Southern Enterprises FA968800TX User manual

For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
FA968800TX
Manchester Fireplace Console -
Brown Mahogany
Assembly Instructions
PO#:
Page1

Manchester Fireplace Console
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
.
1.
Quantity
of 1
Top Panel
2.
Quantity
of 1
Left Upper Side Panel
3.
Quantity
of 1
Upper Middle Panel
4.
Quantity
of 1
Right Upper Side Panel
5.
Quantity
of 1
Fixed Shelf Panel
6.
Quantity
of 1
Lower Left Side Frame
7.
Quantity
of 1
Lower Right Side Frame
8.
Quantity
of 1
Lower Middle Panel
9.
Quantity
of 2
Vertical Panel
10.
Quantity
of 2
Cross Panel
11.
Quantity
of 1
Adjustable Shelf Panel
12.
Quantity
of 1
Door
Page 2

13.
Quantity
of 1
Bottom Panel
14.
Quantity
of 2
Su
pport
Rail
15.
Quantity
of 1
Center Leg
16.
Quantity
of 2
Wood Block
17.
Quantity
of 1
Large Drawer Front
18.
Quantity
of 2
Left Drawer Side Panel
19.
Quantity
of 2
Right Drawer Side Panel
20.
Quantity
of 1
Large Drawer Back
21.
Quantity
of 1
Large
Drawer Bottom Panel
22.
Quantity
of 1
Drawer Bottom Rail
23.
Quantity
of 1
Small Drawer Front
24.
Quantity
of 1
Small Drawer Back
25.
Quantity
of 1
Small Drawer Bottom Panel
26.
Quantity
of 1
Left Upper Back Panel
27.
Quantity
of 1
Right Upper Back Panel
Page 3

28.
Quantity
of 1
Lower Back Panel
A.
Qua
ntity
of 32
Wood Dowel Dia 8 x 30mm
B.
Quantity
of 34
Cam Bolt
C.
Quantity
of 34
Cam Lock
D.
Quantity
of 16
S
crew
Dia1/8
”
x1
”
L
E.
Quantity
of 4
Ball Bearing Slide
F.
Quantity
of 24
Screw Dia1/8”x1/2”L
(For Ball bearing slide)
G.
Quantity
of 1
Magnet
H.
Quantity
of 1
Magnet Plate
I.
Quantity
of 2
Screw Dia1/8”x5/8”L
(For Magnet )
J.
Quantity
of 4
Shelf Pin
K.
Quantity
of 2
Hinge
L.
Quantity
of 15
Screw Dia1/8”x3/4”L
Page 4

M.
Quantity
of 2
Drawer Handle
N.
Quantity
of 1
Door Handle
O.
Quantity
of 6
Bolt Dia 5/32”x5/8”L
P.
Quantity
of 30
Screw Dia1/8”x1/2”L
(For back panel)
Q.
Quantity
of 1
Firebox (in separate carton)
R.
Quantity
of 8
Screw Dia1/8”x1-1/4”L
S.
Quantity
of 4
Bracket
T.
Quantity
of 2
Plastic Strap
U.
Quantity
of 4
Anchor
V.
Quantity
of 4
Screw Dia1/8”x5/8”L
W.
Quantity
of 4
Screw Dia1/8”x1-3/8”L
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)
Page 5

Figure 1
Use screws (D) and wood dowels (A) to
attach cross panel (10) to vertical panel
(9).
Tighten screws (R) with Phillips
screwdriver.
Figure 2
Insert cam locks (C) into holes on
assembled unit.
Screw cam bolts (B) into holes on lower
middle panel (8).
Attach assembled unit to lower middle
panel (8) by inserting wood dowels (A)
and cam bolts (B) into corresponding
holes until lower middle panel (8) and
assembled unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Page 6
Manchester Fireplace Console
Assembly Instructions

Figure 3
Use screws (R) and wood dowels (A) to
connect support rails (14) to bottom
panel (13).
Tighten screws (R) with Phillips
screwdriver.
Figure 4
Insert cam locks (C) into holes on
assembled unit.
Screw cam bolts (B) into holes on
bottom panel (13).
Attach assembled unit to bottom panel
(13) by inserting wood dowels (A) and
cam bolts (B) into corresponding holes
until bottom panel (13) and assembled
unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Page 7

Figure 5
Insert cam locks (C) into holes on the
bottom of assembled unit.
Screw cam bolts (B) into holes on lower
left side frame (6) and lower right side
frame (7). Attach lower left side frame
(6) and lower right side frame(7) to
assembled unit by inserting wood
dowels (A) and cam bolts (B) into
corresponding holes until assembled
unit, lower left side frame (6), and lower
right side frame (7) meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 6
Insert cam locks (C) into holes on
assembled unit.
Screw cam bolts (B) into holes on
underside of fixed shelf panel (5).
Attach fixed shelf panel (5) to assembled
unit by inserting wood dowels (A) and
cam bolts (B) into corresponding holes
until fixed shelf panel (5) and assembled
unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Page 8

Figure 7
Attach center leg (17) to assembled unit
by hand.
Figure 8
Disassemble metal slides into male slide
and female slide as shown.
Note: There is a lever located on the
male slide. Push the lever to the
either side in order to detach the male
slide from the female slide.
Page 9

Figure 9
Attach female ball bearing slides (E) to
left upper side panel (2) with
wood screws (F). Make sure the front of
the slide is facing towards the front as
shown.
Tighten screws (F) with Phillips
screwdriver.
Note: When attaching the female
slides, make sure to insert wood
screws through the first opening
starting from the front, then align the
openings to the pre-drilled holes on
the panels.
Repeat with upper middle panel (3) and
right upper side panel (4) as shown.
Figure 10
Insert cam locks (C) into holes on left
upper side panel (2), upper middle panel
(3), and right upper side panel (4).
Screw cam bolts (B) into holes on
assembled unit.
Attach left upper side panel (2), upper
middle panel (3), and right upper side
panel (4) to assembled unit by inserting
wood dowels (A) and cam bolts (B) into
corresponding holes until left upper side
panel (2), upper middle panel (3), right
upper side panel (4), and assembled
unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Page 10

Figure 11
Insert cam locks (C) into holes
on assembled unit.
Screw cam bolts (B) into holes on top
panel (1).Attach top panel (1) to
assembled unit by inserting wood
dowels (A) and cam bolts (B) into
corresponding holes until top panel (1)
and assembled unit meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 12
Attach the left upper back panel (26),
right upper back panel (27), and lower
back panel (28) on the assembled unit
with screws (P).
Tighten with Phillips screwdriver.
Page 11

Figure 13
Assemble the door (12) onto the
assembled unit using hinges (K) and
screws (L).
Tighten screws (L) with a Phillips
screwdriver.
Attach the magnet (G) on the assembled
unit using screw (I).
Attach the metal plate (H) on the inner
inside of the door frame using screws
(L)
Attach the door handle (N) on the door
using bolt (O).
Figure 14
Insert shelf pins (J) into holes on lower
right side frame and lower midde panel .
Insert shelf (11) in the arrows direction.
Make sure the shelf pin (J) stably holds
the shelf (11).
Page 12

Figure 15
Attach drawer side panels (18), (19),
and drawer back panel (24) and tighten
using screws (D).
Insert drawer bottom panel (25) into the
grooves of panels (18), (19), and (24).
Attach small drawer front panel (23) to
the assembled drawer using screws (D).
Finally attach the drawer handle (M) on
the drawer front using bolts (O).
Figure 16
Attach male metal slide(E) to drawer
sides with wood screws (F). Make sure
the open end of the slide is facing
towards the back of the drawer in order
to attach to the female slide.
Tighten screws with a phillips
screwdriver.
Page 13

Figure 17
Insert cam locks (C) into holes on
drawer bottom rail (22). Screw cam bolts
(B) into holes on large drawer back (20).
Attach large drawer back (20) to drawer
bottom rail (22) by inserting cam bolt (B)
into corresponding hole until large
drawer back (20) and drawer bottom rail
(22) meet.
Tighten by rotating cam lock (C)
clockwise with Phillips screwdriver.
Attach the left drawer side panel (18)
and right drawer side panel (19) to
drawer back (20), make sure the
grooves match and tighten them using
screws (D).
Insert the large drawer bottom (21) into
the corresponding grooves of drawer
back (20), left drawer side (18), and right
drawer side (19).Attach drawer front
panel (17) to the front of the drawer
using screws (D). Attach the drawer
handle (M) on the drawer front using
bolts (O) as shown.
Page 14

Figure 18
Attach male metal slides (E) to drawer
sides with wood screw (F).
Tighten screws with a Phillips
screwdriver.
Figure 19
Insert drawers into assembled unit.
Make sure drawer’s male ball bearing
slides are carefully inserted into side
panel’s female ball bearing slide. Make
sure ball bearing slides glide smoothly in
and out.
Page 15

Figure 20
Carefully insert the firebox (Q) into the
cabinet to avoid scratching.
Figure 21
Use screws (R) to connect wood blocks
(16) to support rails.
Tighten screws (R) with Philips
screwdriver.
Page 16

Figure 22
Attach brackets (S) to back panel using
screws (V).
Tighten screws (V) using Philips
screwdriver.
Mark two desired locations on the wall
and drill two 3/16" holes.
Insert plastic anchors (U) into the two
holes on wall as shown. Use a hammer
to insert the plastic anchors until they
are flush with the wall.
Then attach the brackets (S) onto the
wall using screws (W).
Tighten screws (W) using Philips
screwdriver.
Figure 23
Move this item close to the wall brackets
(S) and tie in all brackets (S) together
with plastic strap (T) as shown in
diagram.
Anti-tipping hardware must be used for
this product to avoid tipping and injury.
Page 17

Figure 24
Now you Manchester fireplace console
is ready for use.

Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame.Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at serv[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 4
Page11