Speco O2MD2 User manual

O2MD2
Owner’s Manual
O2MD2

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
2
Caution
Any changes or modifications in construction of this device which are not explicitly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generate, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Directions
Be careful not to cause any physical damage by dropping or throwing the camera.
Especially keep the device out of reach from children.
Do not disassemble the camera. No after service is assumed when disassembled.
Use only power adapters compatible with the unit.
Be careful to prevent moisture or water penetration into the unit. Particular attention is
needed when installing the unit. The screw holes for the installation screws and pipe should
be maintained water tight during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from
the outside cannot flow into the unit through the surface of the wires. Penetration of the
moisture through the wire for extended period can cause malfunction of the unit or
deteriorated image.

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
3
Revision History
Date
Revision
Details
Mar 27th, 2014
1.0
First manual revision creation.

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
4
Contents
1. Introduction....................................................................................................................................................5
1.1. Overview...................................................................................................................................................5
1.2. Specification..............................................................................................................................................6
1.3. Applications of O2MD2.............................................................................................................................7
2. Product Description ......................................................................................................................................8
2.1. Contents ...................................................................................................................................................8
2.2. Product Preview........................................................................................................................................8
2.3. Physical description..................................................................................................................................9
2.3.1. External View..................................................................................................................................9
2.3.2. Dimension.......................................................................................................................................9
2.3.3. External Connector.......................................................................................................................10
2.4. Functional Description............................................................................................................................11
3. On Site Installation ......................................................................................................................................12
4. Getting Started.............................................................................................................................................13
4.1. PC Requirement.....................................................................................................................................13
4.2. Quick Installation Guide..........................................................................................................................14
4.2.1. Connect PC and O2MD2 to network............................................................................................14
4.2.2. Install Speco-NVR and set IP parameters on O2MD2 .................................................................14
4.2.3. Remote video connection to O2MD2 ...........................................................................................17
4.2.4. Additional settings through connection to the Admin Page..........................................................19
5. Trouble Shooting .........................................................................................................................................20
5.1. No power is applied................................................................................................................................20
5.2. Cannot connect to the Video..................................................................................................................21
5.3. Windows Vista or Windows 7 .................................................................................................................22
5.4. Technical Assistance...............................................................................................................................25

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
5
1. Introduction
1.1. Overview
O2MD2 is multi-codec (H.264, MJPEG) IP camera (or network camera) built with embedded software and
hardware technology in pancake housing. It enables real time transmission of video of up to 1080P. Remote
clients can connect to O2MD2 for the real time video data through various client solutions running on PC or
smart device.
O2MD2 is specialized in video transmission which economic and practical products removing audio, sensor,
replay, etc and the videos can be only available in the field and place where needed.
Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of
Ownership) by reducing on-site wiring works for the installation.

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
6
1.2. Specification
Camera
Image sensor
Progressive scan 1/2.9 inch CMOS 2.0M pixels
Full resolution
1,920 x 1,080 pixels (Full HD)
Min. illumination
0.2Lux (Color, DSS On), 0.00 Lux (IR LED On)
S/N Ratio
50dB or more
White Balance
AWB
DSS
Supported
WDR
Supported
Lens
3.7mm, F2.5
Day & Night
Supported (TDN & IR LED)
IR LED
12EA
Video
Compression method
Simultaneous Dual Codec (H.264 / MJPEG)
Resolution
1920x1080@30fps
Multi-Profile Streaming
- 3 simultaneous video profiles
- Select the codec type, resolution and frame rates for each profile.
Intelligent Bit-Rate Control
VBR or CBR
PTZ
Digital PTZ & video crop
Image Setting
Text overlay, Privacy mask, De-interlace filter
Motion detection
3 regions
Network
Network Protocol
- IPv4/v6, TCP, UDP, IGMP, ICMP, ICMPv6, ARP, RARP, PPPoE, RTCP
- RTP, RTSP, SDP, HTTP, HTTPS, SMTP, FTP, DHCP, UPnP
- NTP, DNS, DynDNS, SOCKS
Dynamic IP
Speco DDNS (free of charge)
Security
- User ID & Password protection, IP address filtering
- HTTPS encryption, Digest Authentication, User Access Log
Streaming method
- RTSP streaming with proprietary format for control informations
- Standard RTSP streaming
- HTTP streaming

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
7
External Terminals
LAN
10/100BaseT LAN (auto MDIX)
Power
DC 12V input
Factory Reset
Supported
Alternate Power
Standard PoE
IEEE802.3af Supported
Alarm & Event
Intelligent Video
Motion Detection
Alarm Triggers
Intelligent Video
Alarm Events
Video file upload(FTP), Still Image(Email)
Alarm Buffer (Audio/Video)
configurable Pre-alarm (5~10 sec) & Post-alarm (10~30 sec) 
Client Software
Speco NVR
Windows XP/Vista/7 (free of charge)
Speco ONSIP
Android™, iPhone® , iPad® (free of charge)
Miscellaneous
Operating Temperature
0C ~ 45C (32F~113F)
Operation Humidity
8~80% RH
Power
DC 12V, 0.6A
Dimensions(W x H x D)
Ø122mm(4.8”) x 55mm(2.1”)
Weight
0.4Kg (0.88Lb)
Casing
AL, PC
Approvals
FCC, CE, KCC, RoHS
Package information
Unit, CD, mounting screws
Optional Items
Adapter
DC 12V, 1.5A
1.3. Applications of O2MD2
Small Office, Home environment, Personal user.
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Weather and environmental observation

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
8
2. Product Description
2.1. Contents
The product package contains followings :
Contents
Description
Remarks
O2MD2
IP camera O2MD2 main unit
Accessories
Screws (3 pieces of 1 type),
Anchors (3 pieces of 1 type),
L-type wrench 1EA
CD
Software & User’s Guide
Quick Reference Guide
Quick installation guide
Power Adaptor
Default built in standard PoE module
(IEEE802.3af)
12V DC Adaptor
(Optional item)
2.2. Product Preview
O2MD2
IP Installer
VMS Software (Speco NVR)
Main Unit
PC software to allocate an IP
address to the IP Camera
PC software to view and record the
A/V streaming data transmitted from
IP camera.
(Simultaneous support of up to 64
IP cameras@D1)

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
9
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of O2MD2
2.3.2. Dimension
Unit : mm
Figure 2-2. Dimension

O
O2 2M MD D2 2 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.0 (Mar. 2014)
10
2.3.3. External Connector
Figure 2-3. Connector for external connection
Network (LAN)
Power