Speco O3FDP9 User manual

Flexible Intensifier® Technology Bullet IP Camera
QUICK INSTALLATION GUIDE
O3FDP9
Please read this guide carefully before installation and operation of the product.

1
Notice
Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read
it carefully before operating the product and retain it for future reference. Should you require any technical
assistance, please contact Speco Technologies Technical Support.
INFO MATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 5
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at its own expense.
WA NING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION – To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION

2
P ECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and to obtain
the best picture quality.
Installation and services should only be carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and
have it checked by your authorized dealer before reusing.
Avoid installing the camera in extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance
by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera in a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Don't point the camera directly at sunlight.
Please pay special attention to keep the unit from dropping or external shock during the process of
transportation or handling.
Never try to touch the camera with wet hands. It may cause an electric shock.
Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and / or the corresponding product(s).
DISCLAIME OF WA ANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below :
( ) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassembly, repair or modification of the product by the user.
(4) Inconvenience or any loss when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, when combined with third party devices.
(6) Any claim or action for damages, brought by any person or organization, due to a violation of privacy when
the surveillance footage, for some reason, becomes public or is used for the purpose other than
surveillance.

3
1. P ODUCT OVE VIEW
Key Features
3.0 Mega pixel /2.8" SONY progressive scan CMOS image sensor for excellent image quality
2.8mm wide angle lens
3-axis design
Support for corridor view (in H.264)
Integrated motion detection with pre- and post-alarm image / video buffering
Supports CBR (Constant Bit Rate) and VBR (Variable Bit Rate) modes
Supports Tampering-Alarm
Controllable frame rate
Privacy Masking up to 8 areas
Built-in standard PoE (802.3af)
HTTPS support
Integrated E-Mail, FTP, DDNS and DHCP client
Specifications
CLASSIFICATION SPEC
General
CPU ARM 76JZF-S
TM ( 400 MHz, Instruction cache : 32kbyte,
data cache : 6kbyte, MMU )
Flash 2Gbit Flash Memory
SDRAM
2Gbit
DDR
3
Memory
Image Pickup
Image Sensor 3. Megapixel /2.8" SONY Progressive Scan CMOS Image Sensor
Total Pixels 2065(H) x 565(V) 3.23 Megapixel
Effective Pixels 2065(H) x 553(V) 3.2 Megapixel
S/N Ratio More than 50dB
Min. Illumination 0Lux (IR On)
IR Distance 65’
Day & Night IR cut filter
Lens 2.8mm fixed lens
Video
Video Compression H.264 High Profile @ Level 5.0 (2048 x 536), @ Level 4.
(Other resolutions), Motion JPEG
Resolutions Up to 2048 x 536
Frame Rate H.264 Up to 30fps with 2048 x 536
MJPEG Up to 30fps with VGA Resolution
Video Streaming
Support Multi Stream with H.264, MJPEG
Adjustable
Frame
Rate
VBR / CBR in H.264
Image Setting
Brightness, Contrast, Sharpness
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
DSS, Corridor-view (in H.264), Mirror / V-Flip, etc.
Backlight WDR
Shutter Speed /4 ~ /2000
Noise Reduction 2D / 3DNR
Network
Dynamic
IP
SPECO
DDNS
(Free
of
Charge)
Security
Password Protection
User Access Log
HTTPS Encryption

4
Supported Protocol HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP
System
Integration
Intelligent Video Motion detection 2 x 2 blocks
Alarm Trigger Motion Detection, Tampering Alarm
Firmware Upgrade Remote Upgrade via Network
Physical
Etc x Factory Reset Button
Memory Slot Save to Micro SD card with event mode and continuous mode
Power Source DC 2V / .5A, POE (Power Over Ethernet) : 802.3af
Power Consumption Max. 3.0W, Max. 5.0W with IR On
Net Weight 0 oz
Dimension(in) 5. 2(
∅
) x 3.03(H)
Environment Operating Temperature - 4F ~ 22F
Storage Temperature -4F ~ 40F
Specifications are subject to change without prior notice for improvement.
2. NAME AND FUNCTION OF EACH PA T
2.1 Package Contents
APPEA ANCE DESC IPTION
IP Camera x
Installation Guide x
Drilling Template x
Tapping screw (Ø4 x 30) x 3
Plastic anchor x 3
CD x

5
2.2 Name and Function
NO. ITEM DESC IPTION
Power Connector
DC 2V


 Caution : If O3FDP9 is powered by PoE, do not
plug in DC Jack with active DC power into
DC power connector.
Network and
POE Connector POE (Power over Ethernet) and LAN cable
SD Card Slot Up to SDXC, 32GB
Lens 2.8mm fixed lens
Illumination sensor Control IR LED by sensing light
IR LED Infrared Hi-power LED
3. INSTALLATION
3.1 How to Mount to Ceiling / Wall
Ceiling
1
2
4
5
6
Ceiling Tile
Drilling Template
Plastic anchor x 3
Camera Ass'y
Tapping screw (Ø4 x 30) x 3
Dome Cover Ass'y
Lock
5
4
3
6
2
1
3

6
Wall
① Select the place to install the camera.
② Place the Drilling template on the ceiling and drill the holes.
③ Fix the plastic anchors in the holes.
④ Fix the camera by tightening tapping screws.
⑤ Adjust the camera angle and attached the Dome Cover.
Note
Do not touch the lens while making adjustment.
Open Position: Side Cable Access:
Lock Position:
3.2 3-Axis Adjustment
① Panning 360˚
Slightly loosen Pan Bracket nut then
adjust pan of the camera and
tighten the Bracket nut.
② Tilt 75˚
Slightly loosen Tilt bolt then
adjust tilt of the camera and
tighten the bolt firmly.
③ Rotation 360˚
Slightly loosen Tilt bolt then adjust rotation of the camera and tighten the bolt firmly.
When installing the cameras using the side
cable access on the ceiling, please cut out a
side access hole portion.
Tapping screw
(Ø4 x 30) x 3
Plastic anchor
x 3
Lock
Dome Cover Ass'y
Drilling
Template
Camera Ass'y
Lock ( ) the Dome Cover by moving clock-
wise.
And open (
) the Dome Cover by
moving counter-clockwise.
Lock
Lock Unlock
Tilt 75°
Pan 360°
Rotate 360°

3.3 INSTALLATION EXAMPLE
3.3.1 Installation Example
3.3.2 Connecting to the Network
Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double c
lick to open up the web viewer.
LAN Switch
Loca
l Access
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
lick to open up the web viewer.
LAN Switch
Router Internet
Remote Access
l Access
E-Mail / FTP
7
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
Remote Access

8
3.3.3 Accessing the Camera or video server’s Homepage
) Open the browser and input network camera address in the address bar or double click the device in IP
Scanner.
2) Please input your user name and password when prompted.
3) Default user name is admin and password is 1234 .
4) The first time you login to the camera, you will be notified that a ActiveX control is required to be installed.
You need to allow the installation of ActiveX.
4. DIMENSIONS (mm)
Input your IP
address here