Speco O4P30X User manual

Quick Start Guide
4MP 30X PTZ IP Camera
O4P30X
Version 1.0.1

i
Ta le of Contents
1 DEVICE CHECK AND INSTALLATION ............................................................................ 1
1.1 Installation Requirements ......................................................................................... 1
1.2 Check Accessories ..................................................................................................... 1
1.3 Open the Device ....................................................................................................... 1
1.4 SD Card Installation ................................................................................................... 2
1.5 Reset ........................................................................................................................ 2
1.6 Speed Dome Installation ........................................................................................... 3
1.6.1 Quick Installation port ........................................................................................... 3
1.6.2 Cable Connection ................................................................................................... 3
1.6.3 Install the speed dome .......................................................................................... 4
2 BRACKET DIMENSIONS .............................................................................................. 6
2.1 Wall Mount Bracket .................................................................................................. 6
3 WALL MOUNT INSTALLATION .................................................................................... 7
3.1 Component Installation ............................................................................................. 7
3.2 Installation................................................................................................................ 7
3.2.1 Installation Requirements ...................................................................................... 7
3.2.2 Installation Steps ................................................................................................... 7
4 IP SCANNER .............................................................................................................. 9
4.1 Overview .................................................................................................................. 9
4.2 Operation ................................................................................................................. 9
5 WEB OPERATION .................................................................................................... 10
5.1 Login and Main Interface ......................................................................................... 10
6 APPENDIX Ⅰ
ⅠⅠ
Ⅰ SURGE PROTECTION ............................................................................. 11
7 APPENDIX Ⅲ
ⅢⅢ
Ⅲ 24V AC CABLE DIAMETER AND TRANSMISSION DISTANCE
RELATIONSHIP ................................................................................................................ 12

ii
8 APPENDIX IV WIRE GAUGE REFERENCE .................................................................... 13

iii
Welcome
hank you for purchasing this Network camera!
his manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco echnologies echnical
Support.

iv
Important Safeguards and Warnings
1．
．．
．Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must e grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2．
．．
．Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
his product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean the
device.
Please use a professional optical cleaning method to clean the enclosure. Improper
enclosure cleaning (such as using cloth) may result in poor IR functionality and/or IR
reflection.
he grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:
Stained with dirt
Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens

v
center outward. Change the cloth and wipe several times if it is not clean enough.
Warning
his camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
his guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
echnologies reserves the right to modify these without notice and without incurring any
obligation.
Speco echnologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Keep the package material in case the camera needs to be sent back for service or repair.
Contact your rep or Speco customer service department immediately if something is broken
or missing in the package.

1
1Device Check and Installation
1.1 Installation Requirements
Basic Requirement
All installation and operation here should conform to your local electrical safety codes.
Before installation, please open the package and make sure all components are included.
Please make sure the speed dome installation environment can meet your requirement.
If there is special requirement, please contact your local dealer for more information.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
1.2 Check Accessories
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken
or missing in the package.
Accessory Name Amount
Network Camera Unit 1
Quick Start Guide 1
Wall Mounting Bracket 1
Installation Accessories Bag 1
CD
1
1.3 Open the Device
Please open the box and then take out the speed dome.
Remove the bracket component, take out the EPE foam around the module, Figure 1-1.

2
Figure 1-1
1.4 SD Card Installation
Remove the bracket component; open the cover and locate the micro-SD card slot on the
module ISP board (see Figure 1-2).
Figure 1-2
1.5 Reset
Locate the reset button on the P Z mainboard after you remove the bracket component.
See Figure 1-3. Reset button is used to reset the camera back to factory default.

3
Figure 1-3
1.6 Speed Dome Installation
1.6.1 Quick Installation port
Now you can install the quick installation port. Please twist eflon tape around the screw
thread of the quick installation port and turn it into the screw thread of the wall mount
bracket. Use M4 stainless screws to secure firmly. See Figure 1-4.
Figure 1-4
1.6.2 Ca le Connection
Connect the safety hook of the intelligent speed dome cover to the hook of the quick
installation port.

4
Connect the necessary cables.
1.6.3 Install the speed dome
Step 1
Pull the cable to the wall mount bracket slowly.
Step 2
Line up the straight edge of the flange of the speed dome to the straight edge of the quick
installation port, and then push the speed dome to the bottom of the port slowly.
Step 3
Use your hands to turn the quick installation port M6*14 stainless screw (with spring washer)
to the Ф6.5 hole of the straight edge of the speed dome. urn other two M6*14 stainless
screws to groove of speed dome flange. Use the inner hex tool to fix these three stainless
screws. Now you have completed the installation. See Figure 1-5.
Figure 1-5
Step 4
Please make sure:
he three stainless screws of the quick installation port are firmly secured.
he speed dome is fixed.
he speed dome is straight.
he safety hook connection is firm.
After your installation, the interface is shown as in Figure 1-6.