Speco O4D1 User manual

Quick Start Guide
4MP Vandal Dome Fixed Lens IP Camera
O4D1
Version 1.1.1

i
elcome
Thank you for purchasing this Network camera!
This manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.

ii
Important Safeguards and arnings
1 ．
．．
． Electrical safety
All installation and operation here should conform to local electrical safety codes.
se a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2．
．．
．Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage
and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor
failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance
work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the
lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened
with a small quantity of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:
Stained with dirt
se oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint
se oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center
outward. Change the cloth and wipe several times if it is not clean enough.

iii
arning
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco Technologies
reserves the right to modify these without notice and without incurring any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or
missing in the package.
Accessory Name Amount
Network Camera nit 1
Quick Start Guide 1
Installation Accessories Bag 1
CD
1

iv
Table of Contents
1 Physical Specifications ........................................................................................................ 1
1.1 Components ....................................................................................................................................... 1
1.2 Dimensions ................................................................................................................................................ 2
1.3 Alarm Setup............................................................................................................................................... 2
2 Device Installation .............................................................................................................. 5
2.1 Installation Steps....................................................................................................................................... 5
2.2 Micro SD Card Installation ........................................................................................................................ 7
3 IP Scanner ............................................................................................................................... 8
3.1 Overview ............................................................................................................................................ 8
3.2 Operation ........................................................................................................................................... 8
4 eb Operation ....................................................................................................................... 9
4.1 Login and Main Interface .................................................................................................. 9

1
1Physical Specifications
1.1 Components
Note:
The following figure is for reference only, which is used to indicate the components and the
functions.
Refer to the following figure for component structure. See Figure 1-1.
Figure 1-1 Component structure
Please refer to the following table for detailed information.
Port Port Name Note
Port 1 DC power jack Connect to DC 12V power
Port 2 Ethernet Port Connect to standard Ethernet cable.
Supports POE.
Port 3 Audio input port Input audio signal
Port 4 Audio output port Output audio signal to speaker
Port 5 I/O port Alarm signal input/output

2
See below for detailed information regarding the I/O.
Port
Name
Port
Sequence Port name Function Description
I/O Port
1 ALARM_IN1 Sensor input
2 ALARM_O T1 Relay output
3 ALARM_GND Connect ground
1.2 Dimensions
Please refer to the following figure for dimension information. The unit is in mm. See Figure1-2.
Figure1-2
1.3 Alarm Setup

Alarm input, output description:
Step 1 Connect alarm input device
Step 2
Connect alarm output device to the alarm output of
open collector circuit
which connects 10K resistor to 3.3V externally.
Step 3 Open the web
viewer and
is an alarm signal, the
alarm input device will generate high and low level
the
corresponding type to NO or NC
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.
Please refer to the following figure for alarm input information. See Figure
Alarm input: When the input signal is idle or grounded, the device ca
of the alarm input port. When the input signal is connec
logic “1”. When the input signal is grounded, the device collects logic “0”.
Please refer to the following figure for alarm output information. See Figure
Figure1-3
Alarm input, output description:
Step 1 Connect alarm input device
to the alarm input of the I/O cable.
Connect alarm output device to the alarm output of
the I/O cable. A
larm output is
which connects 10K resistor to 3.3V externally.
viewer and
set the alarm input and output
correspondingly. When there
alarm input device will generate high and low level
corresponding type to NO or NC
.
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.
Please refer to the following figure for alarm input information. See Figure
1-4.
Alarm input: When the input signal is idle or grounded, the device ca
n collect the different status
of the alarm input port. When the input signal is connec
ted to 3.3V or it is
idle, the device collects
logic “1”. When the input signal is grounded, the device collects logic “0”.
Figure 1-4
Please refer to the following figure for alarm output information. See Figure
1-
5
larm output is
an
correspondingly. When there
alarm input device will generate high and low level
signals. Set
Step 4 Set the alarm output. The alarm output is for the alarm output port of the device.
n collect the different status
idle, the device collects
5

4
When alarm output is OC, it needs to increase pull-up resistance externally to work normally;
output signal is high and low level. After external pull-up resistance is increased, the default of
output signal is high level, and it switches to low level when there is alarm output.
The working current of alarm output port is recommended as <= 10mA. The max current which is
used to drive the external circuit is 80mA and it is advised to add a relay if it is beyond the value.
Figure 1-5

5
2Device Installation
2.1 Installation Steps
Note:
Before installation, please make sure the installation surface can support a minimum of 3
times the weight of the camera
Figure 2-1 Device installation illustration
Step 1
se inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner
hex screws on enclosure.
Step 2
Put installation template on the designated surface where you will install the device (wall or
ceiling).
Step 3
Drill holes according to position of the holes on the installation template and then insert the
expansion bolts in the holes. Secure these three bolts firmly.
Note:
If user pulls out cable from top of installation surface, you must dig an exit hole on
installation surface according to the installation template.
If user pulls out cable from side of cable channel, it must go through the -shape channel on
dome pedestal, and take out cable from the side exit hole on pedestal.
Step 4

6
Adjust the device installation pedestal to the proper position and then pull cable through the exit
hole on Installation surface. Make direction of TOP sign same as it is on the installation template.
Line up the three screw holes in the device pedestal to the three plastic expansion bolt holes in
the installation position. Put the three self-tapping screws in the three plastic expansion bolts
firmly. Fix dome body on installation surface.
Step 5
Hold both sides of the rotation bracket bottom with hands, rotate horizontally along the axis, and
adjust lens horizontal direction to designated position. Hold the LED decoration cover with hand,
rotate along the vertical direction, adjust the lens vertical direction to designated position; it is
okay to loosen the fix screws on both sides of the bracket first if it is too tight to adjust (just make
it loose, do not take it out), then adjust the lens, tighten the fix screws after adjustment. Hold the
LED decoration cover with hands, rotate horizontally along the axis, and adjust the lens image to
designated position. Range of lens: vertical (0° ～ +64°), horizontal (0° ～ +355°), image rotation
direction (0° ～ +355°).
Note:
When tilted to 64° vertically, please make sure to set the image rotation correctly in order to
avoid the outer cover blocking the IR light which would result in IR reflection.
Figure 2-2
Note:
Long press the “Reset button” shown in Figure 2-2 for 10 seconds when the device is
powered on if the device needs to be restored to the factory default setting.
Step 6
Take up the dome enclosure, put it back on the camera properly regarding to screw and hole, and
fasten the three inner hex screws with the wrench.

7
2.2 Micro SD Card Installation
Note:
Please disconnect the device before installing the micro SD card.
Step 1
Find the micro SD card slot in figure 2-2; open the slot according to the direction in figure 2-3.
Step 2
Adjust the card to the proper direction and install it into the slot.
Step 3
According to the direction in figure 2-4, close the micro SD card slot and keep it locked.
Figure 2-3 Micro SD Card installation illustration 1
Figure 2-4 Micro SD Card installation illustration 2

3IP Scanner
3.1 Overview
IP Scanner can search for the device on the local network.
Please note
that only devices that are on the same subnet can be discovered.
3.2 Operation
Open up IP Scanner.
Figure 3-1
In the device list, you can view the IP address, model number, and MAC address of each device.
Select the applicable device and double click to open
IP Scanner can search for the device on the local network.
that only devices that are on the same subnet can be discovered.
In the device list, you can view the IP address, model number, and MAC address of each device.
Select the applicable device and double click to open
up the web viewer.
Figure 3-1 IP Scanner
In the device list, you can view the IP address, model number, and MAC address of each device.

4eb Operation
This device supports viewing and management via a web browser on a PC.
4.1
Login and Main Interface
Open the browser and input network camera address in the address bar or double click the
device in IP Scanner. See
Figure 4
The login interface is shown as below. See
Please input your user name and password.
Default user name is admin
and password is
N
ote: For security purposes, please change the password after initial login.
After logging in, follow directions to install applicable plugins.
This device supports viewing and management via a web browser on a PC.
Login and Main Interface
Open the browser and input network camera address in the address bar or double click the
Figure 4
- 1.
Figure 4- 1 IP address
The login interface is shown as below. See
Figure 4- 2.
Please input your user name and password.
and password is
1234 .
ote: For security purposes, please change the password after initial login.
Figure 4- 2 Web login
After logging in, follow directions to install applicable plugins.
Open the browser and input network camera address in the address bar or double click the
ote: For security purposes, please change the password after initial login.
Input your IP
address here