SPRT SP-L36 User manual

SPRT®
SP-L36
Portable Thermal Printer
User’s Manual
( ver 0.04)
Beijing Spirit Technology Development Co., Ltd
www.sprt-printer.com
1

CONTENT
NOTICE........................................................................................................................ 1
Notice of Safety.................................................................................................... 1
Notice of Storing................................................................................................... 1
Chapter 1 Outer Appearance and Model No.......................................................... 2
1.1 Outer Appearance......................................................................................... 2
1.2 Model No.........................................................................................................2
Chapter 2 Characteristic Specification.....................................................................2
2.1 Printing Specification.................................................................................... 2
2.2 Physical Parameters..................................................................................... 3
2.3 Environment................................................................................................... 3
2.4 other Specification.........................................................................................3
Chapter 3 Operation Method.....................................................................................4
3.1 Using Preparation..........................................................................................4
3.1.1 Battery Installation...............................................................................4
3.1.2 Paper Roll Installation.........................................................................4
3.1.3 Others................................................................................................... 5
3.2 Basic function usage.....................................................................................5
3.2.1 Switch On............................................................................................. 5
3.2.2 Switch Off............................................................................................. 5
3.2.3 Self-Test............................................................................................... 5
3.2.4 Paper Feeding (Manual Feeding).....................................................6
3.2.5 Hexadecimal Printing..........................................................................6
3.2.6 Printer Parameters Setting................................................................ 6
3.2.7 Battery Charging................................................................................. 7
3.2.8 Enter program upgrade Mode........................................................... 7
3.3 Printer Parameters Settings.........................................................................8
3.4 Printer label sensor calibration.................................................................... 8
3.5 Restore the default configuration................................................................ 8
3.6 Printer Interface Connection and Printing..................................................9
3.6.1 USB Connection.................................................................................. 9
3.6.2 Bluetooth Connection......................................................................... 9
3.6.3 WiFi connection.................................................................................10
3.7 Buzzer........................................................................................................... 10
3.8 LCD indication..............................................................................................11
Chapter 4 Other Information................................................................................... 12
4.1 Command Programming Manual..............................................................12
4.2 Description of Black Mark Pre-print..........................................................12
4.3 Instruction on Label Paper.........................................................................13
Appendix A.................................................................................................................14
Appendix B.................................................................................................................16

1
Statement
This is grade A product, which may lead to wireless radio
interference. Under this circumstance, it may need users to apply
practical measures for this interference.
NOTICE
Please read this manual carefully before using the printer!
Notice of Safety
Be sure to use the specified battery and power supply provided by our company.
Otherwise it may cause fire, explosion or damage printer, meanwhile, the battery also may
be damaged.
Don’t put battery into the fire, don’t disassemble or heat the battery, don’t be short circuit,
it may cause fire, explosion or damage printer, meanwhile, the battery also may be
damaged.
If the printer would not be used for a long time, be sure to take off the battery, otherwise
the battery may leak liquid which is corrosive liquid, if improper operation causes battery
leak liquid, and it paste in the skin or clothes, please rinse it by clean water, if paste in the
eyes, please rinse them thoroughly by clean water and see a doctor. Please do not open
the paper case cover when it is printing or just when printing is finished, do not touch the
printer head with hand or body, overheat may cause scald.
Notice of Using
Pls do not print more than 1 meter receipt,or will cause damage to printer head .
Water or other liquid should not be spilled into the printer, also the printer should not be
appeared in the rain, or else may cause printer damage. Please do not open the paper
case cover when it is printing, otherwise the printer may work improperly. If printer is using
USB connection to work, should not unplug the USB cable, or else some printing data
may be lost. When printer is using Bluetooth connection to work, the distance of
communication should be within 10 meters, otherwise the printer doesn’t print or prints
rubbish codes.
Too high（45℃）or too low（0℃） environment temperature and too high (85％) or too low
(20％) environment humidity both effect the printing quality.
The printer paper roll with poor quality or stored for too long time also may reduce the
printing quality even damage the printer.
Under the black mark detecting mode, the printer requires that the pre-printed black mark
is accordant with the printing rule of black mark (please refer to details in Chapter 4.2),
otherwise the black mark can not be detected correctly.
Pls do use the good label paper which is coincident with the requirements when the
printer work under the label paper mode (pls refer to details in Chapter 4.3), otherwise,
the printer may be not able to check the labels exactly.
Be sure to use up the power of the battery before charge up it,as it can ensure the using
life of the battery.
Notice of Storing
The printer should be placed in such an environment that the temperature is
between-20℃and 60℃, and the relative humidity is between 10% and 90%.
If the printer will be stored for a long time, please be sure to take out the battery, otherwise
may damage the battery and printer.

2
Chapter 1 Outer Appearance and Model No.
1.1 Outer Appearance
1.2 Model No.
Model
Interface
SP-L36BTDM
USB and Bluetooth
SP-L36W
USB and WiFi
Chapter 2 Characteristic Specification
2.1 Printing Specification
Printer Method: Thermal line
Paper Width: 79.5± 0.5mm, 57.5± 0.5mm
Effective Printing width:72mm,48mm
Resolution: 8 dots/mm (203dpi)
Dots in each line: 80mm: 576dots/line
58mm: 384dots/line
Printing Speed: thermal paper: 80mm/s (Max);
label paper: 60mm/s (Max)
Paper Thickness: 0.06-0.08mm (thermal paper);
0.06-0.15 (label paper)
Printable Content: GB18030 (Chinese), BIG5 (Traditional Chinese), GB12345
(Traditional Chinese) ，ShiftJIS Japanese Characters, ASCII characters,
self-defining characters, bitmaps.
1D Barcode: UPCA,UPCE,EAN13,EAN8,CODE39,ITF25,

3
CODABAR,CODE93,CODE128
2D Barcode: PDF417,QR CODE,DATA Matrix
2.2 Physical Parameters
Dimension: 123(L)X112(W)X67(H)mm
Physical Weight: 436g (excluding roll paper)
Paper Roll Diameter: ≤ 50.0mm
Interface: USB, Bluetooth, WiFi
2.3 Environment
Operating Temp: -20℃~50℃
Operating Humidity: 10%~80% ( relative humidity)
Storage Temp: -20℃~60℃
Storage Humidity: 10%~90% ( relative storage humidity)
2.4 other Specification
●Paper Loading Method: drop-in easy loading（please refer to details in
3.1.2 Paper Roll Installation).
●Paper Tearing Method: Manually tearing
●Black Mark Location: available(details please see 4.2 pre-printed black
mark manual).
●Printing Control Command: ESC/POS compatible command set/CPCL
command set. (Pls refer to the details in “The Commands Manual of SP-L36”).
●Power Supply: 7.4V/2100mAh rechargeable polymer lithium battery.
●Low Power Alarm: When the electric of battery will run out, the battery
icon in the printer screen will flash.
●Battery Charging: quick charging, it will be charged full about 4hours;
●Auto-sleeping: If the printer doesn’t receive any data or no any buttons
operation within 5seconds, the printer will go into the auto-sleeping mode.
During auto-sleeping, press any buttons on the printer or the printer receives
any data will call the printer on.
●Battery Duration: under25% printing density ,at least 200 meters, the
standby time is over 4days. These parameters are just for reference, long term
usage will cause the capacity decline, and can not ensure the time of printing.

4
Chapter 3 Operation Method
3.1 Using Preparation
3.1.1 Battery Installation
1. Put the battery into the battery slot from the side with pins and press the
other side into case.
2. Then tighten the M2.5*4 countersink screw (as below Pic.)
3.1.2 Paper Roll Installation
1. Press the OPEN button to open the paper case cover (as shown in Figure 1),
put your finger in the finger groove in the baffle, slide the paper roll baffle
outward till it is suitable for the width of the paper roll (as shown in Figure 2) .
2. Load the roll paper with the downward thermal face, pull out a part of paper
and put them in the middle of the paper out orifice. (The end of paper is
beyond the tear cutter.)
(see Figure 3).
3. Shut down paper case cover and cut off the redundant paper

5
3.1.3 Others
Instruction for opening or closing the paper case cover: Opening or
closing the paper case cover slowly after pressing the OPEN button.
Abnormal operation instructions: Paper blocking is not allowed at the
outlet.
Placement direction: Hold it flat and try to ensure the stability of running
paper roll when printing.
3.2 Basic function usage
Printing Modes: Standard Mode and Logistics Mode.
Paper Type: Thermal paper, Black mark paper and Label paper.
Logistics Modes: Way Bill mode, Receipt mode, Invoice mode. Label paper
( 80mm width ) as default under Way bill mode. Receipt paper ( 58mm width )
as default under Receipt mode. Black mark paper ( 58mm width ) as default
under Invoice model.
Standard Modes: 80mm mode, 58mm mode.
Standard thermal paper as default under Standard mode.
Printing modes or paper type can be set by Setting Tool (Way Bill mode and
Invoice mode can’t be changed under the logistics mode)
3.2.1 Switch On
Press the【POWER】button, you will hear ‘one low one high ’prompt tone.
“Loading...” will shown in LCD, then the printer turns into work mode when
loosen the【POWER】button. Printer parameters will also shown in the LCD.
3.2.2 Switch Off
Under status of switch on, the printer will send out the prompt tone of ‘one low
one high ’ after pressing the【POWER】button, the LCD turns off, then loosen
the【POWER】button, the printer switched off.
3.2.3 Self-Test
After receiving the printer, user can print the self test to check current settings
and status of the printer at anytime.
The printing way is as below: Power off, then hold down the 【FEED】button
and press the 【POWER】button. When you hear ‘one low one high ’prompt

6
tone and LCD shows “Loading...”, loosen 【POWER】button first and then
release 【FEED】, the self-test will be printed out.
3.2.4 Paper Feeding (Manual Feeding)
A. Standard Mode:
Under the normal work status and apply to thermal receipt paper, press
【FEED】button, the paper feeding begins, and stops when loosen 【FEED】
button. When the printer apply to black mark paper and label paper, press
【FEED】button, the printer begins to feed paper and stops over the position of
black mark/label spacing. If the paper is not the black mark/ label paper, the
printer stops automatically after feeds paper for 26cm, and alarms the error of
paper end for label paper.
B. Logistics Mode:
Under the normal work status and apply to receipt, press【FEED】button, the
paper feeding begins, and stops when loosen
【FEED】
button. When the printer
apply to invoice and waybill, press【FEED】button, the printer begins to feed
paper and stops over the position of black mark/label spacing. If the paper is
not the black mark/ label paper, the printer stops automatically after feeds
paper for 26cm. And alarm the error of paper end for waybill.
3.2.5 Hexadecimal Printing
The function of hexadecimal printing is to print the data which received from
host machine by hexadecimal numbers and corresponding characters. It will
be convenient to debug program.
Enter hexadecimal printing mode: Power off, hold down the【MODE】button
and press the
【POWER】
button at the same time. Then loosen the 【POWER】
button and press the 【FEED 】button when you hear ‘one low one high’
prompt tone of power on and LCD shows “Loading...". After that you may
loosen the 【MODE 】button and 【FEED 】button. The printer enter the
hexadecimal printing mode and print the notice.
Exit hexadecimal printing mode:The way to exit hexadecimal printing mode is
switch off the printer or press the 【FEED】button for three times. The printer
will also print the notice which shows that the printer have exit hexadecimal
printing mode.
3.2.6 Printer Parameters Setting
Some simple parameters of the printer can also be set by operating buttons.
There are two methods of entering parameter setting mode, which can set

7
different parameters.
A. Under the state of power off, hold down the 【MODE】button, then press
the【POWER】button. Loosen the【POWER】button first and then【MODE】
button when you hear ‘one low one high prompt tone and LCD shows
“Loading...”. The printer turns into the parameters setting mode. Press the
【FEED】button or 【MODE】button, LCD shows the first item which can be
set parameters and the current numerical value. Details refer to Appendix A.
Exit parameter setting: Hold down【MODE】and then【FEED】buttons, then
loosen【MODE】button and【FEED】button. Saving the set parameters and
exiting the parameter setting mode. The setting parameters won’t be saved if
you directly press the 【POWER】button to turn off the printer.
B. Under the state of standby, press the 【MODE】button above 2 seconds to
enter the parameter setting mode. Press the 【MODE 】button to select the
setting parameter items, and press the
【FEED】button to select the sub-menu
of parameter items. Details refer to Appendix B. After setting the parameters,
wait for 5 seconds, the printer will exit the parameter setting mode and save
the setting values automatically.
3.2.7 Battery Charging
The battery will run out after a period of usage. When it nearly runs out, printer
will give a alarm through the battery indicator flashing on LCD, at this time,
user needs to charge up the battery.
Charging method is as following: connecting the adapter to the power socket
with 220V, 50HZ, then plug the power charging plug to the power socket of the
printer, then the power charging begins. During the charging process, the LCD
screen of the printer will have a charging prompt.
In the power- off state: the icon shown with a plug image, and the battery
power indicator icon is continuously changing to indicate that it is charging.
Only one full battery icon is displayed to indicate that it is fully charged.
In the power-on state: the battery power indicator icon in the upper right corner
of LCD is continuously changing to indicate that it is charging. If the battery
power icon does not change, it indicates that it is fully charged.
3.2.8 Enter program upgrade Mode
a. Quick enter method
In the state of power-off, press both 【MODE】button and 【FEED】button.
When hearing the `one low one High' prompt sound, quickly release both
buttons, the printer enters the program upgrade mode. At this time, LCD
displays “ Upgrading”. Use "UpdateFirmware" (upgrade tool for PC) tool to
upgrade.
Note: Only USB interface supports quick enter method.

8
b. Upgrade in printing mode:
In the power-on state, the printer can support printing mode upgrade when
there is no error status. You can connect printer with PC by USB interface and
use the "UpdateFirmware" tool to upgrade. Or "SprtPrinterUpdateTools" can
be used (mobile upgrade tool). Connected by Bluetooth or WiFi to upgrade.
3.3 Printer Parameters Settings
Users can set more parameters by using the specified〈Setting Tool〉software
through computer. The setting includes: language, font, printing density,
default codepage, Bluetooth device name and password, printing mode etc.
The setting method please refer to the <Setting Tools Software Help> which
offered with the software together.
3.4 Printer label sensor calibration
Label sensor calibration is to adapt to different types of label paper on the
market. By adjusting the sensor configuration of the printer, the printer can
correctly position the label.
When it is currently in label paper mode, press the [MODE] key first, then
press and hold the [power] key, when you hear the power-on prompt, release
the [power] key, and then press the [FEED] key twice Times, then release
[MODE]. The printer enters label calibration mode. And print out "Sensor
calibration mode\r\nPlease press the paper key\r\n".
Power off directly to cancel the calibration.
After pressing the paper feed button, the printer will feed the paper for a fixed
length, and then print out the "maximum voltage value: xx.xV\r\n minimum
voltage value: xx.xV\r\n paper sensor setting value: xx". If the paper type is
incorrectly configured or the hardware cannot support the current paper, the
words "Automatic exit for wrong paper type setting" and "Automatic exit for
calibration error" will be printed separately.
3.5 Restore the default configuration
When the printer configuration item is incorrectly configured and cannot work
normally, use this function to restore the factory configuration content.
In the shutdown state, first press the [MODE] key, then press and hold the
[power] key, when you hear the power-on prompt and the LCD screen starts,
release the [power] key, then press the [FEED] key three times, and then
release Open
【MODE】
key. The printer enters the factory reset mode. And print
out the "Note: Set the recovery system to the default value, press the FEED
key once to confirm. Direct power off cancellation" prompt.
Direct power off to cancel recovery.
After pressing the paper feed button, the printer will print out the words
"Restore System Settings Successfully". After the recovery is complete, the