Spirit Commercial CVC800 User manual

CVC800 Vertical Climber
OWNER’S MANUAL

Spirit Fitness

www.spirittness.com

2
Spirit Fitness
Congratulations on your new Vertical Climber and welcome to the Spirit Fitness family!
Thank you for your purchase of this quality Vertical Climber from Spirit Fitness. Your new Vertical
Climber was manufactured by one of the leading tness manufacturers in the world and is backed
by one of the most comprehensive warranties available. Through your dealer, Spirit Fitness will do all
we can to make your ownership experience as pleasant as possible for many years to come. If not
purchased direct from Spirit Fitness, the local dealership where you purchased this Vertical Climber is
your administrator for all Spirit Fitness warranty and service needs. Their responsibility is to provide
you with the technical knowledge and service personnel to make your experience more informed and
any difculties easier to remedy.
Please take a moment at this time to record the name of the dealer, their telephone number, and the
date of purchase below to make any future, needed contact easy. We appreciate your support and
we will always remember that you are the reason that we are in business.
Yours in Health,
Spirit Fitness

3
www.spirittness.com
RECORD YOUR SERIAL NUMBER
Please record the serial number of this tness product in the space provided below.
Serial Number:
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to Spirit Fitness. You can
also go to http://www.spirittness.com/warranty under the Support tab to register online.

4
Spirit Fitness
IMPORTANT SAFETY
INSTRUCTIONS
WARNING
When using an electrical appliance, basic
precautions should always be followed, including
the following: read all instructions before using this
appliance.
DANGER – To reduce the risk of electric shock:
always unplug this appliance from the electrical
outlet immediately after using and before cleaning.
WARNING – To reduce the risk of burns, re,
electric shock, or injury to persons, install the
Vertical Climber on a at level surface with access
to a 110-volt, 1.5-amp grounded outlet with only
the Vertical Climber plugged into the circuit.
DO NOT USE AN EXTENSION CORD UNLESS
IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END:
• Do not operate Vertical Climber on deeply padded,
plush or shag carpet. Damage to both carpet and
Vertical Climber may result.
• Keep children away from the Vertical Climber. There
are obvious pinch points and other caution areas that
can cause harm.
• Keep hands away from all moving parts.
• Never operate the Vertical Climber if it has a
damaged cord or plug. If the Vertical Climber is not
working properly, call your dealer.
• Keep the cord away from heated surfaces.
• Do not operate where aerosol spray products are
being used or where oxygen is being administered.
Sparks from the motor may ignite a highly gaseous
environment.
• Never drop or insert any object into any openings.
• Do not use outdoors.
• To disconnect, turn all controls to the off position,
then remove the plug from the outlet.
• Do not attempt to use your Vertical Climber for any
purpose other than for the purpose it is intended.
• The hand pulse sensors are not medical devices.
Their purpose is to provide you with an approximate
measurement in relation to your target heart rate. Use
of a chest transmitter strap (sold separately) is a much
more accurate method of heart rate analysis. Various
factors, including the user’s movement, may affect the
accuracy of heart rate readings. The pulse sensors

5
www.spirittness.com
your warranty. If you suspect the voltage is low,
contact your local power company or a licensed
electrician for proper testing. NEVER expose this
Vertical Climber to rain or moisture. This product
is NOT designed for use outdoors, near a pool
or spa, or in any other high humidity environment.
The operating temperature specication is 40 to
120 degrees Fahrenheit, and humidity is 95% non-
condensing (no water drops forming on surfaces).
Circuit Breakers: some circuit breakers used in
homes are not rated for high inrush currents that
can occur when a Vertical Climber is rst turned
on or even during use. If your Vertical Climber is
tripping the house circuit breaker (even though it
is the proper current rating) but the circuit breaker
on the Vertical Climber itself does not trip, you will
need to replace the home breaker with a high
inrush type. This is not a warranty defect. This is a
condition we as a manufacture have no ability to
control. This part is available through most electrical
supply stores. Examples: Grainger part # 1D237,
or available online at www.squared.com part
#QO120HM. The electrical outlet used should
have a dedicated 5-amp circuit breaker.
are intended only as exercise aids in determining
heart rate trends in general.
• Wear proper shoes. High heels, dress shoes, sandals
or bare feet are not suitable for use on your Vertical
Climber. Quality athletic shoes are recommended to
avoid leg fatigue.
• This appliance is not intended for use by persons with
reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have
been given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
• Keep children under the age of 13 away from
this machine.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
IMPORTANT ELECTRICAL
INSTRUCTIONS
WARNING
NEVER remove any cover without rst disconnecting
AC power. If voltage varies by ten percent (10%) or
more, the performance of your Vertical Climber may
be affected. Such conditions are not covered under

6
Spirit Fitness
GROUNDING INSTRUCTIONS
This product must be grounded. If the Vertical
Climber should malfunction or breakdown,
grounding provides a path of least resistance for
electric current, reducing the risk of electric shock.
This product is equipped with a cord having an
equipment-grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
DANGER - Improper connection of the equipment-
grounding conductor can result in a risk of electric
shock. Check with a qualied electrician or
serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify the
plug provided with the product if it will not t the
outlet; have a proper outlet installed by a qualied
electrician.
This product is for use on a nominal 110-volt/5-
amp dedicated circuit, and has a grounding
plug that looks like the plug illustrated below. A
temporary adapter that looks like the adapter
illustrated below may be used to connect this plug
to a 2-pole receptacle as shown below if a properly
grounded outlet is not available. The temporary
adapter should be used only until a properly
grounded outlet, (shown below) can be installed by
a qualied electrician. The green colored rigid ear-
lug, or the like, extending from the adapter, must be
connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is
used, it must be held in place by a metal screw.
IMPORTANT OPERATION
INSTRUCTIONS
• NEVER operate this Vertical Climber without reading
and completely understanding the results of any
operational change you request from the computer.
• Understand that changes in resistance do not occur

7
www.spirittness.com
immediately. Set your desired resistance level on the computer console and release the adjustment button. The
computer will obey the command gradually.
• Use caution while participating in other activities while pedaling on your Vertical Climber; such as watching
television, reading, etc. These distractions may cause you to lose balance which may result in serious injury.
• Do not use excessive pressure on console control buttons. They are precision set to function properly with little
nger pressure.
WARNING
This product can expose you to chemicals including Toluene and Acrylamide which are known to the State
of California to cause Cancer and birth defects or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov

8
Spirit Fitness
PRE-ASSEMBLY
UNPACKING
1. Cut the straps, then lift the box over the unit and unpack.
2. Carefully remove all parts from the carton and inspect for any
damage or missing parts. If parts are damaged or missing, contact
your dealer immediately.
3. Locate the hardware package. Remove the tools rst. Remove the
hardware for each step as needed to avoid confusion. The numbers
in the instructions that are in parenthesis (#) are the item number from
the assembly drawing for reference.
TOOLS INCLUDED:
13/14m/m_Wrench
12/14m/m_Wrench
Phillips Head Screw Driver
L Allen Wrench-M8
PARTS INCLUDED:
1 Main Frame
1 Console Mast
2 Console Mast Cover (Left and Right)
4 Handlebar Tubing
4 Levelers
1 Rear Stabilizer
1 Console
2 Foot Pedals
1 Power Cord
2 Transport Wheels
1 Water Bottle Holder
1 Hardware Kit

9
www.spirittness.com
STEP ZERO
1. Use L Allen Wrench (No.138) to
remove two 3/8”x3/4” Socket Head
Cap Bolts that hold the protective Side
Back (No.23) onto the mounting plate
on the Main Frame. Discard the bolts
and set the Side Back (No.23) aside.

10
Spirit Fitness
STEP ONE
HARDWARE FOR STEP 1
PART TYPE DESCRIPTION QTY
90 HEX HEAD BOLT 3/8” x 3/4” 2
93 HEX HEAD BOLT 3/8” x 3-3/4” 2
96 SOCKET HEAD CAP BOLT 3/8” x 3/4” 8
119 FLAT WASHER 3/8” x ø19 x 1.5T 8
125 CURVED WASHER 3/8” x 23 x 2.0T 4
126 SPLIT WASHER ø10 x 2T” 10
1. Attach Rear Stabilizer with Handle (No.12) to
mounting plate on the Main Frame (No.1) and secure
with 2 Hex Head Bolts (No.93), 2 Spring Washers
(No.126) and Curved Washers (No.125) by using
Wrench (No.135).
2. Pull the tie on the Console Mast (No.2) to have
Computer Cable (No.41) go through the mast from
bottom and out of the mast on top. Secure the Console
Mast (No.2) on the mounting plate on the Main Frame
(No.1) with four Socket Head Cap Bolts (No.96), 4
Split Washers (No.126) and 4 Flat Washers (No.119)
by using L Allen Wrench (No.138).
3. Secure the Console Mast Bracket (No.13) to the Main
Frame (No.1) using 4 Socket Head Cap Bolts (No.96),
4 Split Washers (No.126), and 4 Flat Washers
(No.119). Use 2 Hex Head Bolts (No.90) and 2
Curved Washers (No.125) to secure the Strap Hold
Down (No.2) to the Console Mast Bracket (No.13).

11
www.spirittness.com
STEP TWO
HARDWARE FOR STEP 2
PART TYPE DESCRIPTION QTY
88 HEX HEAD BOLT 5/16” x 15mm 2
121 FLAT WASHER 5/16” x 23 x 1.5T 2
90 HEX HEAD BOLT 3/8” x 3/4” 2
125 CURVED WASHER Ø3/8” x 23 x 2.0T 2
1. Take off the axle & screw from the Right Driving
Assembly (No.19), install lower hole of Right Driving
Assembly to axle of Connecting Arm (R)(#8) to
connect together, then rmly fasten one Hex Head Bolt
(No.88) through one Flat Washer (No.121) using the
Wrench (No.136).
2. Install into the upper hole of the Right Driving
Assembly to lower U shaped plate of Handgrip
Stabilizer Assembly (No.11), then insert the Axle into
upper hole through the lower U shaped plate, rmly
fasten with the previously removed screw using the
Wrench (No.136). Repeat for the left side.
3. Install the Mast Handlebar Assembly (No.14) onto
the Console Mast (No.2). Secure with 2 Hex Head
Bolts (No.90), 2 Curved Washers (No.125) using the
Wrench (No.135).

12
Spirit Fitness
STEP THREE
HARDWARE FOR STEP 3
PART TYPE DESCRIPTION QTY
91 HEX HEAD BOLT 3/8” X 2-1/4” 2
125 CURVED WASHER 3/8” X 23 X 2.0T 2
92 HEX HEAD BOLT 3/8” X UNC16 X 2-1/2 4
119 FLAT WASHER 3/8” x 19 x 1.5T 8
111 NYLON NUT 3/8” x 7T 4
1. Install the Seat Handle Bar (No.15L) onto upper
Handgrip Stabilizer Assembly (No.11), rmly fasten
one Hex Head Bolts (No.91) through one Curved
Washer (No.125) using the Wrench (No.135), and
rmly fasten 2 Hex Head Bolts (No.92) through 4 Flat
Washers (No.119), 2 Nylon Nuts (No.111) using the
Wrench (No.136). Repeat on the right side.

13
www.spirittness.com
STEP FOUR
HARDWARE FOR STEP 4
PART TYPE DESCRIPTION QTY
100 PHILIPS HEAD SCREW M5 X 10MM 18
102 SHEET METAL SCREW 3.5 x 12mm 6
1. Plug the Computer Cable (No.41) into Console
Assembly (No.40). Install the Console Assembly on top
of the mast of the Console Mast (No.2) (stuff rest cables
into the mast tube), then rmly fasten 4 Tapping Screw
(No.100) using the Screw Driver (No.137).
2. Install the Console Mast Cover (No.68L) & Console
Mast Cover (No.69R) to Chain Cover (No.70L) &
Chain Cover (No.71R), rmly fasten 4 Sheet Metal
Screw (No.102) using the Screw Driver (No.137).
3. Install one Handlebar Cover (No.79L) & one
Handlebar Cover (No.80R) onto upper left Handgrip
Stabilizer Assembly (No.11), rmly fasten 2 Tapping
Screw (No.100) & one Sheet Metal Screw (No.102)
using the Screw Driver (No.137). Repeat with the
Handlebar Cover (No.79L) & Handlebar Cover
(No.80R) & upper right Handgrip Stabilizer Assembly
(No.11).
4. Plug in the Oval End Caps (No.59) onto ends front
stabilizer tube of Main Frame (No.1).
5. Install the Track Slide Wheel Cover A (No.66) & the Track Slide Wheel Cover B (No.67) onto the upper left
Strap Hold Down (No.2) fastening with two Tapping Screws (No.100) using the Screw Driver (No.139). Repeat
with the other 3 sets to the lower left, upper right, and lower right of the Strap Hold Down (No.2).
6. Install the Beverage Holder (No.78) onto Strap Hold Down (No.2) using 2 Tapping Screws (No.100).

14
Spirit Fitness
CVC800 CONSOLE OPERATION

15
www.spirittness.com
Tablet Holder
Program Buttons
Start, Stop, Level
Up, Level Down,
and Enter
LCD Data Display
Window

16
Spirit Fitness
POWER
When the display is powered up, the all characters on the console will light up. The LCD Data Display
Window will show the software version and the total time the climber has been used since it was new.
After 3 seconds the console will go to the start-up display and your climber will be ready to use.
QUICK START
To begin working out in QUICK START mode, simply press the START key after the console has powered
up. In QUICK START mode, the TIME will count up from zero, and the workload/resistance may be
adjusted manually by pressing the UP/DOWN keys. Pressing the STOP key once will PAUSE the workout.
Press START to resume the workout. Press the STOP key twice to end the workout.
CONNECTING BLUETOOTH
The Bluetooth connection can be used for either pairing with your phone/tablet (APP) or with a wireless
Bluetooth chest strap (BLECHESTSTRAP). Please note that the default setting is for connection with APP. To
change the setting to pair with a Bluetooth chest strap, please follow the steps below.
• During the IDLE MODE, press the “ENTER” button for 2 seconds – you are now in SETTING MODE.
• Message in window will show “APP” – press either LEVEL UP or LEVEL DOWN to change between
“APP” and “BLECHESTSTRAP” – then press STOP/ENTER to return to IDLE MODE.
• The Bluetooth connection will now pair with a Bluetooth chest strap.
NOTE: If machine is powered off/on, the console will automatically revert to the default setting of
connecting to “APP” – to change to connect to “BLECHESTSTRAP” repeat steps above.

17
www.spirittness.com
MANUAL
The Manual program works as the name implies, manually. This means that you control the program
yourself and not the computer. To start the Manual program follow the instructions below.
1. Press the Manual key, then press the ENTER key.
2. Enter your age using the UP/DOWN keys, then press the ENTER key to accept the new number and
proceed.
3. Enter your weight using the UP/DOWN keys, then press ENTER to continue. This information is used to
help generate a more accurate caloric reading.
4. Enter the desired length of Time using the UP/DOWN keys, then press ENTER to continue.
5. You may now begin your workout by pressing the START key. To modify any of the settings, press the
STOP key to go back one step and repeat the steps above.
6. The program will start at level 1 to warm up. If you want to increase/decrease the workload simply
press the UP/DOWN keys.
7. During the Manual program you will be able to adjust the level manually by pressing the UP/DOWN
keys.
8. During the Manual program you may press the STOP key once to enter the PAUSE mode and press the
START key to resume the workout. Press the STOP key twice to exit the program.
9. When the program ends the display will show a summary of your workout. The summary will be
displayed for a short time, then the console will return to the start-up display.