Speco HTBIR1M User manual

INSTRUCTION
MANUAL
2MP TVI 940nm Black IR LED
Motorized Zoom Focus Camera
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice and without incurring any obligation. Rev. 08/01/2018
HTBIR1M
(Bullet Camera)
123624.indd 1 2018-08-21 오전 11:39:19

Contents
- 2 -
◑
Contents...................................................... 2
◑
Precautions ................................................. 3, 4
◑
Safety Instructions ...................................... 5
◑
Package Contents....................................... 6
◑
Camera Installation ..................................... 7-8
◑
Lens Adjustment ......................................... 9
◑
Specications.............................................. 10
◑
Camera Dimension ..................................... 11
◑
Features...................................................... 12
◑
OSD Menu Details ...................................... 13- 27
◑
Trouble Shooting......................................... 28
123624.indd 2 2018-08-21 오전 11:39:20

- 3 -
Precautions
Do not install the camera in
extreme temperature conditions.
Do not touch the front lens of the
camera.
Never keep the camera pointed
directly at strong light.
Do not expose the camera to
radioactivity.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or subject
it to physical shocks.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially careful to
provide ventilation when operating under
high temperatures.
This is one of the most important parts of
the camera. Be careful not to leave
fingerprints on the lens cover.
It can cause malfunctions to occur. If exposed to radioactivity the CCD
will fail.
Severe lighting change or flicker can
cause the camera to work improperly.
Housing damage can compromise
weatherproof ratings.
NOTE
* If the camera is exposed to spotlight or object reflecting strong light,
smear or blooming may occur.
* please check that the power satisfies the normal specification before
connecting the camera.
123624.indd 3 2018-08-21 오전 11:39:23

- 4 -
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION : To prevent electric shock and risk of fire hazards:
ō Do NOT use power sources other than those specified.
WARNING - To prevent electric shock and risk of fire hazards:
୛Do NOT use power sources other than that specified.
୛Do NOT expose this appliance to rain or moisture.
In USA and Canada, Use Class 2 Power Supply Only
123624.indd 4 2018-08-21 오전 11:39:26

- 5 -
Safety Instructions
Precautions for use
Please handle this camera carefully :
◑ This camera should be installed by qualied personnel only
◑There are no user serviceable parts inside
◑Do not disassemble this camera other than to make initial adjustments
◑Use a UL approved regulated 24 volt AC or 12 volt DC power supply
◑
Use appropriate low voltage power cable to prevent re or electrical shock
◑
Please insure that your installation area can support the weight of the camera
◑Do not use a strong or abrasive detergent when cleaning the camera
◑Do not install near cooling or heating device
123624.indd 5 2018-08-21 오전 11:39:26

- 6 -
Package Contents
Please make sure that the following items are included in the Package:
1) HTBIR1M
• 1 Video Test Connector, Power Jack
• 1 Bracket Base
• 1 Wrench
• Set Screw
- 4 Tapping Screws 4x25
- 4 Hexagon Socket Screws M5x10
- 4 Plastic Anchor
123624.indd 6 2018-08-21 오전 11:39:26

- 7 -
CAMERA INSTALLATION
6
CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 500mA)
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
3. CONNECT VIDEO CABLE
1) WHEN USING IT AS ANALOG OUTPUT,
CONNECT YELLOW COLOR BNC CABLE TO THE BNC JACK.
2) WHEN USING IT AS TVI OUTPUT,
CONNECT BLACK COLOR BNC CABLE TO THE BNC JACK.
DC 12V Power Supply
Power In put :R ED
Center : (+)
C V B S
T V I
LBACK:(-)
RED(+)
4. CONNECT RS-485 CABLE
- CONNECT 2 WIRE CABLE TO THE 485 PORT AS BELOW.
ORANGE (+)
WHITE (-)
Power Supply
AC 24V
123624.indd 7 2018-08-21 오전 11:39:26

- 8 -
CAMERA INSTALLATION
Compatibility
1) HTBIR1M
INTCM
SCREW-TAP, WHT,-,TH_M4X25,TP1, 4EA
SCREW-MS HEX,BLK,SUS,M5X10, 4EA
JUNCTION BOX
WALL
123624.indd 8 2018-08-21 오전 11:39:28

- 9 -
1) HTBIR1M
LENS ADJUSTMENT
VIDEO TEST
SET UP
LED LEVEL
Open the cap
123624.indd 9 2018-08-21 오전 11:39:28

- 10 -
1/2.9 Inch SONY 2Mega CMOS Sensor
2001 (H) X 1121 (V)
1985 (H) X 1105 (V)
1920X1080(1080p@30f / 1080p@25f)
1280X720_CROP(720p@60f / 720p@50f)
1280X720_CROP(720p@30f / 720p@25f)
Progressive Scan
50 dB
1.0Vp-p Composite. 75 Ohms / 1.0Vp-p TVI(Transport Video Interface) 75 Ohms
0.001 Lux @ F1.4(Sens-Up X32)
AUTO / Manual(1/25,1/30Sec ~ 1/30000Sec) / FLICKER
0
0
ON / OFF (Low,Middle,High) (15 Fram)
O(OFF/LOW/MIDDLE/HIGH)
Auto / Intensifier
AUTO/AWB/AWC-SET/MANUAL
0
x2 ~ x32
ON / OFF (4 Area)
3DNR (OFF/LOW/MIDDLE/HIGH)
O (AUTO/MANUAL)
0 ~ 20
0~20(Level Adjustable)
ON / OFF (16 Area)
MIRROR,V-FLIP
Image Sensor
Pixels - total
Pixels - Effective
Resolution
Scanning System
S/N Ratio
Video Output
Minimum Illumination
Shutter Speed
BLC
HSBLC
WDR(Wide Dynamic Range)
ACE(D-WDR)
(Adaptive Contrast Enhancement)
Day&Night
White Balance
Smart-IR
Sense-Up
Motion
Digital Noise Reduction
De-Fog
brightness
AGC
Privacy
Mirror
0~20(Level Adjustable)Sharpness
AUTO DETECTDefect
0Coaxial Communication (UTC)
ENG/KOR/CHN/CHA(S)/JPNLanguage
DUALPower
DC 12V - 600mA±10% AC 24V - 300mA±10% MaxPower Consumption
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Operating Temperature
-4ºF ~ +140ºF(Humidity : 20%RH ~ 95%RH)Storage Temperature
IUCJS2N
SPECIFICATIONS
HTBIR1M (2.8-12mm)
■
2MP TVI 940nm Black IR LED Motorized Zoom Focus Camera with included Junction Box
2.8-12mm MFZ Lens
123624.indd 10 2018-08-21 오전 11:39:29

- 11 -
CAMERA DIMENSION
1) HTBIR1M
3.90” 8.56”
4.80”
2.95”
3.01”
123624.indd 11 2018-08-21 오전 11:39:30

- 12 -
General Features
●
Transfer Video Interface
The combination of a 2Mega CMOS image sensor and TVI DSP provides an excellent resolution
of TVI picture.
●
3D-DNR
Smart 3DNR prevents the image blurring of moving object and activates only if moving objects
are appearing on the scene.
●
Smart-IR
No saturation image, vivid image in darkness! "TVI" camera makes very sharp video image in
darkness! This technology eliminates saturation of video image of the closer object in darkness
by control of the IR sensitivity. Saturation never happens in our "TVI"cameras, you can enjoy
vivid image in any dark condition!
●
Sens-Up
Despite a limited & low light condition, Sens-Up - Max. x32 helps the viewer to get visible and
clear images.
●
Defog
Defog function “improves” the clarity of images taken in poor conditions such as fog, smoke,
rain or snow.
●
WDR(Only For TVI Output)
A powerful and advanced technology that captures a high resolution picture even where
images appear dark.
●
CVBS(Composite Video Blanking and Sync)
TV system is switchable 'NTSC' or 'PAL' with built-in OSD.
●
Intelligent Function
An extraordinary technology that enables Speco Technologies TVI to become the ultimate
solution by providing intelligent features based on motion detection. It also strengthens crime
prevention and detection.
123624.indd 12 2018-08-21 오전 11:39:30

- 13 -
How to Set Up the camera menu
1. PRESET INDOOR, OUTDOOR, LOWLIGHT, HALLWAY, LOOBY(WDR), ELEVATOR
2. MAIN SETUP
3. EXIT EXIT / RESET(L/R-PUSHING)
MAIN SETUP SUB MENU 1 SUB MENU 2 SUB MENU 3 SUB MENU 4
1. 2MOTOR AF MODE AUTO / MANUAL
SCANNING HALF / FULL
ONE PUSH AF ON
SYNC TDN ON / OFF
INITIAL ON
RETURN
2. EXPOSURE BRIGHTNESS 0~20
AUTO
SUTTER MANUAL SPEED 1/30 ~ 1/30000
RETURN
FLICKER
INTENSIFY OFF ~ X32
AGC 0~20
RETURN
3. WHITE BAL AUTO
AWB
AWC-SET
MANUAL KELVIN LOW / MIDDLE / HIGH
R-GAIN 0~20
B-GAIN 0~20
RETURN
4. BACKLIGHT OFF
HLC LEVEL 0~20
MODE ALL DAY / NIGHT ONLY
RETURN
BLC H-POS 0~20
V-POS 0~19
H-SIZE 0~20
V-SIZE 0~19
RETURN
WDR WEIGHT LOW / MIDDLE / HIGH
RETURN
5. SPECO DNR OFF / LOW / MIDDLE / HIGH
6. DAY&NIGHT AUTO SMART IR 0~20
AGC THRES 0~20
AGC MARGIN 0~20
DELAY LOW / MIDDLE / HIGH
RETURN
COLOR
B/W SMART IR 0~20
RETURN
EXTERN SMART IR 0~20
EXTERN SW LOW / HIGH
DELAY LOW / MIDDLE / HIGH
RETURN
●
Setup Menu
MENU
123624.indd 13 2018-08-21 오전 11:39:30

- 14 -
7. IMAGE SHARPNESS 0~20
GAMMA 0.45 ~ 0.65
COLOR GAIN 0~20
MIRROR ON / OFF
FLIP ON / OFF
ACE OFF / LOW / MIDDLE / HIGH
DEFOG OFF
ON MODE AUTO / MANUL
LEVEL LOW / MIDDLE / HIGH
RETURN
PRIVACY OFF
ON ZONE NUM 0~15
ZONE DISP ON / OFF
H-POS 0~60
V-POS 0~34
H-SIZE 0~60
V-SIZE 0~34
Y LEVEL 0~20
CR LEVEL 0~20
CB LEVEL 0~20
RETURN
RETURN
9. SYSTEM COM. CAM ID 0~255
BAUDRATE 2400 / 4800 / 9600 / 57600 / 115200
RETURN
IMAGE RANGE FULL
COMP
USER OFFSET 0~32
RETURN
FRAME RATE 1080_30P, 720_30P, 720_60P
COLOR SPACE YUV / SD-CBCR / HD-CBCR
CVBS PAL / NTSC
LANGUAGE ENG / CHN / CHN(S) / JPN / KOR
COLOR BAR OFF/ON
RESET OFF/ON
RETURN ON
10. RETURN
8. MOTION OFF
ON
SENSITIVITY 0~10
WINDOW TONE 0~4
WINDOW ZONE 0~3
WINDOW USE OFF/ON
DET H-POS 1~60
DET V-POS 1~34
DET H-SIZE 1~60
DET V-SIZE 1~34
ALARM OFF/ON
RETURN
How to Set Up the camera menu
●
Setup Menu
MENU
123624.indd 14 2018-08-21 오전 11:39:30

- 15 -
2. Move and select the required function using the Up and Down button.
* Move the triangular indicator Up or Down to select the desired feature by pressing
the Up or Down button.
Menu Set Up
Menu items can be selected by using the OSD buttons of the camera.
1. PRESET
1-1. Preset : INDOOR / OUTDOOR / LOW LIGHT / HALLWAY / LOBBY(WDR) / ELEVATOR.
- Used for a quick and easy setup for the installation environment.
* The Advaned Set Up menu will be displayed on the monitor.
SPECO TECH
1. PRESET
2.MAIN SETUP
3.EXIT
INDOOR
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.RETURN
AUTO
AUTO
OFF
MIDDLE
AUTO
ON
123624.indd 15 2018-08-21 오전 11:39:31

- 16 -
3. Change menu settings using the Left or Right button.
* Available values or Status are displayed by pressing the Left or Right buttons.
Press the button until desired value / status is displayed.
4. After Changing the setting move the arrow indicator to EXIT and press the
SET button to EXIT.
NOTE
* Move to the available submenu by moving arrow to desired feature.
* Submenu is not available when this symbol displayed “---“.
1. Move the triangular indicator to 2MOTOR using the Up and Down buttons on the Set Up menu
screen.
2. Select the desired lens type by pressing the Left of Right button.
2MOTOR
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.RETURN
AUTO
AUTO
OFF
MIDDLE
AUTO
ON
123624.indd 16 2018-08-21 오전 11:39:31

- 17 -
◆ AF MODE
- AUTO : Adjust zoom and focus automatically.
- MANUAL : Adjust zoom and focus manually.
◆ SCANNING : HALF / FULL
- HALF : Adjust auto focusing when lens focus fixed. If lens focus is not fixed well, adjust focus manually.
- FULL : Scanning full size of scree and adjust autofocusing.
◆ ONEPUSHAF : If you press OSD button 3~4 seconds, focus will be fixed automatically.
◆ INITIAL : If you press OSD button 3~4 seconds, Lens Initializing start.
1. On the Set Up menu, Select EXPOSURE by using the Up or Down button.
EXPOSURE
1. 2MOTOR
AF MODE
SCANNING
ONEPUSHAF
SYNC TDN
INITIAL
RETURN
AUTO
HALF
ON
ON
ON
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.RETURN
AUTO
OFF
MIDDLE
AUTO
ON
123624.indd 17 2018-08-21 오전 11:39:32

- 18 -
2. Select the desired shutter mode by pressing the Left or Right button.
2. EXPOSURE
BRIGHTNESS
SHUTTER
INTENSIFY
AGC
RETURN
9 IIIIIIIIIIIIIIIIIII|
AUTO
X16
20 IIIIIIIIIIIIIIIIIII|
◆ BRIGHTNESS : The brightness can be adjusted. The brightness control range is 1~20.
◆ SHUTTER : DC lens is launched with the setting of 1/30 and the manual lens is launched
with the setting of Auto shutter, but the shutter speed can be adjusted from 1/30 to 1/30,000.
→ FLK : Select FLK mode if flickering occurs ; caused by the unmatched frequency of electric light.
◆ INTENSIFY : The bright screen can be displayed by sensing the degree of the darkness automatically
under the circumstance of low light condition or at night.
→ Off ~x32 Level Adjustable.
◆ AGC (Auto Gain Control) : The higher the AGC level is, the more noises appear.
→ 0~20 Level selectable.
NOTE
* INTENSIFY mode is not worked when Electronic shutter is selected as Manual.
123624.indd 18 2018-08-21 오전 11:39:32

- 19 -
White Balance
Use this function when the color adjustment of a screen is needed.
1. Move the triangular indicator to WHITE BAL on the SETUP menu screen using the Up and Down button.
2. Select the desired mode by using the left or Right button.
MANUAL
KELVIN
R-GAIN
B-GAIN
RETURN
MIDDLE
10 IIIIIIIIIIIIIIIIIII|
10 IIIIIIIIIIIIIIIIIII|
◆ AUT0 : Use this mode when the color temperature is from 2,500k to 9,500k.
◆ AWB : The function to search for the color which is matched well with the ambient environment.
◆ AWC→SET : After letting camera focus on the blank white paper to the best condition of current
lighting environment, press the SET button. If the lighting condition is changed, Re-adjustment
should be needed.
◆ MANUAL : Manual compensation make the more detailed control possible. First, after adjusting the
white balance using the ATW or AWB mode, change the mode into the manual compensation mode
and then press Set button. While looking at the color change of the subject seen on the screen after
setting up the proper color temperature, increase the each value of the blue and the red.
- KELVIN : LOW/MIDDLE/HIGH level adjustable.
- R-GAIN : 0~20 level adjustable.
- B-GAIN : 0~20 level adjustable.
- Return : Every function is set up at the EXPOSURE menu, and then return the previous menu.
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.RETURN
AUTO
OFF
MIDDLE
AUTO
ON
123624.indd 19 2018-08-21 오전 11:39:32

- 20 -
NOTE
The White Balance may not be worked properly in the following conditions. If this doesn’t
work, use the AWB mode.
* When there is a very high color temperature in the circumstances of the subject.
( for example, clear sky, Sunset)
*▶It is very dark.
*▶If the camera is headed to the fluorescent light directly or if there is a drastic lighting
change, The operation of White balance may become unstable.
BACKLIGHT
On this menu, backlight image can be compensated by users selecting one of modes. (HLC, BLC, WDR)
1. Move the triangular indicator to BACKLIGHT on the SETUP menu screen using the Up and Down button.
2. Select the desired mode by using the left or Right button.
MENU
1.2MOTOR
2.EXPOSURE
3.WHITE BAL
4.BACKLIGHT
5.SPECO DNR
6.DAY&NIGHT
7.IMAGE
8.MOTION
9.SYSTEM
10.RETURN
AUTO
OFF
MIDDLE
AUTO
ON
◆ Off : Deactivated status.
◆ HLC : This function is used to surpress or strong light source (for example, headlights of cars during
nighttime) so that other subjects can be seen in more detail. If you select HCL, a submenu appears
where you can make finer adjustments.
- LEVEL : Adjust the brightness level from which on the light source is to be masked out.
0~20 level adjustable.
- MODE : All day/night only adjustable.
123624.indd 20 2018-08-21 오전 11:39:33