Sound Storm SSV7HRB User manual

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors,cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar. Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroudand slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shrouduntil you feel a click.As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroudand out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
a position where it is visible to the
driver, be sure toinstall a Safety Cord.
Wire this cord to an accessory wire
which has +12v power when the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs toa qualified
service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cordand send the monitor to your
local dealeror service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitor controls and features
6 Remote control
6Remote control battery replacement
7System wiring
8Monitor installation
10 Relmoving the monitor
11 Troubleshooting
12 Specifications
Congratulations on yourpurchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thankyou for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
L A B O R A T O R I E S
®
NOTE: Headrests vary in their construction.Most headrests have a plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absentor is too deeply located for attachment. In
this case, youmay wish to cuta plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
Please read this manual completely
and carefully prior to attempting to
install your new Boss mobile video
equipment. Installed correctly, your
Sound Storm equipment will provide
you with years of enjoyable and safe
usage.
Installation of this equipment in any
portion of a vehicle which impairs or
distracts the driver is improper and
dangerous. Sound Storm assumes
no liability whatsoever for failure to
follow the proper installation of this
product.
Please keep this manual in a safe place
for future reference.
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not install this product in a location
which allows the monitor screen tobe
visible to the driver of the vehicle. In
some states and countries, the viewing
of images on a screeen inside a vehicle
is illegal, even by people other than
the driver. Be sure that the installation
and operation of this system is in
compliance with local rules and
regulations.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs toa qualified
service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
SHOCK HAZARD! Do not open the case
of thisproduct.There are dangerous
voltages present within the unit. Thereare
no user-serviceable parts within the unit.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cordand send the monitor to your
local dealeror service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• Do not install this product in a location
which allows the monitor screen to be
visible to the driver of the vehicle. In
some states and countries, the viewing
of images on a screeen inside a vehicle
is illegal,even by people other than
the driver. Be sure that the installation
and operation of this system is in
compliance with local rules and
regulations.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
Operating precautions
Turn the unit off when it is not in use.
Avoid dropping any metal objects or
inflammable items into the monitor
ventilation slots.
Do not place objects on or suspend
objects from the power cord, as this
may damage the cord.
Installation precautions
Choose a mounting location in your
vehicle where the unit will not distract
or otherwise interfere with the driver’s
ability to control the vehicle.
Do not install components in areas
which are susceptible to rain, moisture,
direct sunlight,extreme heat or cold,
excessive dust, dirt or humidity.
If installation requires drilling holes or
othermodifications to the vehicle,
consult with your nearest dealer or
professional car audio installer.
Use only the installation parts and
hardware provided with the unit to
ensure proper installation. Usingother
parts can cause malfunction and
possible damage to your Sound Storm
video monitor.
Use only a power source with 12Volts
DC (negative ground).
Before final installation, temporarily
connect the wiring according to the
diagram near the end of this manual,
check it to ensure that it has been
connected properly, and test the unit
to make sure it is working correctly.
Afterthe monitor is installed, do not
arbitrarily pull it down or strike it. This
may loosen the mounting screws and
cause it to fall down.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
Your new video monitor features the
following:
• TFT Active Matrix LCD display
• On-screen menu system
• Dual AV inputs
• Wireless remote control
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCDmonitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitorremoval key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions (L x W x H)
All specifications subject to change without notice.
MODEL
REMOTE IR SENSOR
3
MENU
This buttonenables the on-screen
display menu system. Once enabled,
this buttonis used as an ENTER
button.
4
SYMPTOM CAUSE REMEDY
1POWER ON/OFF
This button turns the monitor system
on and off.
2A/V SOURCE SELECTOR
Use this buttonto switch between
A/V Source 1 and A/V Source 2.UP/DOWN BUTTONS
These buttons are used to increase
or decrease parameters in the on-
screen display menu system.
5
VIDEO
INPUT 1
1
power A/V source menu
+
SSV7HRB
2 4 53
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
Release button
Battery
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCDmonitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitorremoval key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
Theremote battery is held in a small
“drawer” on one edge of the remote. To
open this drawer, press and hold the small
button on the edge of this drawer (as shown
below) and slide the drawer out.
Insert a new battery and push the drawer
back fully into the remote.
Changing the battery in the remote control
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions (L x W x H)
All specifications subject to change without notice.
MODEL
POWER
Press to turn unit ON or OFF.
1
AV1/AV2 (AV SOURCE SELECT)
Use this buttonto switch between
A/V Source 1 and A/V Source 2.
2
MENU
This buttonenables the on-screen
display menu system. Once enabled,
this button is used as an ENTER button.
3
INCREASE/DECREASE BUTTONS
These buttons are used to increase
or decrease parameters in the on-
screen display menu system.
4
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
1 2
3
4
LCD MONI TOR
REM OT E CONTROL UNIT
POW ER AV1/AV2
MENU
L A B O R A T O R I E S
®
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
System wiring
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCDmonitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitorremoval key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions (L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
POWER
RED
BLACK
FUSE
to Chassis Ground
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
12V
Battery
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to be cut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
othercorners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors,cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar. Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroudand slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shrouduntil you feel a click.As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroudand out below the headrest.
Carefully peel back the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
a position where it is visible to the
driver, be sure toinstall a Safety Cord.
Wire this cord to an accessory wire
which has +12v power when the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs toa qualified
service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cordand send the monitor to your
local dealeror service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
Monitor installation
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitor controls and features
6 Remote control
6Remote control battery replacement
7System wiring
8Monitor installation
10 Relmoving the monitor
11 Troubleshooting
12 Specifications
Congratulations on yourpurchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thankyou for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
If you have any doubts about this type of installation, please consult your local mobile
electronics retailer. Making holes in the upholstery of your vehicle can cause damage
which is expensive to repair.
CAUTION
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
1/4"
1/4"
1/4"
1/4"
NOTE: Headrests vary in their construction.Most headrests have a plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absentor is too deeply located for attachment. In
this case, youmay wish to cuta plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors,cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar. Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroudand slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shrouduntil you feel a click.As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroudand out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
•Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
a position where it is visible to the
driver, be sure toinstall a Safety Cord.
Wire this cord to an accessory wire
which has +12v power when the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs toa qualified
service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cordand send the monitor to your
local dealeror service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitor controls and features
6 Remote control
6Remote control battery replacement
7System wiring
8Monitor installation
10 Relmoving the monitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
1"
3/4 - 1"
NOTE: Headrests vary in their construction.Most headrests have a plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absentor is too deeply located for attachment. In
this case, youmay wish to cuta plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure toinstall a Safety Cord.
Wire this cord to an accessory wire
which has +12v power when the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
•Do not open orattempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs toa qualified
service technician.
•Do notattempt to repair a damaged,
broken or faulty power cord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, do not permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cordand send the monitor to your
local dealeror service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the component enclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
Should you need to remove the monitor from the shroud, insert the removal key
as shown in the diagram below.
Insert the two prongs of the key into the gap between the monitor and the shroud
(as shown in the diagram) to depress the two snap catches on the side of the
monitor which secure it. Then use the key to gently lift the right side of the monitor
out of the shroudand remove it.
Be sure to push the monitor all the way back in until you feel a clickwhen you are
reassembling the monitor system.
Removing the monitor
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.
power A/V s ource menu
+
SSV7HRB

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiringdiagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
No picture or
sound.
Power cord is not
properly connected.
A/V input cables not
properly connected.
A/V input source is not
operating properly.
Check that power connections
are properly made and all fuses
are in functioning condition.
Check all cables.
Replace or repair A/V source
(DVD player, video game, etc.)
No picture. A/V signal not present.
Contrast and/or
brightness is set
improperly.
TV reception is poor
(applies to system with TV
tuner only)
Check all cables. If necessary,
repair or replace A/V source.
Adjust contrast and brightness
levels to see if picture appears.
Check and adjust antenna
system. Move to another area
with better reception, if
possible.
Remote control
does not function
properly.
Batteries are dead.
Remote is not being used
in direct line-of-sight with
the player or remote IR
sensor. Transmission is
best within 6 feet/30º
angle of IR sensor on
monitorfront panel, and
within .
Replace batteries.
Be sure when being used, the
remote is being pointed directly
toward the player or remote IR
sensor (if installed).
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.

On a towel or soft cloth, gently place the monitorassembly “face down” ona stable
worksurface.
Using the wires provided, complete the audio, video and power connections in
your vehicle as shown in the diagram below.
Carefully remove the headrest and set it down
in an uncluttered work are. Take the appropriate
precautions to ensure it is not damaged during
installation.
Push on the headrest with your fingers to make
sure there are no obstructions inside that would
interfere with the installation. After you confirm
that there are no internal obstructions, take the
paper template provide in place, and mark the
area to becut.
Using a sharp, adjustable-depth blade knife,
make a diagonal cut beginning 1/4" INSIDE
from one corner, and ending 1/4" INSIDE from
the opposite corner.
Repeat, cutting diagonally between the two
other corners.
Set the adjustable blade to 1" depth, and cut
around the edges of the hole, staying 1/4"
inside the edge. Pull up one corner of the foam
rectangle, and use the blade to cut underneath
– remove a small section at a time, using the
"pull up and cut" method for uniform depth.
If necessary, use a Dremel tool or other appro-
priate tool to remove any other obstructions
present.
Using a sharp scissors, cut the points offf the
flaps of upholstery material to about 3/4" - 1"
wide.
Route the cable through the opening just cut,
and out the bottom of the headrest. If possible,
conceal the cable using a gear shift covering
or similar.Then fold the four flaps into the
cavity in the headrest.
Slide the trim frame onto the monitor
shroud and slide the assembly into the
cavity in the headrest. As you do this,
feed the cable through the headrest as
shown in the diagram. Secure the shroud
with the three screws as shown.
Connect the RCA cables and the power
cable, and slide the monitor into the
shroud until you feel a click. As you do
so, push the cables into the headrest
shround so they travel into the area behind
the shroud and out below the headrest.
Carefully peelback the upholstery material.
VIDEO SOURCE 1
(DVD player, video game, etc.)
VIDEO SOURCE 2
(DVD player, video game, etc.)
CONTENTS
SSV7HRB User’s Manual - Contents
U S E R ’ S M A N U A L
SSV7HRB User’s Manual - page 7
SSV7HRB User’s Manual - page 10
SSV7HRB User’s Manual User’s Manual - page 2
General precautions
Safety precautions
SSV7HRB User’s Manual User’s Manual - page 3
SSV7HRB User’s Manual - page 4
Features What is included? Monitor Controls and Features
SSV7HRB User’s Manual - page 5
SSV7HRB User’s Manual- page 6
Troubleshooting
SSV7HRB User’s Manual - page 11
Specifications
SSV7HRB User’s Manual - page 12
Remote Control
SSV7HRB User’s Manual - page 8 SSV7HRB User’s Manual - page 9
• Do not operate this equipment while
driving – safe driving should always
be your highest priority.
• This product should not be installed
in a location which allows the monitor
screen to be visible to the driver of the
vehicle. In some states and countries,
the viewing of images on a screeen
inside a vehicle is illegal, even by
people other than the driver. Be sure
that the installation and operation of
this system is in compliance with local
rules and regulations.
• If you have installed the monitor in
aposition where it is visible to the
driver, be sure to install a Safety Cord.
Wire this cord to an accessory wire
which has +12v powerwhen the
ignition is switched on. This will prevent
the operaton of the monitor when the
engine is running.
• Do not open or attempt to repair this
unit yourself. Dangerous high voltages
are present which may result in electric
shock. Refer any repairs to a qualified
service technician.
• Do not attempt to repair a damaged,
broken or faulty powercord. Replace
it with a new one immediately.
• To avoid risk of electronic shock or
damage to the monitor, donot permit
any of this equipment to become damp
or wet from water or drinks. If this does
occur, immediately unplug the power
cord and send the monitor to your
local dealer or service center as soon
as possible.
• if there is smoke or any peculiar odor
present during useor if there is damage
to any of the componentenclosures,
immediately unplug the power cord
and send the monitor to your local
dealer or service center as soon as
possible .
If you do not know how to install the
Safety Cord, please consult with a
mobile video installer in your area, and
have this work completed properly
before operating the video system.
When first unpacking your new flip-
down monitor, please check first that
the package contains all of the items
below. If something is missing, contact
the store where you purchased the
player.
• LCD monitor
• Mounting shroud
• Trim bezel
• Wireless remote control with
batteries
• RCA-RCA video cable
• Video/power interface cable
with inline fuse
• Monitor removal key
• Mounting screws
If you experience operation or performance problems with this product, compare your
installation with the electrical wiring diagram on the previous page. If problems persist,
read the following troubleshooting tips which may help eliminate the problems.
2General precautions
2Safety precautions
3Installation precautions
3Operation precautions
4Features
4What is included?
5Monitorcontrols and features
6 Remote control
6Remote control battery replacement
7Systemwiring
8Monitor installation
10 Relmoving themonitor
11 Troubleshooting
12 Specifications
Congratulations on your purchase
of a Sound Storm Video Monitor.
It has been designed, engineered and
manufactured to bring you the highest
level of performance and quality, and
will afford you years of viewing
pleasure.
Thank you for making Sound Storm
your choice in car video entertainment!
page
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
A/V SYSTEM
Screen size
Screen format
Video Compatability
LCD panel type
Resolution, pixels
Brightness
GENERAL
Power requirements
Power consumption
Dimensions(L x W x H)
7"
16:9 (wide)
NTSC
Active Matrix TFT
1440 x 234
450 NITS
12-14V DC
6W
7.8"x 5.5" x 1.0"
SSV7HRB
7" Headrest Widescreen
TFT Video Monitor
All specifications subject to change without notice.
MODEL
SYMPTOM CAUSE REMEDY
VIDEO
INPUT 1
VIDEO
INPUT 2
Insert the removal key into the gap
on the right side of the monitor to
depress the tabs to release it.
L A B O R A T O R I E S
®
NOTE: Headrests vary in their construction. Most headrests havea plastic
plate inside into which you can directly attach the mounting screws. However,
in some cases this plate is absent or is too deeply located for attachment. In
this case, you may wish to cut a plate of wood of appropriate thickness and
hot-glue it into place to use as a mounting plate.