Soyer PH-9 SRM12 User manual

GB
Operating manual
Stud welding device
SRM technology
BMK-8i
Stud welding gun PH-9 SRM12
PH-9 SRM12+G
PH-3N SRM

GB
Device numbers
We recommend registering the device numbers here so they can be quickly ac-
cessed if service is needed.
Operating manual
Document no.: P00158, 01-2017, translation of the original manual
(English: P00258)
All information in this document is the property of
Heinz Soyer Bolzenschweißtechnik GmbH.
Device Type Serial number
Stud welding device BMK-8i
Stud welding gun PH-9 SRM12
PH-9 SRM12+G
PH-3N SRM
Revision status
Document Created/modified Editor Date
Original Prepared DD 23.01.2017

Operating manual Soyer Bolzenschweißtechnik 3
CONTENTS
1. General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1. Validity of the operating manual 6
1.2. Registered trademarks 6
1.3. Abbreviations and definitions 7
1.4. Declarations of conformity 7
1.5. Manufacturer 9
1.6. Instruction, training 9
1.7. Standards and directives 9
2. Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1. Safety alerts used 10
2.2. General safety instructions 11
2.3. Safety instructions for the working method 14
2.4. Personal protection equipment 15
2.5. Intended use of the stud welding device 16
2.5.1 Incorrect use 16
2.6. Intended use of the stud welding guns 16
2.6.1 Incorrect use 16
2.7. Operating company prerequisites 17
2.7.1 Prerequisites for personnel 17
3. Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Storage, shutdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5. Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Description of the BMK-8i stud welding device . . . . . . . . . . . . . . . . . . . . . . . 19
6.1. Type designation 19
6.2. Working method 19
6.2.1 Stud welding with SRM technology 20
6.2.2 Drawn arc stud welding technology with shielding gas 21
6.3. Overview of the controls 22
6.3.1 Display and setting area 24
6.4. Technical data of the BMK-8i stud welding device 25
6.5. Permitted stud welding guns 26

4 Operating manual Soyer Bolzenschweißtechnik
CONTENTS
6.6. Cleaning the stud welding device 27
7. Description of the SRM stud chuck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7.1. Setting the SRM stud chuck 28
8. Description of the PH-9 SRM12 stud welding gun . . . . . . . . . . . . . . . . . . . . . . 30
8.1. Technical data of the PH-9 SRM12 stud welding gun 31
8.2. Installing the SRM stud chuck in PH-9 SRM12 32
8.3. Replacing the SRM12 support tube insert with PH-9 SRM12 34
8.4. Cleaning the stud welding gun 35
9. Description of the PH-9 SRM12+G stud welding gun . . . . . . . . . . . . . . . . . . . 36
9.1. Technical data of the PH-9 SRM12+G stud welding gun 37
9.2. Operation of the PH-9 SRM12+G 38
9.2.1 Safety check 38
9.2.2 Welding with the PH-9 SRM12+G 39
9.3. Installing the SRM stud chuck for the PH-9 SRM12+G 39
9.4. Replacing the SRM12 support tube insert with the PH-9 SRM12+G 42
9.5. Cleaning the stud welding gun 44
10. Description of the PH-3N SRM stud welding gun . . . . . . . . . . . . . . . . . . . . . 45
10.1. Technical data of PH-3N SRM stud welding gun 46
10.2. Installing the SRM stud chuck with PH-3N SRM 47
10.3. Cleaning the stud welding gun 49
11. Setup and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
11.1. Requirements for the installation location 50
11.2. Connection of the stud welding device and the stud welding guns 51
11.2.1 Mains connection 51
11.2.2 Connecting the earth cable 51
11.2.3 Connecting the stud welding gun 52
11.2.4 Connecting the shielding gas supply 52
12. Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
12.1. Setting the welding parameters 56
12.1.1 Help tables for device setting 56
12.1.2 Setting the welding current and the welding time 58
12.1.3 Setting/deactivating the SRM current 59

Operating manual Soyer Bolzenschweißtechnik 5
CONTENTS
12.1.4 Setting the gas preflow time 60
12.1.5 Setting the lift time (height of lift) in "Setup" mode 61
13. Welding operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
13.1. Carrying out welding 64
13.2. Notes on checking the quality of the weld 66
13.2.1 Visual inspection 66
13.3. Switching off the Device 67
13.4. Weld defects and their causes 68
14. Maintenance and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
15. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
16. Warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

General information
6 Operating manual Soyer Bolzenschweißtechnik
1. General information
This operating manual contains important information and requirements for op-
erating the devices. Keep the operating manual in a readily accessible location
close to the devices.
The term 'Devices' in the operating manual refers to the stud welding device and
the stud welding gun.
Carefully read through the operating manual and the other documents
contained in the technical documentation. In particular, comply with the safety
instructions which are intended to help you recognise any residual risks and
prevent hazards.
The drawings and diagrams in this operating manual help illustrate the content
and may vary slightly from the actual equipment.
The manufacturer reserves the right to make technical changes.
1.1 Validity of the operating manual
This operating manual applies to the following devices:
1.2 Registered trademarks
The following terms in this manual are marked with registered trademarks:
Stud welding device BMK-8i
Stud welding guns PH-9 SRM12
PH-9 SRM12+G
PH-3N SRM
SRM®: SRM stands for magnetic field stud welding and refers to welding
or stud welding in a radially symmetrical magnetic field.
SOYER®: Developments/technologies of Soyer GmbH.

General information
Operating manual Soyer Bolzenschweißtechnik 7
1.3 Abbreviations and definitions
Essential abbreviations or designations in this manual:
1.4 Declarations of conformity
The devices are built according to the generally accepted codes of practice.
HZ-1 threaded studs: SOYER universal studs with centring tip.
MF threaded studs: SOYER threaded stud with a reduced flange diameter
(MF stands for mini flange).
i
Please note that significant modifications to the device can void the
declaration of conformity.
In addition, the manufacturer warranty coverage may be rendered inva-
lid.

General information
8 Operating manual Soyer Bolzenschweißtechnik
Stud welding device
Heinz Soyer Bolzenschweißtechnik GmbH
Inninger Straße 14
82237 Wörthsee
CE Declaration of Conformity
We herewith declare that the machine described in the following and the version available on the
market correspond in design and construction to the safety and health requirements of the listed
guidelines and standards. Any unauthorised modification to this machine automatically annuls this
declaration.
Designation of machine : Stud welding device
Machine type : BMK-8i
Machine no. : ______________________
Applicable EU directives : RoHS Directive (2011/65/EU)
Low Voltage Directive (2014/35/EU)
EMC Directive (2014/30/EU)
Applied harmonised : EN 60 974-1:2012
standards, in particular EN 60 974-10:2008
Applied national standards : DGUV Regulation 1
Date : 17 May 2016
Producer’s signature : ____________________
Signer’s function : Managing Director

General information
Operating manual Soyer Bolzenschweißtechnik 9
1.5 Manufacturer
The manufacturer of the devices is: Heinz
Soyer Bolzenschweißtechnik GmbH
Inninger Straße 14
82237 Wörthsee
Tel.: [phone]
Fax: [phone]
Mail: [email protected]
Web: www.soyer.de, www.soyer.com
1.6 Instruction, training
Soyer offers optional and individual instruction in the operation of the devices.
Soyer also offers training for customer-specific use of the devices.
Information about the scope and costs of instruction and training can be obtained
from Soyer GmbH.
1.7 Standards and directives
The following standards (among others) must be observed for carrying out stud
welding work and for the qualification of personnel:
• DIN EN ISO 14555 Welding - Arc stud welding of metallic materials
• DIN EN ISO 14732 Welding personnel - Qualification testing of welding oper-
ators and weld setters for mechanized and automatic welding of metallic ma-
terials
• DIN EN 60974-9 Arc welding equipment - Installation and use
• DVS data sheet 0904 Practical tips - Arc stud welding

Important safety instructions
10 Operating manual Soyer Bolzenschweißtechnik
2. Important safety instructions
Read the following chapter carefully and follow the safety instructions. If you are
uncertain or an instruction cannot be followed, please contact the manufacturer.
The devices have been built according to the generally accepted codes of prac-
tice and in compliance with, and application of, the usual and established safety
requirements. To achieve the maximum possible safety, it is essential that all of
the safety instructions in this operating manual are heeded and followed.
2.1 Safety alerts used
Warning signs are used in this document, depending on the potential danger of
the situation.
Safety and information symbols used in this manual
This safety alert indicates an imminently hazardous
situation which will result in serious injury or death.
This safety alert indicates a potentially dangerous
situation which could result in serious physical
injury or death.
This safety alert indicates a potentially hazardous
situation which could result in minor or moderate
injury.
This alert, without the triangle, is also used for
potentially hazardous situations which will result in
property damage.
Additional information indicating danger from elec-
tric current. The additional information is used in
conjunction with a warning sign.
Additional information on the risk of burns. The
additional information is used in conjunction with a
warning sign.
Do not touch the surface of the housing, danger of
electrocution.
Do not touch or open, danger for unauthorised per-
sons.
Danger for persons with a heart pacemaker or
other medical implants.
The info sign is not a safety alert. It indicates impor-
tant and useful information on the subject.
DANGER
!
WARNINGWARNING
!
CAUTIONCAUTION
!
i

Important safety instructions
Operating manual Soyer Bolzenschweißtechnik 11
Safety instruc-
tions on the de-
vice
There may be warning stickers on the devices as additional warnings of
danger. The warning stickers are affixed by the manufacturer and must not be
removed. If a warning sticker is damaged and thus illegible, a new warning
sticker must be affixed immediately.
The warning stickers must be obtained from the manufacturer.
2.2 General safety instructions
DANGER
!
Danger due to electric current, general information
When working on current-carrying components, there is a danger to life from
electric current.
• Work on electrical or electronic modules may only be carried out by elec-
trotechnically qualified personnel and carried out in line with the currently
applicable electrotechnical regulations.
•Protection equipment must not be manipulated or disabled. Protection
equipment includes, for example, the housing and housing cover, fuses
and device switches.
•If protection devices have to be removed for maintenance work, the device
must only be switched on again when all protection devices are mounted
again and their functionality has been checked.
•Starting the device with defective protection equipment is not allowed.
Repair or replace faulty protective equipment immediately. Unwanted
operation by a third party must be prevented.

Important safety instructions
12 Operating manual Soyer Bolzenschweißtechnik
DANGER
!
Danger from electric current during maintenance and repair
When working on current-carrying components, there is a danger to life from
electric current.
• Work on electrical or electronic components must only be carried out by
electrical specialists from Soyer Bolzenschweißtechnik.
•Before working on the stud welding device, the mains switch of the device
must be switched off and the mains plug of the stud welding device
discon-nected.
•Before working on the stud welding gun, the supply cable to the stud weld-
ing device must be disconnected.
•If protection devices have to be removed for maintenance work, the device
must only be switched on again when all protection devices are mounted
again and their functionality has been checked.
DANGER
!
Danger from magnetic fields
Strong magnetic fields occur in the area of the device, which may affect the
operation of medical aids, causing a danger to life.
• Persons with electrical medical aids (such as pacemakers) must keep
away from the devices.
•The operating personnel must ensure that persons with medical aids keep
away from the devices.
DANGER
!
Danger of explosion from an inappropriate installation location in explo-
sive atmospheres
The device is not designed for use in explosive zones.
• The device may not be installed and operated in explosive atmospheres.

Important safety instructions
Operating manual Soyer Bolzenschweißtechnik 13
CAUTIONCAUTION
!
Danger of burns due to hot surfaces
Through the welding process, the workpieces and some parts of the welding
gun become so hot that touching them can lead to burns.
• Always use personal protective equipment.
• Before beginning work on hot parts of the device, check that they have
cooled down.
• Do not hold the gun tight in the welding area.
WARNINGWARNING
!
Danger of burns from hot welding spatter
Dangerous welding spatter can occur during the welding process.
• Always use personal protective equipment.
WARNINGWARNING
!
Danger of burns from hot welding spatter
Welding spatter or hot workpieces occurring due to the welding process can
result in a danger of burns.
• Do not store any inflammable and combustible materials in the welding
area.

Important safety instructions
14 Operating manual Soyer Bolzenschweißtechnik
2.3 Safety instructions for the working method
WARNINGWARNING
!
Hazards due to incorrect working method
Hazards for operators and third parties can arise due to an incorrect working
method.
• Ensure sufficient stability and a dry installation location for the stud welding
device.
• Make sure you do not knock over the stud welding device or pull it down
from its position with the gun cables.
• Make sure, especially with mobile use, of your own good stability during
welding.
•Do not hold the workpiece in your hands during welding. The workpiece
must be securely fixed during the welding process.
• Never wrap the gun lines around parts of your body (e.g. arm) as electric
fields can occur.
• If the gun is not put on properly or the gun settings are incorrect, a flash
can occur during welding. Do not look directly into the flash.
• The gun carries out lifting movements during the welding process. Do not
hold the gun tight in the area of moving parts.

Important safety instructions
Operating manual Soyer Bolzenschweißtechnik 15
2.4 Personal protection equipment
The wearing of personal protective equipment is recommended when working
with the stud welding device.
WARNINGWARNING
!
Danger due to missing or incorrect personal protection kit
There is a danger of burns during stud welding, especially due to hot welding
spatter. A danger of blinding can also arise due to the occurrence of strong
arcs.
• Always wear suitable, closed protective clothing.
• The extent of the protective equipment depends on the respective occur-
rence and intensity of the welding spatter, arcs and/or noise. This varies
according to the basic material, stud material, stud size and required weld-
ing power.
• Heed the instructions concerning protective equipment in the following
overview.
Recommended personal protection equipment
Protective goggles
During welding, welding spatter and a flash occur. Wear
suitable safety goggles with side protection and protect
your eyes with filter protection if necessary.
Protective gloves
During welding, the workpieces and parts of the welding
gun become hot and welding spatter can occur. Wear suita-
ble, non-combustible, heat-resistant protective gloves.
Protective clothing
Welding spatter occurs during welding. Wear suitable, non-
combustible and, if necessary heat-resistant, protective
clothing.
Safety shoes
Welding spatter occurs during welding. Wear suitable, non-
combustible, heat-resistant safety shoes.
Hearing protection
Depending on the welding device and the welding applica-
tion, relatively loud welding noise can occur. Wear suitable
hearing protection.

Important safety instructions
16 Operating manual Soyer Bolzenschweißtechnik
2.5 Intended use of the stud welding device
Pins and threaded studs from M3 - M8 (M6 and M8 preferred) made of steel and
stainless steel can be welded using the SOYER BMK-8i stud welding device.
Special studs or diameters on request.
The stud welding device must only be operated with the welding guns described
in chapter "6.4 Technical data of the BMK-8i stud welding device" on page 25.
The stud welding device must be operated within the technical specifications.
Only welding studs from Soyer (HZ-1 and MF types) must be welded.
The stud welding device supports the following welding processes:
• SRM welding (stud welding in a radially symmetrical magnetic field)
• Drawn arc stud welding with shielding gas
2.5.1 Incorrect use
Any use other than the intended use of the device is deemed to be non-intended.
Use other than intended use, unauthorised modification or manipulation of the
device will void the declaration of conformity as well as all warranty claims
against the manufacturer.
2.6 Intended use of the stud welding guns
Pins and threaded studs from M3 to M12 and numerous different weld fasteners
according to DIN EN ISO 13918, made of steel, stainless steel, aluminium and
brass, can be welded with the SOYER stud welding guns described in this oper-
ating manual.
2.6.1 Incorrect use
Special studs or diameters on request.
The operation of welding guns is only permitted with the stud welding devices de-
scribed in the technical data of the gun.
The stud welding gun must be operated within the technical specifications.
Any use other than the intended use of the welding gun is deemed to be contrary
to the intended use.
Use other than the intended use, unauthorised modification or manipulation of the
device will void the declaration of conformity as well as all warranty claims
against the manufacturer.
i
The maximum diameter and type of weldable studs can be limited by the
performance capacity of the stud welding device on which the gun is
operated.

Important safety instructions
Operating manual Soyer Bolzenschweißtechnik 17
Misuse of the welding gun as a tool, e.g. as a hammer for checking the weld qual-
ity, is not permitted.
2.7 Operating company prerequisites
The operator of the device must ensure that the preconditions in this operating
manual are fulfilled for safe operation.
These include, for example, the conditions at the installation site, the official reg-
ulations on requirements for a safe workplace, the training of the operating per-
sonnel and qualified personnel in handling the device if necessary, fulfilment of
the prescribed maintenance work, and monitoring that the device is used in con-
formity with intended use.
The operating manual must be stored in the vicinity of the device.
The device operating company must ensure that the device is only used when all
protective equipment is present, active and undamaged.
2.7.1 Prerequisites for personnel
Operating per-
sonnel
Electrical and
electronic spe-
cialists
The personnel responsible for operating the device in normal operation must be
familiar with the device and trained accordingly. They must have read and
understood the operating manual. In addition, they must be capable of
eliminating (or minimising as far as possible) any possible remaining danger to
themselves and third parties when working with the device.
To retain this qualification, the safety training must be repeated annually. In the
event of a fault or if maintenance becomes necessary, consult specially trained
qualified personnel or the manufacturer.
Operators of stud welding equipment must have the expert knowledge for oper-
ating, correctly setting the equipment and for properly carrying out the welding.
If the welders have to be qualified for certification of welding, the
DIN EN ISO 14555 and DIN EN ISO 14732 standards must be observed.
The following basically applies: Work on current-carrying elements may only be
performed by qualified electricians. The work must be carried out in line with the
applicable technical rules for electrotechnical devices.
i
All devices of Soyer Bolzenschweißtechnik GmbH must only be opened
by Soyer personnel or by personnel authorised by Soyer.

Transport
18 Operating manual Soyer Bolzenschweißtechnik
3. Transport
When transporting the device, make sure it cannot be damaged. It must be pro-
tected against the effects of weather, especially moisture, through suitable pack-
aging.
4. Storage, shutdown
Protect the device against dirt and humidity during storage or shutdown.
Protect the device against unauthorised access by third parties.
5. Disposal
Local environmental guidelines for disposal must be complied with.
Substances that are hazardous to water and the environment must be disposed
of in accordance with legal regulations.
Materials must be separated according to regulations where applicable.

Description of the BMK-8i stud welding device
Operating manual Soyer Bolzenschweißtechnik 19
6. Description of the BMK-8i stud welding device
The main elements of the stud welding device are shown and the function de-
scribed in the following.
6.1 Type designation
6.2 Working method
Pins and threaded studs from M3 - M8 (M6 and M8 preferred) made of steel and
stainless steel can be welded using the SOYER BMK-8i stud welding device.
Only welding studs from Soyer (HZ-1 and MF types) must be welded.
The BMK-8i working with SRM technology was specially developed for mobile
use. Thanks to SRM, the BMK-8i mobile welding device enables problem-free
welding, even in constrained positions.
The BMK-8i works on the basis of a compact inverter current source and delivers
a constant welding current up to 300 A with extremely short welding times. The
rectified mains voltage is converted into a high frequency voltage with a frequency
of 75 kHz by an Insulated Gate Bipolar Transistor-based (IGBT-based) inverter.
The energy is transferred by a high frequency transformer and rectified on the out-
put side. As a result of the high control speed in combination with the integrated
SRM welding process of the BMK-8i, the reproducibility of the welds is increased
and the quality of the welding significantly improved.
Designation
Order number Feature
BMK-8i
P01363
Mains voltage 230 V 1PH/N/PE

Description of the BMK-8i stud welding device
20 Operating manual Soyer Bolzenschweißtechnik
The PH-9 SRM12 and PH-9 SRM12+G stud welding guns or the PH-3 SRM stud
welding gun, with an adapter, can be connected as standard guns to the BMK-8i
stud welding device.
6.2.1 Stud welding with SRM technology
The welding process recommended by Soyer for operating the BMK-8i is the pat-
ented SRM welding process (patent no.: 10 2004 051 389) in conjunction with the
also newly developed HZ-1 universal studs with flat front face and centring tip
(patent no.: 10 2006 016 553).
SRM means stud welding in a radially symmetrical magnetic field.
This innovative weld technology allows welds in a ratio of 1:10 of the sheet thick-
ness to the stud diameter (previously 1:4) where the use of ceramic rings can be
dispensed with.
The versatile advantages of the SRM process provides completely new applica-
tion options in the entire stud welding sector (additional information available at
www.srm-technology.de).
Functional principle
The advantages of the SRM welding process are:
• No bothersome weld bead
• Welding from constrained positions now also without ceramic ring
• Reduced weld penetration in the plate
• Lower energy consumption and reduced welding time
• No welding spatter
The stud tip touches the
workpiece and is lifted.
The arc is initiated.
The ignited arc is guided
by a magnetic field and
melts both joint parts
fully.
The stud immerses in
the very flat weld pene-
tration zone and is sol-
idly connected.
i
Further information on this subject can be found at www.soyer.com.