Southern Enterprises HZ104300TX User manual

Page | 1
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]m
www.seidal.com
HZ104300TX
Redding Bar Cabinet
Assembly Instructions
PO#:

Page | 2
Redding Bar Cabinet
Assembly Instructions
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
A.
Quantity
of 1
Top Panel
B.
Quantity
of 1
Bottom Panel
C.
Quantity
of 1
Left Side Panel
D.
Quantity
of 1
Right Side Panel
E.
Quantity
of 1
Upper Middle Panel
F.
Quantity
of 1
Upper Fixed Panel
G.
Quantity
of 1
Fixed Shelf Panel
H.
Quantity
of 1
Adjustable Panel
I.
Quantity
of 1
Left Door
J.
Quantity
of 1
Right Door
K.
Quantity
of 1
Upper Turnover Door
L.
Quantity
of 1
Back Panel

Page | 3
M.
Quantity
of 4
Leg
N.
Quantity
of 1
Mirror
O.
Quantity
of 1
Upper Door Handle
P.
Quantity
of 2
Lower
Door
Handle
1.
Quantity
of 16
Cam Bolt
2.
Quantity
of 16
Cam Lock
3.
Quantity
of 20
Wood Dowel Ø 8 x 30mm
4.
Quantity
of 2
Magnet
5.
Quantity
of 30
Round Head Screw
Ø 1/8” x 1/2”L
(for Back Panel and Magnet)
6.
Quantity
of 11
Screw Ø 1/8” x 1/2”L
(For Handle)
7.
Quantity
of 4
Shelf Pin
8.
Quantity
of 4
Hinge
9.
Quantity
of 24
Screw Ø1/8” x 5/8”L
(For Hinge )

Page | 4
10.
Quantity
of 4
Round Head Bolt
11.
Quantity
of 4
T- Nut
12.
Quantity
of 2
Bolt For
Semicircle H
inges
13.
Quantity
of 16
Bolt for Leg Ø1/4”x5/8
”L
14.
Quantity
of 16
Flat Washer Ø1/4”
15.
Quantity
of 16
Spring Washer Ø1/4”
16.
Quantity
of 1
Left Support
17.
Quantity
of 1
Right Support
18.
Quantity
of 10
Flat Head Screw for Support
Ø
1/8
”
x
1/2
”
L
19.
Quantity
of 4
Flat Head Screw
Ø 1/8” x 5/8”L
(For Bracket)
20.
Quantity
of 4
Screw
Ø
1/8
”
x
1
-
1/
2”
L
21.
Quantity
of 4
Anchor
22.
Quantity
of 4
Bracket
23.
Quantity
of 2
Plastic Strap
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call customer service at 1-800-633-5096.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)

Page | 5
Figure 1
Screw with fingers to help align screws
before using screwdriver.
Attach Magnets (4) to Top Panel (A)
using Flat Head Screws (5).
Tighten Flat Head Screws (5) with
Phillips screwdriver.
Figure 2
Screw with fingers to help align cam
bolts before using screwdriver.
Insert Cam Locks (2) into corresponding
holes on Upper Fixed Panel (F).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Upper Middle Panel (E).
Attach Upper Fixed Panel (F) to Upper
Middle Panel (E) by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Upper Fixed
Panel (F) and Upper Middle Panel (E)
meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Notice: Make sure that all finished
edges are facing towards the front of
the unit.
Redding Bar Cabinet
Assembly Instructions

Page | 6
Figure 3
Insert Cam Locks (2) into corresponding
holes on Upper Middle Panel (E).
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Fixed Shelf Panel (G).
Attach Upper Fixed Shelf Panel (G) to
assembled unit by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Upper Fixed
Shelf Panel (G) and the assembled unit
from Figure 2 meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 4
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 3.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Right Side Panel (D).
Attach Right Side Panel (D) to the
assembled unit from Figure 3 by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Right Side Panel (D) and assembled
unit from Figure 3 meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
3
3

Page | 7
Figure 5
Insert Cam Locks (2) into corresponding
holes on assembled unit from Figure 4.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Left Side Panel (C).
Attach Left Side Panel (C) to the
assembled unit from Figure 4 by
inserting Wood Dowels (3) and Cam
Bolts (1) into corresponding holes until
Left Side Panel (C) and the assembled
unit from Figure 4 meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
Figure 6
Insert Cam Locks (2) into corresponding
holes on the assembled unit from Figure
5.
Screw Cam Bolts (1) and insert Wood
Dowels (3) into corresponding holes on
Top Panel (A).
Attach Top Panel (A) to the assembled
unit from Figure 5 by inserting Wood
Dowels (3) and Cam Bolts (1) into
corresponding holes until Top Panel (A)
and the assembled unit from Figure 5
meet.
Tighten by rotating Cam Locks (2)
clockwise with Phillips screwdriver.
1
3

Page | 8
Figure 7
Insert T-Nuts (11) into corresponding
holes on the bottom of Side Panels
(C/D).
Attach Bottom Panel (B) to the
assembled unit from Figure 6 by
inserting Wood Dowels (3) into
corresponding holes until panels meet.
Insert Bolts (10) though corresponding
holes on bottom of Bottom Panel (B)
and into T-nuts (11).
Tighten Bolts (10) with Phillips
screwdriver.
Figure 8
Insert Mirror (N) into upper backside of
the assembled unit by hand as shown.
3
11

Page | 9
Figure 9
Attach Back Panel (L) to backside of the
assembled unit from Figure 8 with
Round Head Screws (5).
Tighten Screws (5) with a Phillips
screwdriver.
Note: Make sure the arrow on the rear
of the Back Panel (L) is pointing up.
F igure 10
Attach Legs (M) to Bottom Panel (B)
with Bolts (13), Spring Washers (15) and
Flat Washers (14) as shown.
Tighten Bolts (13) with Phillips
screwdriver.

Page | 10
Figure 11
Attach Hinges (8) to Door Panels (I) and
(J) with Screws (9) as shown.
Tighten Screws (9) with Phillips
screwdriver.
Figure 12
Attach Door Panels (I/J) to the
assembled unit from Figure 10 with
Screws (9) as shown.
Tighten Screws (9) with Phillips
screwdriver.
9