Southern Enterprises MS998400TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
customer service 1-800-633-5096
www.seidal.com
[e-mail]
MS998400TX
Landis TV/Media Console
Assembly Instructions
PO#：
Page 1

A
Quantity
of 1
top panel
B
Quantity
of 1
fixed shelf panel
C
Quantity
of 1
bottom panel
D
Quantity
of 1
left side panel
E
Quantity
of 2
right side panel
F
Quantity
of 1
vertical panel
G
Quantity
of 1
left door
H
Quantity
of 1
right door
I
Quantity
of 2
adjustable shelf
J
Quantity
of 1
top back panel
K
Quantity
of 1
bottom back panel
1
Quantity
of 16
wood dowel
Dia 5/16” x 1-3/16”L
2
Quantity
of 16
cam bolt
3
Quantity
of 16
cam lock
4
Quantity
of 4
hinge
Landis TV/Media Console
Parts list
Please review all parts and hardware before disposing of any packaging. Unpack and lay parts on
clean, padded surface like carpet or blanket. Check that you have all parts indicated.
Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware
according to the pictures. Using the incorrect hardware will cause damage.
Page 2

5
Quantity
of 28
short screw: Dia 1/8” x 1/2”L
6
Quantity
of 25
round head screw: Dia 1/8” x
1/2”L
7
Quantity
of 2
handle
8
Quantity
of 4
small bolt
9
Quantity
of 2
wall bracket
10
Quantity
of 8
shelf pin
11
Quantity
of 4
anchor
12
Quantity
of 4
long screw: Dia 1/8” x 1-3/8”L
13
Quantity
of 4
medium screw: Dia 1/8” x 5/8”L
14
Quantity
of 2
magnet
15
Quantity
of 2
plastic strap
16
Quantity
of 16
sticker cover
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish.Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Assembly Tool Required No.2 Phi
Tool List: 3/16" drill bit, drill, ta e measure and encil.
Page 3
Assembly Tool Required No.2 Philli s
Screwdriver (Not included)

Figure 1
Insert cam locks (3) into holes on
vertical panel (F). Screw cam bolts
(2) into holes on fixed shelf panel
(B).
Attach vertical panel (F) to fixed
shelf panel (B) by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes until vertical
panel (F) and fixed shelf panel (B)
meet.
Tighten by rotating cam locks (3)
clockwise with phillips screwdriver.
Repeat procedure to attach bottom
panel (C) to vertical panel (F).
Cover cam locks with sticker
covers(16)
Figure 2
Insert cam locks (3) into holes on
pre-assembled unit. Screw cam
bolts (2) into holes on left side panel
(D).
Attach pre-assembled unit to left
side panel (D) by inserting wood
dowels (1) and cam bolts (2) into
corresponding holes until
pre-assembled unit and left side
panel (D) meet.
Tighten by rotating cam lock (3)
clockwise with phillips screwdriver.
Repeat procedure to attach right
side panel (E) to (B) and (C).
Cover cam locks with sticker
covers(16)
Landis TV/Media Console
Assembly Instructions
Page 4
3
2
3
3
3
3
1
1
1
2
2
2
2
2
1
B
3
3
3
2
1
1
1
2
2
1
2
16
16

Figure
3
Insert cam locks (3) into holes on
pre-assembled unit as shown.
Screw cam bolts (2) into holes on
the underside of top panel (A).
Attach pre-assembled unit to top
panel (A) by inserting wood dowels
(1) and cam bolts (2) into
corresponding pre-drilled holes until
pre-assembled unit and top panel
(A) meet.
Tighten by rotating cam lock (3)
clockwise with phillips screwdriver.
Cover cam locks with sticker
covers(16)
Figure 4
Attach top back panel (J) & bottom
back panel (K) to the backside of
pre-assembled unit with screws (6).
Tighten screws with phillips
screwdriver.
Page 5
A
1
1
11
K
J

Figure
5
Attach hinges (4) to pre-assembled
unit, left door (G), and right door (H)
with screws(5)
Tighten screw with phillips
screwdriver.
Attach handles (7) to doors using
small bolts (8).
Attach magnets (14) to vertical
panel (F) with screws (6).
Tighten screws and small bolts with
Phillips screwdriver.
Figure 6
Insert shelf pins (10) into holes on
pre-assembled unit.
Place adjustable shelves (I) onto
shelf pin (10) as shown.
Page 6
10 10
10 10
II
14 14

Figure
7
Attach wall brackets (9) to back
panel using screws (13) and tighten
screws using phillips screwdriver.
Mark two desired locations on the
wall and drill two 3/16" holes. Insert
plastic anchors (11) into the two
holes on wall as shown. You will
need a hammer to help you.
Then attach the wall brackets (9) to
wall using screws (12) and tighten
screws using phillips screwdriver.
Figure 8
Move the item close to the wall
brackets (9) and tie both wall
brackets (9) with plastic strap (15)
as shown in diagram.
Anti-tipping hardware must be
used for this product to avoid
tipping and injury.
Figure 9
Your Landis TV/Media console is
ready for use.
Page 7
wall
1 1 14
1 2
1 4
1 4
1 3
13
1 2
1 1
9
9

Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are
not responsible for any damages due to product modification(s). If damages or missing parts are not reported within
90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central time if
you have product issues or email us at [e-mail]. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with
product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Re lacement Form
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 8

CAUTION
The top shelf is intended for a flat screen television with a maximum overall width of 40” and
supports up to 0 lb.
The top shelf is not intended for tube televisions.
Each shelf should not be loaded with more than 20 lb.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the
maximum size and weight indicated may result in instability causing possible injury.
This unit contains a permanent warning sticker located on back panel.
Do not allow children under 16 years to move the cart.
Model: MS99 400TX
Landis TV/Media Console
Southern Enterprises, Inc
600 Freeport Parkway,
Suite 200 Coppell, Texas, 75019
Manufacture Date: 19/12/2013