Sound Tube RSi Series Configuration guide

SOUNDTUBE
Lead.
Or
follow
.
•
Rs
•
S • IInstall Instructions For:
I
erleS
RS4-EZ, RS400i, RS500i,
HP590i,
RS
600i,
HP690i,
RS800i,
HP890i,
RSlOOli-11, HP
12
9i
&
HP1290
i
s
pe
a
kers
Secure
anchorpoint
II
l I
Hangingorsafetycable
~
Speed
Clamp
·
·--__,~
Safetycable withclip
---~
'tl----
Hangingcablewithclip
Signalwire \
Terminalweather
boot---~
Euroblockconnector
~
Euroblockjack /
M
If
R:~'
Surface:mount
II
~
bracketmsert
RS400i, RS500i, RS600i, RS800i, RSlOOli·ll, HP690i, HP890i, HP129i, and HP1290i . UL listed
1480
m
Sound
Tub
e sp
ea
kers must be 1r sta
ll
ed
by
a
prof
es
s1ona
l aud•o
li1
Stall
eu
co
ntr
actor For
sa
fety and f
or
opt
rrnum aud;o perf
or
mance. rnsta
ll
er
mu
st follow all d rr
ec
tr
on
s r
ss
ued by S
ou
nd
Tu
be E
nt
e
rt
ar
nm
ent.
Box contents
1 Speaker
2 SpeedCiamps
'"
1 Release key (small hex wrench)
1 Hanging cable
1 Safety cable
1 Terminal weather boot
1 Euroblock connector
1 Grille-mounted tap
swit
ch
co
ver
4 Zip ties
RS4-EZ&
RS400i
tap
location
Euroblockjack
1.435.647.9555
I
800.647.
TUBE I www.soundtube.com
©2009
So
undTube
En
terta
inment, Inc.
All
rights
reserved
.
PN
IN
S-
RSI
Rev
0
5.
13.09
m
Do not spec or
•n
sta
ll
speaker near sup
po
rt
beam. ven!lla
t1
on duct or
o
th
er structure
th
at may r
nt
e
rf
ere
\V
rt
h speak
er
fun
cti
on
or
drspersro:
"'l

Install Instructions For:
RSi Series RS4-EZ, RS400i, RS500i,
HP590i, RS600i, HP690i, RS800i, HP890i, RSlOOli-11, HP129i & HP1290i speakers
1. Unpack speaker and
SpeedCiamp'"' mounting
hardware.
2. Selectthe tap position by 3. Slip terminal weather
removingthe rubberplug
on boot over signal wire. For
grilietoaccess rotaryswitch.
en vironmentaI applications,
Switch ispresettomaximum
put RTV silicone around
tapsettingin
70.7Vmode. nipple and base when
Selectdesired settingand installation is complete.
reinsertrubberplug.
Note: The
grille-mounted
tap switch
coveriskeyed; besure
flat
edgeofplug lines up with flat
edgeofhole in grille.
5. Thread hanging or safety 6. Attach the hanging cable
cable through SpeedCiamp
TM by securing it and safety 7. Thread cable end(s)
through SpeedCiamp'
"'
mechanisms as shown.mechanisms as shown. cable to structure as shown.
9. Attach hanging cable to
the center hole in the
speaker hanging bracket.
10. Attach the safety cable to
one of the secondary holes
in
the hanging bracket.
11. Insert 4-pin Euroblock
plug into Euroblock jack on
rear
of speaker. Connectors
are keyed for polarity.
4. Connect signal wire to
4-pin Euroblock plug. Tighten
unused terminal screws.
Use
inside positive and negative
inputs for either voice coil or
distributed systems.
For daisy
chaining,
use outside positive
and negative terminals.
8. Adjust speaker hanging
height
with SpeedCiamp '"'
mechanism. Pull to tighten &
insert release
key (small hex
wrench) into SpeedCiamp '"'
as shown to loosen or adjust.
12. Use zip or twist-lock ties
to secure safety cable & signal
wire
to main hanging cables.
Cable cover available for
asthetic applications
(SL T-10).
SoundTube also provides optional surface mount brackets for both the RS and HP lines of products.
Installation instructions for these accessories are included with specific accessory packaging.