SportsArt Fitness P826 User manual

P826 OWNER’S MANUAL CONTENTS
1. INTRODUCTION ................................................................................................................... 2
2. SAFETY PRECAUTIONS ...................................................................................................... 3
3.LIST OF PARTS ...................................................................................................................... 4
4. ASSEMBLE THE PRODUCT ................................................................................................ 9
STEP 1 Cover Support Plate and the Connector Installation ................................................... 9
STEP 2 Weight Stack Installation ............................................................................................ 13
STEP 3 Apply the Weight Stack Sticker ................................................................................... 17
STEP 4 Cover Support Plate and the Front Cover Installation ................................................ 18
STEP 5 Horizontal Beam and the Cable Installation ................................................................ 19
STEP 6 Cylindrical Cushion and the Lat Pull Bar Installation ................................................... 21
STEP 7 Seat Bottom Installation ............................................................................................... 22
STEP 8 Cable Adjustment ......................................................................................................... 23
STEP 9 Stack Fork Inspections ................................................................................................ 24
STEP 10 Rear Cover nstallation ............................................................................................... 25
STEP 11 Install plastic covern ................................................................................................... 26
STEP 12 Install cap nut ............................................................................................................ 27
STEP 13 Unit Inspection .......................................................................................................... 28
STEP 14 Secure the Product ................................................................................................... 29
STEP 15 Assistive Carabiner ................................................................................................... 30
5. OPERATION INSTRUCTION ............................................................................................... 31
OPERATION Safety Operating Area ....................................................................................... 31
OPERATION Exercising Instructions ........................................................................................ 32
6. MAINTENANCE ................................................................................................................... 34
MAINTENANCE Safety Precautions ....................................................................................... 34
MAINTENANCE Guide Rod Cleaning and Lubricating ............................................................ 35
MAINTENANCE Schedule ....................................................................................................... 36
MAINTENANCE Task List ....................................................................................................... 37
MAINTENANCE One-Year Maintenance Log .......................................................................... 38
7. CONSIGNES DE SÉCURITÉ IMPORTANTES .................................................................... 39
8. APPENDIXES ...................................................................................................................... 39
APPENDIXES Optional accessories ........................................................................................ 40
*We reserve the right to revise this manual at any time without notice.

2
1. INTRODUCTION
Congratulations on the purchase of a high quality SportsArt product, the P826 Lat Pull Down machine.
Constructed of high quality materials and designed for years of reliable performance, this product was made
for full commercial use.
Before this product is assembled or operated, we recommend that you familiarize yourself with this manual.
Understanding the correct assembly and operation of this product will help ensure that exercisers obtain
their tness goals safely and successfully.
1292mm(50.9 )
1134mm(44.6 )

3
2. SAFETY PRECAUTIONS
This product was designed and built for optimum safety. However certain precautions apply during the use
of this product. Please note the following safety precautions:
• Please read the entire manual before assembly and operation. Make sure the product is installed and
operated as instructed in this manual.
• Assemble and operate the product on a solid, level surface. Do not use outdoors or near water, including
pools and saunas.
• Check the product before every use. Make sure all parts are assembled, and all fasteners are tightened.
Do not use the product if it is disassembled in any way.
• Wear proper workout clothing. Do not wear loose clothing. Do not wear shoes with leather soles or high
heels. Tie all long hair back. Do not go barefoot on this product.
• Keep away from moving parts. Moving parts may or may not stop immediately if an object becomes
caught or impedes normal motion.
• Use this product only for its intended purpose as described in this manual.
• Be careful when mounting and dismounting the unit.
• Never operate this product if it has been damaged in any way. If it is not working properly, or has been
dropped or damaged, contact a service technician for repairs.
• Do not use accessories or parts that are not specifically recommended by the manufacturer (SportsArt).
Such parts might cause injuries or cause the unit to fail and void the warranty. We are not responsible for
any safety issue that arises due to the misuse of accessories or parts. At the same time, we will terminate
the warranty terms of this equipment.
• This product is not intended for use by persons (including children 12 or younger) with reduced physi-
cal, sensory, or mental capabilities, or by people who are otherwise deficient in product knowledge or
experience. If such people use this product, they should be given training and be supervised at all times
by someone responsible for their safety.
• Contact your SportsArt representatives on all materials damaged in shipment. (Note: Shipping damages
are the responsibility of the carrier.)
• Unpack and verify contents of boxes according to the list of parts to check if any parts are missing.
• Children 14 or younger should be supervised to ensure that they do not play on or near the product.
• The user weight limit for this product is 227 kg, 500 lb.
• Maintenance and repair must be performed by trained service personnel only. Improper maintenance
would not only damage the machine, but may also present a danger to the exerciser.
• Over exercise may result in serious injury or death
• Warning that any of the adjustment devices that could interfere with the user’s movement should not be
left projecting.
CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR WORKOUT and consult your
physician immediately. Work within your recommended exercise level. DO NOT work to exhaustion. Before
beginning any exercise program, you should consult with your doctor. It is recommended that you undergo
a complete physical examination.
*NOTE: Each machine provides a different resistance ratio of weight stack.

4
3. LIST OF PARTS
Box A
A2
A1
A6 A8
A7
A4 A5
A3
A14
A31
A12
A16
A17
A11
A15
A9-1
A9-2
A13
A32
A10

5
Box B
Box C + Box D
A21
A22
A20
A26
A24
A25
A23

6
Box A - Main Frame Components
No. Name Qty. No. Name Qty.
A1 Left/right perforated boards 2 A9-1 Anchor bracket of shroud
(square hole) 2
A2 Left/right side cover 2 A9-2 Anchor bracket of shroud
(tapped hole) 3
A3 Main frame 1 A10 Cover support plate A 2
A4 Cover support plate B-2 1 A11 Bracket 5
A5 Cover support plate B-1 1 A12 Anchor bracket 2
A6 Front cover A 1 A13 Top cover 1
A7 Stack fork 1 A14 Rear cover 1
A8 Weight stack rod 1 A15 Front cover 1
A16 Floor xing bracket 1
A17 U bracket 1
A31 Weight plate sticker
(10kg~60kg/22lb ~132lb) 1 A32 Weight plate sticker (65kg~100kg/143lb ~220lb) 1
Box B - User Frame Components
No. Name Qty. No. Name Qty.
A20 Horizontal beam 1 A24 Mast 1
A21 Cylindrical cushion 1 A25 Lat pull bar 1
A22 Seat bottom 1 A26 Carabiner 1
A23 Seat frame 1
Box C + Box D - Weight Plates Components
No. Name Qty. No. Name Qty.
A30 5kg/11lb weight plate 15

7
Components on the Product
No. Name Specication Notes
30
Hex head screw M10*P1.5*L30
Spring washer M10
Washer D16*d10.2*t1.0
31 Upper stack carriage set
32
Hex head screw M8*P1.25*L65
Flat washer D17*d8.3*t2
PU tube D12*d8*L51
Nylon hex lock nut M8
33 Guide rod
34
Round head inner hex screw M8*P1.25*L18
Spring washer M8*t2.0
Flat washer D17*d8*t1.5
35
Mushroom top inner hex screw M8*P1.25*L25
Flat washer D17*d8.3*t2
Nylon hex lock nut M8
Components in the Hardware Kit
No. Name Qty. Specication Notes
10 Screw socket 1 batch SGN-07
11 Mushroom top Phillips screw 10 M5*L15
12 Mushroom top Phillips screw 10 M5*0.8*L8
13
Hex head screw 6 M10*P1.5*L30
Spring washer 6 M10
Flat washer 12 D21*d10.5*t2
Nylon hex lock nut 6 M10
14 Mushroom top inner hex screw 10 M6*P1.0*L12
16 Phillips screw 6 M6*P1.0*L12
17 Flat washer 2 D27*d6.3*t3.0
Mushroom top inner hex screw 2 M5*L20
L-shaped Allen wrench 2 M4
L-shaped Allen wrench 1 M5
L-shaped Allen wrench 1 M6
Open end wrench 2 13*17
Phillips-head screw driver 1
21 Phillips pan head sheet metal screw 6 M4*L12
22 Phillips Umbrella head sheet metal screws 2 M4*L14
23 Round screw cap 2
59 Fastener 1 batch
Cap nut 1batch

8
Components on the Product
No. Name Specication Notes
36 Mushroom top inner hex screw M8*P1.25*L25
Spring washer M8
37 Beveled head inner hex screw M8*P1.25*L20
Nylon hex lock nut M8
38 Mushroom top Phillips screw M5*0.8*L15
Flat washer D13*d6*t1.0
46
Reinforcement plate
Anchor bracket
Umbrella hex screw M6*P1.0*L20
Plastic cover
47 Umbrella hex screw M6*P1.0*L12

9
4. ASSEMBLE THE PRODUCT
Follow instructions below to assemble this product. Note that in this manual the words “left” and
“right” are used to refer to the product and its parts. As such, these designations correspond to the
“left” and “right” sides of a person in position to exercise on this product. Also, for brevity, the word
“screws” or “nuts” is used where washers and other hardware may be involved.
STEP 1 Cover Support Plate and Connector Installation

10
STEP 1 Cover Support Plate & Connector Installation (CONT.)
Assemble the Main frame
(a). Remove the screw (30) locked under the Main frame (A3).
(b). Use the screw (30) to connect and lock the Seat frame (A23) and the Main frame (A3).
(b)
(a)
A3
A3
A23
30
30

11
STEP 1 Cover Support Plate & Connector Installation (CONT.)
Brackets and cover support plates installation
(a) Insert the screw sockets (10) into place in the main frame (A3) as shown, and then use
screws (11) to secure the brackets (A11) in place.
(a)
A11
A3
10
11

12
STEP 1 Cover Support Plate & Connector Installation (CONT.)
(b) Secure the plate slots (A10) to the straight frame of the weight stack tower (A3) with the
screws (12) and then cover the cap nuts (60). The plate slots (A4, A5) are secured to the left and
right side of the curved frame, respectively.
(Note: The plate slots have to be secured outside of the anchor brackets (A11).)
(b)
60
60
A4 A3
A10
A5

13
STEP 2 Weight Stack Installation

14
STEP 2 Weight Stack Installation (CONT.)
(a) Hold the upper stack carriage set (31), and then cut the zip tie. Gently lower the upper stack
carriage set (31) into place as shown.
(b) Remove screws (32). Set the guide rod (33) downward into place as shown.
(c) Tilt the guide rod (33) backward and then lift the upper stack carriage set (31) off the guide
rods as shown. Carefully set the upper stack carriage set (31) aside.
(a)
(b)
(c)
31
31
31
33
33
32

15
STEP 2 Weight Stack Installation (CONT.)
(d) Loosen and remove screws (34) from the stack fork (A7) and insert the weight stack rod (A8)
into the central mounting position of the upper stack carriage set (31). Use screws (34) to se-
cure the stack fork (A7) into place of the upper stack carriage set (31) as shown.
(Note: Remove the stack fork first before assembling.)
*Remove screws (97) from the set fork (98) to remove the bolt assy.crossover (99). Pull the cable
from the stack fork to thread through the bolt assy. crossover (99) as shown. Secure the bolt
assy. crossover(99) back into place of the set fork (98) with screws (97) as shown.
(e) Insert and lower the (5 kg/11lb) weight plates (A30) into place on the guide rods (33) one at a
time. Once complete, slide down the upper stack carriage set (31) on top of the weight stack.
(Note: The stack fork (A7) points toward the front.)
* If there is an optional (7.5kg/16.5lb) weight plate installed, insert the optional weight plates first
before the (5 kg/11lb) weight plates (A30).
*Install the cap nuts on the screws.
(d) (e)
A7
A7
A8
A30
34
34
31
31
A7
A8 31
60
97
97
98
99
99
60 M4/M5

16
STEP 2 Weight Stack Installation (CONT.)
(f) Tilt the guide rods (33) back into place and then lift them up to their mounting position, and
then secure the assembly with screws (32).
(f)
32
33
33
65 M8
65

17
STEP 3 Apply the Weight Stack Sticker
Note: Before applying weight plate stickers, please wipe the area clean, and clean your hands
before proceeding to the next step.
(a) Align and tape the cardboard to the upper left corner of the weight plate (A30).
(b) Peel off the top half of the weight sticker (A31) backing. Leave the clear outside margin in place
on the sticker. Don’t peel off the margin.
(c) Press the numbered part of the sticker in place while you peel off the clear margin of the sticker.
(d) Peel off the clear margin of the sticker.
(e) Follow steps (b) ~ (d) to apply the weight plate sticker (A32) to the lower part of the weight stack.
When the stickers are in place, peel off the card board. Press the sticker in place to ensure
good contact on the weight plate.
*If there are additional optional weight plates, use the optional weight plate stickers.
(a) (b)
(c)
(d)
(e)
A30
A31
A32

18
STEP 4 Cover Support Plate and the Front Cover Installation
(a) Install the square snap bushings (10) to the anchor brackets of shroud (square hole) (A9-1).
Secure the anchor brackets of shroud (square hole) (A9-1) with the square snap bushings
(10) to the front and back of the upper crossmember assembly of weight stack tower (A3) with
screws (14). Secure the anchor brackets of shroud (tapped hole) (A9-2) to the front and back
of the lower crossmember assembly of weight stack tower (A3) with screws (14).
(b) Slide the front cover (A15) from the top down into the cover support plates’ grooves.
(Note: Take out the stack fork (A7) and place it on the upper stack carriage set (31) as shown
to avoid damaging to the cover.
(c)Secure the lower shroud with the screw (46).
(a)
A9-1
A9-2
A9
A9
A7
A15
10
14
(c)
A15
46
46
14
(b)
A15

19
STEP 5 Horizontal Beam and the Cable Installation