Speco O2iB8M User manual

QUICK INSTALL GUIDE
O2iB8M
2MP Intensifier(R) IP Bullet Camera
Please read this guide carefully before operating
the unit and retain it forfuture reference.
This lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of uninsulated dangerous
voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
WARNING: This product contains chemicals known to the State of California to cause cancer
and birth defects or other reproductive harm. Wash hands after handling.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate
this equipment if an unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of
this product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have smooth well rounded
surfaces or shall be provided with brushings.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

• Extremely hot or cold places (operating
temperature 14 ℉ to 122 ℉ , however, we
recommend that the unit be used within
a temperature range of 32 ℉ to 113 ℉ )
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful
electromagnetic radiation such as radio
or TV transmitters.
• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.
Warning: Do not install this equipment in
a confined space such as a bookcase or
similar unit.
Note:
Please make sure the product is installed
appropriate places where secured from
flood, such as under the eaves, to operate
properly. This product is certified as IP66
standard. However, if there is any flood
concerns, it is highly recommended to use
an outdoor Housing. When you install the
camera inside an outdoor Housing, please
use one of the following methods:
1. Remove the front glass of Housing
before installing the camera.
2. To keep the front glass of Housing,
remove the front cover, and then put
the camera close to the front glass.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly
at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Be careful not to spill water or other liquids in the
unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to fail or to
get cause of fire or electric shock.
Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.
• Remove dust or dirt on the surface of the
lens with a blower.
• Use a soft and lint-free, dry cloth(such as
glass cleaner) to clean the body. If it is
very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.
• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.
• This camera is designed for mounting
on the ceiling or wall. If you install this
camera upside down, it may cause
malfunction.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Handling of the unit
Operating and storage
location
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
Important Safety
Instructions
Caution: Make sure the power supply voltage
is correct before using the camera.
Caution: Do not drop the camera or subject it
to physical shock.
Caution: While shipping, the camera should
be packed in its original packing.
Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.
Warning: To reduce a risk of fire or electric
shock, do not expose the internal apparatus
to rain or moisture
Warning: Install the camera on a ceiling or
wall where can withstand the weight of 5
times of the camera including mounting
bracket.
Caution: The internal apparatus shall not be
exposed to water (dripping or splashing) and
no objects filled with liquids, such as vases,
shall be placed within the enclosure
Caution: The sensor may be burned out by a
laser beam, so when any laser equipment is
being used, make sure that the surface of the
sensor not be exposed to the laser beam.
Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.
Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.
Warning: Please adopt the power adapter
which can meet the safety extra low voltage
(SELV) standard. And source with DC 12 V or
AC 24 V (depending on models) according
to the IEC60950-1 and Limited Power Source
standard.
Warning: This is a class A product. In a
domestic environment this product may
cause radio interference in which case the
user may be required to take adequate measures.
To disconnect power from mains, pull
out the mains cord plug. When installing
the product, ensure that the plug is easily
accessible.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

This guide includes instructions for installing and using this IP camera
Introduction
Features
•Multi-streams for live view and recording
•H.265/H.264/MJPEG compression algorithm
•Two-way audio communication
•True WDR operation
•Color in low light without IR LEDs
•Motorized zoom with auto focus
•Power sources: 12 VDC, PoE (Power over Ethernet)
•NTSC or PAL programmable video output
•IP66 compliant for weather resistance

MODEL
GENERAL
CAMERA
VIDEO
AUDIO
CONNECTORS
Lens Type
Lens Iris Control
LENS
Ethernet Port
Dimensions (Ø x H)
Operating Temperature
Operating Humidity
Power Supply
Power Consumption
Approval
Unit Weight
2.8mm-12mm Motorized Lens
DC Auto Iris
1/3” 2Mega CMOS Sensor
COLOR: 0.05Lux F1.4
BW: 0.0025 Lux F1.4
Progressive Scan
108dB (True WDR)
Auto / Manual(1/30(25) ~ 1/10,000)
Anti-Flicker, Slow Shutter(Off,1/15 sec~1/1 sec)
Wires
Wires
RJ-45
3.94”(W)X3.94”(H)X8.27”(D)
3.09lbs
14°F to 122°F(-10°C to 50°C)
0% to 90%
12 VDC, PoE(Power over Ethernet)(IEEE 802.3af, Class 3)
Max. 4.8W
FCC, CE, IP66
Image Sensor
Minimum Illumination
Scanning Mode
Dynamic Range (WDR)
Electronic Shutter
Compression Algorithm
Compression Algorithm
Compression Resolution
Bitrate Control
Maximum Frame Rate
H.265(MP/BP), H.264(HP/MP/BP), M-JPEG
352X240, 640X360, 704X480(D1), 1280X720(720P), 1920X1080(1080P), 2592X1520, Pivot
H.264 - CBR / VBR (up to 13Mbps)
H.264 - CBR / VBR (up to 7Mbps)
G.726 (16KHz), G.711 μ - Law (8KHz)
30ips @ 1080p + 30ips @ 720p + 30ips @ 4CIF Max Triple Streaming
1 line in
1 BNC
1 line Out
1 relay out, NO only, 0.3A @ 125 VAC, 1A @ 30 VDC
1TTL, NC/NO programmable, 4.3V (NC) or 0.3V (NO) threshold, 5 VDC
10/100 Mbps Ethernet
BNC
Φ 3.5 audio jack
Video Output
Video Output
Audio Intput
Audio Output
Alarm Input
Alarm Output
Network Connectivity
INPUS / OUTPUTS
Specification
O2iB8M
Alarm Out
Alarm In
Audio In/Out

3AXIS BRACKET
SCREW TS T1, 4X25, TH, SUS, 4EA
SCREW M5X10, HEXAGON SOCKET, SUS, BK, 4EA
WALL
Focus and zoom can be set remotely.