOCAL/
DX
BUTTON
SCAN
BUTTON
FM
STEREO /
MONO
BUTTON
PANEL
OPEN
BUTTON
ENCODER
VOLUME
KNOB
PRESET MEMORY BUTTONS
(M1-M6)
AMS
BUTTON
BAND/
LOUDNESS
BUTTON
CD
PAUSE
BUTTON
FUNCTION
SELECT
BUTTON
TUNING /
SEEK
UP/DOWN
NEXT/BACK
BUTTON
CD
SCAN
BUTTON
CD
RANDOM
BUTTON
CD
REPEAT
BUTTON
DSP/
LEFT/
RIGHT
BUTTON
DISPLAY
BUTTON
APL/
NTSC/

E - 8
B. FUNCTION OF REMOTE
1. POWER BUTTON
2. PAL / NTSC /BAND BUTTON
3. PLAY / PAUSE BUTTON
4. NUMERIC BUTTONS
5. REPEAT BUTTON
6. REPEAT A - B BUTTON
7. VOLUME UP / DOWN BUTTONS
8. MUTE BUTTON
9. FUNCTION SELECT BUTTON
10. MODE BUTTON
11. TUNING/SEEK/UP/DOWN OR NEXT/BACK BUTTONS
12A. LEFT/RIGHT BUTTONS
12B. UP/DOWN BUTTONS
13. STOP BUTTON
14. OK BUTTON
15. SET UP BUTTON
16. SLOW BUTTON
17. DISC MENU BUTTON
18. GOTO BUTTON
19. L/R AUDIO BUTTON
20. SUBTITLE BUTTON
21. OSD BUTTON
22. PBC /TITLE BUTTON
23. ZOOM BUTTON
24. ANGLE BUTTON
25. PROGRAM BUTTON
7
9
10
1
2
15 17
5
6
3
4
11
8
12A
14
13
12B
16
18
19
20
21
22
23
24
25

6. BASIC OPERATION
E - 9
POWER BUTTON
Press power button to turn on/off the unit.
DISPLAY BUTTON(DISP)
Press this button to remove the control panel.
PANEL RELEASE BUTTON
Press this button briefly,the LCD will display the clock for about 5 seconds, then return to
previous display mode.
Clock Adjustment
Under clock display mode,press DISP button until the LCD flashes,USE VOLUME UP/DOWN to
Adjust hour & minute,press sel button to change the hour & minute.
MUTE BUTTON ( MUTE)
Press MUTE button to mute the sound quickly. the display is flashing Press it again to restore the
previous sound level. When mute is on, the Mute indicator on the LCD will light up.
LOUDNESS BUTTON (LOUD)
Long press this LOUD button control to increase bass output.
MODE BUTTON
Press this button to select radio, DISC/TV(OPTIONAL)/USB/SD/MMC/A/V-IN FRONT/A/V-IN Rear.
(MODE)
SELECT BUTTON (SEL)
press SEL button for less than 1 second to open the Audio menu.
press SEL repeatedly to navigate through the following functions:
VOLUME (VOL) -> BASS (BAS) -> TREBLE (TRE) -> BALANCE (BAL) -> FADER (FAD)->SUB-
WOOFER(SUB-W)(OPTIONEL)
Press Volume Up/Down to adjust desired level within 5 seconds.
NOTE: BASS AND TREBLE WILL BE SKIPPED IF DSP MODE IS ACTIVATED
ENCODER VOLUME KNOB
Turn this knob to adiust desired volumelevel.
PRESET EQUALIZER BUTTON (DSP)
Press this PEQ button then use V-UP / V-DN to toggle the following EQ settings.
POP -> ROCK -> CLASSIC -> DSP OFF
At DSP off mode preset equalizer will be controlled by Bass / Treble setting.
The unit is allowed to connect the with external Audio /
Video system such like Digital Camera or Game Console.
You can connect the external A/V system thru the A/V in
jack on front panel. After connect with external A/V
system, pressing mode to “A/V IN FRONT” to enjoy this
external A/V system on this unit.
FRONT PANEL A/V IN JACK
NOTE: The unit is only support the 3.5mm A/V Jack Pin Assignment shown as the diagram delete
extra "."
3.5mm A/V Cable ( not included )
Video
Right Audio
Left Audio
Ground
1
2
3
4

E - 10
7. RADIO OPERATION
Use this control to select stereo or mono reception for FM radio stations. You can sometimes improve
reception of distant stations by selecting mono mode.
FM MONO / STEREO BUTTON (MONO)
LOCAL / DX BUTTON (LOC)
This control can be used to change between Local and Distant (-DX) tuning mode. Local mode
improves reception in some areas where the signal is too strong.
STATION PRESET BUTTONS (M1-M6)
You can store & recall six preset radio stations by pressing M1-M6 buttons
TO STORE A STATION: 1) select a band (if needed)
2) select a station by tuning up / down button
3) hold a preset button which you want store the station for at least 2
seconds. The preset number will appear on the display accompanied by
a beeps sound.
TO RECALL A STATION: 1) select a band (if needed)
2) press a preset button briefly to recall the stored station.
SCAN BUTTON (SCAN)
Press this button, the radio will tune up to search stations, the available stations will blinking and stay
on the display for a few seconds.
AUTO MEMORY STORE / PRESET SCAN BUTTON (AMS)
PRESET SCAN: press AMS button for less than 1 second to scan all preset stations in the memories
of the current band and stay on each memory stations for about 5 seconds. The
memory location indicator on the LCD will flash during the process. To stop preset
scan, press AMS button again.
AUTO MEMORY STORE: press AMS button for more than 1 second to enter auto store mode. The
radio will automatically store 6 stations to the 6 preset memories of the current band. To stop auto
store, press AMS button again.
BAND BUTTON (BAND)
Press this button to change between band FM1, FM2, FM3 or MW(AM)1, MW(AM)2 bands .
TUNING UP / DOWN BUTTON ( )
Press this button to search for radio stations. Depends on whether SEEK1 or SEEK 2 mode is
selected, different operations can be performed, refer to “SEEK MODE” paragraph for detail.
DUAL FREQUENCY SWITH
Unit is defaulted in U.S.A. Frequency, if EURO frequency is required, a sharp pen is needed to switch
the button on the left side of the chassis to EURO frequency.

8. CD/MULTI-MEDIA FILE
Press this button to select Intro Scan function, the first 10 seconds of each track will be played
sequentially until this button is pressed again, then normal play will resume at the current track.
INTRO SCAN BUTTON (CD SCAN)
Press this button briefly to pause disc play, press again to resume play.
PLAY/PAUSE BUTTON ( )
RANDOM PLAY BUTTON(RDM)
When random play mode is selected, the tracks will be played in random order, press this key one
more time to cancel random play mode.
REPEAT BUTTON(RPT)
Pressing this button will activate Repeat Function in the following order :
Repeat On Repeat Off
The RPT indicator will turn on.
Long press the & buttons under the play mode, the unit will start to forward or rewind. you
can play discs at various speeds. with each consecutive long press the & buttons , the
playback speed increases. there are 5 speed levels for discs in FWD/REV: X2, X4, X8, X16,X20.
there are 4 speed levels for disc types other than disc: X2, X4, X8,X16.
Press PLAY to resume the playback at normal speed.
NEXT/BACK BUTTONS( & )
When NEXT is pressed, the unit will go to the next track and start the playback.
When BACK is pressed, the unit will go back to the previous track and start the playback.
E - 11
NOTE: This will only operate with the SCAN function play on CD.
LOADING THE CD
Press the Panel Open Button to fold down the front panel, insert the disc through CD slot, the
disc will be automatically loaded and playback will also start.
CD EJECT BUTTON
Press this button to eject the CD. Since this button is located behind the front panel, fold down
the panel before accessing this button.
RESET

MULTI-MEDIA FILE OR FOLDER SEARCHING
Selecting a Track to Play
1. Use the UP/DOWN/LEFT/RIGHT direction buttons to move to different file/folder
Numbers.
2. Press OK on a file number, and that file will begin to play, or by direct numeric input,
3. Enter a file number with the numeric buttons (0-9) and +10 button to play the input Files
Number.
E - 12
REPEAT A- REPEAT A- B REPEAT A-B CANCEL
REPEAT A-B BUTTON (A-B)
1. Press REPEAT A-B at your chosen starting point.
2. Press REPEAT A-B again at your chosen end point.
The section A and B can be set only within the same track.
The section will now repeat continuously.
3. To exit the sequence, press REPEAT A-B.
The screen willdisplay the followingmessage:
NOTE:This operate is with CD function only.
Stop the current disc playback.
Press STOP two times consecutively to enter the clear stop mode. Under the clear stop mode, if
PLAY is pressed, the disc will resume the playback from the beginning of the disc.
Briefly press the STOP button to stop the unit playback, when the PLAY
button is pressed, normal playback will continue.
STOP BUTTON( )
NUMERIC BUTTONS
When playback CD/MUSICuse for tracknumber or Filenumber direct accessand
Use when functionneed numeric Selectionor Input, likein the Gotofunction, etc.
UP/DOWN/LEFT/RIGHT BUTTON ( / / / )
Use to movecursor up/down/left/right.
OK BUTTON
Use this buttonto confirm theselection.
GO TO BUTTON (GO TO)
Using GO TOfeature to selecttrack number orspecific time.
A. Press GO TO button,the screen will display the following message:
B. Press ArrowLeft/Right buttons tohighlight the tracknumber or thetime option.
C. Use numericbuttons to enterthe track youwant to playor the elapsedtime you wantto
go to inthat track.
D. Press OK button to start playback. Forexample, entering 00:01:56will start playbackone
minutes and fifty-sixseconds into thetitle.
TRK 001/021
A
00:01:56

PROGRAM BUTTON (PROG)
A. For example:Pressnumeric button 2,PROGRAM 0002 appearsit means track2 will be
player first thenpress numeric button 4 and PROGRAM 0004 appears,press thedifferent
numeric button toselect the corresponding track and thenyou can programtracks to your
need if youwant to complete program setting press PLAY buttonto play tracksin
programmed order.
B.Press the ( / / / )buttons to highlight select program modeor track numberand
press PLAYbutton to confirm it.
C.If you exitprogram mode and program off appears press STOP buttonthen press PLAY
button.
ID3 INFORMATION DISPLAY
If any MUSIC file any ID3-TAG information, user can view these ID3-TAG information such
as Track title, Artist title, Album title, etc, These ID3-TAG information will be displayed on the lower
left hand corner of the TFT monitor.
contains
Press PROG buttonthe screen willdisplay the followingmessage.
PROG
PLAY
1 0002
3 ----
5 ---- 9 ---- 13 ----
6 ---- 10 ---- 14 ----
7 ---- 11 ---- 15 ----
4 ---- 8 ---- 12 ---- 16 ----
2 0004
CLEAR
E - 13

9. PLAY MULTI-MEDIA FILES OPERATION
Place a disc into the player, and the player will auto search the directories saved files. After
searching, it will auto go to the first directory saved files (to the disc containing both Music and
photo files; To the disc containing single type of files, it will automatically go to the first directory) and
play the first song in the directory (“01:” is highlighted).The screen displays as the picture below:
Current directory name
Current file name.
The playing file is a Music File.
The playing file is a Photo File.
File Switch Region: Displays the file type of the playing
and the switching.
Use the Arrow ( / / / )buttons to enter the Directory Region and highlight the desired directory, then the
first track under it starts playback; Also you can use the Arrow( / / / ) buttons to enter the File Region and
select the file you want to play.
Press the Left and Right arrow buttons, you can activate Directory Region, File Region and
File Switch Region separately.
The highlight in Directory Region and File Region is shown as the picture above; While it
appears a transparent rectangle in File Switch Region.
You can press the Numeric buttons to select the file you want to play. For example, if you
th th
desire the 15 track in current list, press the “10+” button once, then press “5”, the 15
starts playback.
When a picture , press the Arrow buttons to change the display
angle:
is playing or paused
E - 14
NOTE:
NOTE:

10. MMC/SD CARD & USB DEVICE OPERATIONS
START THE USB DEVICE MODE
1.The USB socket is accessible as indicated in picture
1.(P.1)
2.Plug in the USB drive / device completely as indicated
in picture 2(P.2) and display will show “USB” to indicate
that the USB drive / device is being plugged in correctly
& the download has begun.
3.Does not matter once a USB
drive / device is being plugged into the unit, the unit will
automatically switch to USB mode.
what mode the unit is in,
4.All the USB files playback function is same as normal
disc playback.
1.Always unplugged the USB gently from the unit,
excessive force used will cause permanent & serious
damage to the unit & the USB drive / device.
TO STOP USB PLAYBACK
CAUTION
COMPATIBILITY
Due to the fast changing technology world, this unit may
or may not be compatible to all the USB drive / device
available with all the future technology, especially those
USB drive / device which require to install a driver. Always
choose a compatible USB drive / device which is
compatible with this unit.
Warning: Excessive weight or size USB drive/device
may cause permanent & serious damage to the unit and
may cause access to the buttons on the front panel
impossible. User must use an extension cable (provide
by USB device manufacturer) to connect with USB
socket to prevent any damage cause.
USB SPECIFICATION
* SUPPORT MAX 1G USB FLASH MEMORY
* SUPPORT MAX 999 SONGS
* USB 1.1 DEVICE SUPPORT
* USB 2.0 DEVICE SUPPORT
(TRANSFER SPEED SAME AS VER 1.1)
* FILE MANAGER: FAT12/FAT16/FAT32
E - 15
P. 1
USB SOCKET
P.2
P. 3
1.If the USB drive / device is unplugged, the unit will automatically switch to radio mode.
Or the user can use the mode button to switch to other modes.
2.The user can use the mode button to choose USB mode (only if USB drive / device is
inserted in the unit ) or any other modes, when they are in any mode.

START THE SD/MMC MODE
E - 16
CAUTION
2.Please make sure to insert the SD or MMC
card in the correct direction as
indicated in picture 7(P.7). Wrong insert will
cause permanent & serious damage to the
unit & the SD or MMC card.
and position
TO STOP SD/MMC CARD PLAYBACK
1.Push on the end of the SD or MMC card to eject the SD or MMC card. Once the SD or MMC
card is taken out, the unit will automatically switch to previous mode.
2.User can use the mode button to choose SD / MMC mode (only if SD or MMC is inserted in
the unit ) or any other modes, when they are in any mode.
SD/MMC SPECIFICATION
* SUPPORT MAX 4G SD/MMC CARD
* SUPPORT MAX 999 SONGS
Back side
Front side
P. 7
3.The SD/MMC card slot is located on top of the front panel as
indicated in (P.6).
4. Insert the SD/MMC card into the card slot in the correct direction
until a “CLICK” sound is heard.
5.Close the front panel.
6. The display will show “CARD” to indicate that the SD or
MMC card is correctly inserted. Once the SD or MMC card is
inserted, the file will automatically loaded & playback will also
start.
7. Does not matter once the SD or MMC
card is being inserted in the unit, unit will automatically switch to SD
/ MMC mode.
what mode the unit is in,
8. All the SD / MMC files playback function is same as normal CD or
disc playback.Multi-Media
1. Press the panel open button,the D.C.P will drop down.
2. Push the D.C.P in the left direction until the point D
at the right side of D.C.P
(As shown on the diagram).
disconnects from the DCP
P. 6
P. 4
P. 5
D.C.P.
D

Press this button briefly to pause disc play, press again to resume play.
PLAY BUTTON ( )
Stop the current disc playback.
Press STOP two times consecutively to enter the clear stop mode. Under the clear stop mode, if
PLAY is pressed, the disc will resume the playback from the beginning of the disc.
Briefly press the STOP button to stop the unit playback,when the PLAY button is pressed,normal playback
will continue.
STOP BUTTON( )
UP/DOWN/LEFT/RIGHT BUTTON ( / / / )
Use to movecursor up/down/left/right.
OK BUTTON
Use this buttonto confirm theselection.
Long press the & buttons under the play mode, the unit will start to forward or rewind. you can
play discs at various speeds. with each consecutive long press the of & buttons , the
playback speed increases. there are 5 speed levels for discs in FWD/REV: X2, X4, X8, X16,X20. there
are 4 speed levels for disc types other than disc: X2, X4, X8,X16.
Press PLAY to resume the playback at normal speed.
NEXT/BACK BUTTONS( & )
When NEXT is pressed, the unit will go to the next track and start the playback.
When BACK is pressed, the unit will go back to the previous track and start the playback.
NUMERIC BUTTONS
Use when playbackDisc which neednumeric Selection orInput, like inthe
Goto function,etc
11. OPERATIONSVIDEO DISC
In order to achieve the best image display effect, you must adjust the player signal system to
match your TV set.
PAL/NTSC BUTTON (P/N)
3 types of TV color signal system are available: NTSC, PAL60 or Automatic mode.
Use P/N button to select between NTSC/PAL, or automatic mode.
REPEAT A- REPEAT A-B REPEAT A-B CANCEL
REPEAT A-B BUTTON (A-B)
1. Press REPEAT A-B at your chosen starting point.
2. Press REPEAT A-B again at your chosen end point.
The section A and B can be set only within the same track/chapter.
The section will now repeat continuously.
3. To exit the sequence, press REPEAT A-B.
The screen willdisplay the followingmessage:
L/R BUTTON(L/R)
Press R/L button for select leftand right channel.
The screen willdisplay the following message:
STEREO MONO L MONO R
E - 17

ZOOM BUTTON(ZOOM)
The ZOOM featureallows you tomagnify a certainarea of theimages recorded onthe
and other imagediscs. the screenwill display thefollowing message:
Video
disc
SLOW BUTTON (SLOW)
A. Press “SLOW”button once to activate SLOW 1/2 slow motionplayback.
B. Press “SLOW” button twiceto activate SLOW 1/3 slow motion playback.
C. Press “SLOW” button threetimes to activate SLOW 1/4 slow motion playback.
D. Press “SLOW” button four times to activate SLOW 1/5 slow motionplayback.
E. Press “SLOW”button five timesto activate SLOW 1/6 slowmotion playback.
F. Press “SLOW” button six times to activateSLOW 1/7 slow motion playback.
G. Press “SLOW” button againto restore normalplayback.
The screen willdisplay the following message:
A. Press ZOOM button to enlarge the image byX2.
B. Press ZOOMbutton twice times to enlarge the image by X3.
C. Press ZOOMbutton again to enlarge the image by X4.
D. Press UP/Down/Left/Right to select the area youwant to magnify.
E. The four times press ofZOOM will cancelthe zoom functionand resume normal playback.
ZOOM X2 ZOOM X3 ZOOM X4 ZOOM OFF
PBC FUNCTION BUTTON (PBC)
Pressing the "PBC" button to turn on PBC function. The unit will show the song list on the
screen of the monitor after the WARNING from the Video CD. Then you can choose the song
by pressing the desired number key.
Press PBC key return to manual of Video CD.
NOTE:This only operates with the PBC function on VCD.
GO TO BUTTON (GO TO)
Using GO TOfeature to selecttrack number orspecific time:
SF1/2SF1/3SF1/4SF1/5SF1/6SF1/7PLAY
A. Press GO TO button,the screen will display the following message:
B. Press ArrowLeft/Right buttons tohighlight the track/title/chapternumber or thetime
Option.
C. Use numericbuttons to enter the track/title/chapter you want to play or the elapsed time
you want togo to in that track/title/chapter.
D. Press OK button to start playback.For exampleentering 01:11:56 will start playback one
hour,eleven minutes and fifty-sixseconds into thetitle.
TT 01/05 CH 011/018 01:11:56
E - 18