Sound Storm S10.4FI User manual

Specifications
10
DC 12V
9W
10.4 TFT-LCD
4:3 Wide
1152*234
Video Input 2EA
(L)12.1 (W)11.5 (H)1.6inch
DC 12V
3W
Right 2.8MHz Left 2.3MHz
Active Matrix TFT-LCD
Power Requirements
Power Consumption
Screen Size
Screen Format
Resolution Pixel
A/V Inputs
Dimensions
IR Power Requirements
IR Power Consumption
IR Transmitter Frequency
LCD Panel Type
Compatible video standard
NTSC/PAL Auto Select

Contents
2
9
Troubleshooting
Precautions 3
Monitor Operations 4
Monitor Features and Controls 6
Remote Control Features 7
Installation 8
Troubleshooting 9
Specifications 10
Please make these simple checks before calling for assistance.
If this product is to be used in a system with any other equipment,
read the other product,s instruction manual.
Never attempt to repair a defective monitor yourself. Check with
your dealer. If you are not able to resolve the problem by checking
the items below.
Make sure that:
Power cord is properly inserted.
Signal or power cord of connected components is not properly
inserted.
AV input signal is present on the video inputs.
Make sure that:
AV input signal is present on the video inputs.
Contrast and brightness settings are properly adjusted.
Make sure that:
Batteries have sufficient power, and replace if necessary.
Batteries are properly installed, with polarity correctly observed.
The distance between the remote control and the IR window on
the monitor is within 6 feet and the angle is no greater than 30
from the front of the window.
Problem: No picture and no sound
Problem: No picture
Problem:Monitor does not respond to remote control.

3
Precautions
8
Installation
1 Using self-tapping screws to attach mounting plate to
the selected position in your vehicle.
2 Install the housing onto the mounting plate the four
screws supplied.
Do not install this product so that the screen can be seen by
the driver.
Do not install this product so that any part of the product blocks
the driver's view.
Always play the audio at moderate levels.
Never attempt to operate this product while driving.
Do not attempt to repair the unit or to open the housing.
Do not drop or strike the monitor housing or screen.
Do not watch the monitor for long periods when the engine is
off, as this may cause the vehicle battery to discharge.
Do not attempt to recharge the battery in the remote control.
Keep the remote control away from children.
Use on only a soft cloth with non-ammonia glass cleaner to
clean the screen.
1. The installed temperature range for this monitor is
2. The range of temperatures in which the monitor can be USED is smaller, from 32
(0 If this occurs, wait until the temperature enters the correct range and the screen
will return to normal.
3. For best viewing, you should be no more than 45 to the right or left side and at approximately
eye level.
-4 to158F(-20 to70 ).
to 104 F
to 40 ).
(Visual Angle)
20
40
45 45
A mobile video system in a vehicle may distract the
driver, so please observe the following precautions.
Notes on using this monitor

BATTERY 12V
Monitor Operations
4
35
35
2m
Connections
7
Video source
VIDEO 1
VIDEO 2
AUDIO1 R AUDIO1 L
DC 12V GROUND
AUDIO2 R
AUDIO2 L
S-Video Connector
Release the monitor by press the RELEASE button. Adjust the
monitor to a comfortable viewing angle.
RELEASE Button
Infrared Transmitter
Dome Lights
Dome Lights switches
R
MENU
VIDEO
This monitor has a built-in wireless infrared audio transmitter.
When used with headphones (model SHP, not included) it provides
a perfect way for you to enjoy the audio part of a video program
without disturbing other occupants in the car.
Infrared transmission requires line-of-sight for the system, so it is
important to be no more than 35 to the right or left of the monitor,
and no further than 2 meters away for best sound quality.

LCD MONITOR
REMOTE CONTROL UNIT
5
Monitor Features and Controls
6
Remote Control Features
Monitor control functions:
Power: Use this button to turn on or off the monitor.
AV Select: Use this button to select either AV1 or AV2 input.
Menu: Use this button to enter the on-screen menu system.
+ and - buttons: Use these buttons to increase or decrease
values for various items in the on-screen menu system.
Power Button
TFT-LCD Screen
+ Button
AV Select Button
POWER button AV select
+ button
- button
menu
Remote control functions:
Power: Use this button to turn on or off the monitor.
AV Select: Use this button to select either AV1 or AV2 input.
Menu: Use this button to enter the on-screen menu system.
+ and - buttons: Use these buttons to increase or decrease
values for various items in the on-screen menu system.
- Button
Menu Button