SPX FLOW Viking Power 32 User manual

INSTRUCTION MANUAL
ORIGINAL INSTRUCTIONS/TRANSLATION OF ORIGINAL INSTRUCTIONS
READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS
PRODUCT
Viking Power 32 & Viking Power Vacuum
12/24 V DC
IB-117 R05 (09/2017)

Typical applications
Viking Power 32/Vacuum is the ideal
diaphragm pump for toilet drain, wastewater
and bilge pumping. Its compact design gives
a very adaptable mounting and installation in
the boat. Viking Power Vacuum has a large
self-priming capability and is very suitable
for installation in a vacuum system.
Model number
Viking Power 32 12V 10-13373-03
Viking Power 32 24V 10-13373-04
Viking Power Vacuum 12V 10-13373-07
(double anti-drainback valves)
Viking Power Vacuum 24V 10-13373-08
(double anti-drainback valves)
Features
• 32 L/min at open flow – Viking Power 32
• 30 L/min at 0.1 bar pressure –
Viking Power 32
• 24 L/min at open flow – Viking Power
Vacuum
• 22 L/min at 0.1 bar pressure – Viking
Power Vacuum
• Compact design
• Connection: 1½” hose
• Quiet operation
• Self-priming to 2,5 m – Viking Power 32
• Self-priming to 5 m – Viking Power
Vacuum
• Pump head can be rotated 360°
• Dry running without damage
• No filter required
• Ball-bearing supported transmission
• Low power consumption (40W at 0.1 bar
pressure)
• Hand-cranked
• Meets ISO15083 (Small Craft Bilge
Pump standard for boats from 12 m/40 ft
Working principle
Single-chamber, self-priming diaphragm
pump. To obtain good self-priming ability
and a filter-less solution, the pump is
designed with a large single diaphragm
and a long stroke. This way a lot of water
is pushed through the pump house in each
stroke and any debris is flushed through
(compare rubber sink cleaner)
Technical description
Body: Nylon
Valves: Nitrile
Diaphragm: Reinforced Nitrile
Screws: Stainless steel
Stand: Painted galvanized steel
Connection: 1½” hose
Max. discharge
height: 4 m
Max. suction lift: 2,5 and 5 m
respectively (Viking Power Vacuum)
Max
discharge+ lift: 5 m
Motor: 40 W at 0.1 bar pressure
12/24V (with built-in
thermal protection)
Fuse size: 12A – 12V / 6 A – 24V
The pump is CE marked according to the
following standards:
• EN55014-1:2000/Radio disturbance
• ISO8846: Small Craft – Electrical devices
– Protection against ignition of surrounding
flammable gases
• ISO8849:2003/ Small craft – Electrically
operated bilge pumps
• ISO10133: 2001/Small Craft – Electrical
systems – Extra-low voltage DC installations
Drawing
See page 27
Pressure and Capacity data
Viking Power 32 /Viking Power Vacuum
mounted to DC motor 12/24 V
Please follow all instructions before attempting an installation.
7
Original instructions
> English

Pressure Flow Amp. draw
Bar kPa Psi L/min USGPM 12V 24V
0 0 0 34.4 9.1 2.5 1.2
0.1 10 1.5 30.8 8.1 3.3 1.6
0.2 20 2.9 27.1 7.2 4.2 2.1
0.3 30 4.4 23.5 6.2 5.0 2.5
0.4 40 5.8 20.0 5.3 5.6 2.8
0.5 50 7.2 16.7 4.4 6.1 3.1
Fuse required 12 A 6 A
Installation and maintenance
Installation
• Mount the pump in a dry location.
• If the pump is mounted vertically, the
motor must be above the pump house.
• Mark screw positions and drill pilot
holes.
• Mount the pump using stainless steel
screws and the enclosed washers. Make
sure that the plastic spacers are in their
correct position. NOTE: Take care not
to fasten the vibration-damping rubber
feet too much.
• Mount the outlet anti-drainback valves
and screw the connections - Viking
Power Vacuum.
NOTE: The anti-drainback valves are
mounted with the pointed end towards
the flow direction. See the drawing.
• Reinforced flexible tubing is recom-
mended.
• Use stainless steel hose clamps to secure
tubing to connections and other hose
barbs in the system.
Electrical installation
The pump must be installed according to
ISO 10133 (Small craft – Electrical system
– Extra low voltage DC installation).
NOTE: The fuse must be ignition protected.
The motor is equipped with built-in thermal
protection to prevent overheating. The
protection is automatically restored when
the motor is cooled. See the wiring diagram
for correct installation. Negative wire must
be black.
Choose wire size in accordance with total
wire length (see table). The wire connections
must be sealed with a marine sealant.
NOTE: Before installation with electrical
control systems, check that equipment to be
used is of sufficient rated capacity to accept
amperage draw of motor. Low voltage can
cause the motor to overheat.
Maintenance
The pump valves inside the pump house
should be regularly cleared from debris to
prevent reduced performance and poor
self priming capability. This is done by
unscrewing the house clamp and opening
the house. The outlet
anti-drainback valves are located
above the connections. (Viking Power
Vacuum.) NOTE: Make sure the pump is
disconnected from the power supply.
Wiring diagram
Other electrical devices such as circuit breaker
and relays must be installed between the pulp
and the positive (+) lead on the battery (on the
red wire).
Pump
Terminal
fuse
Max 0.2 m
Red
Black
+
–
Wiring dimensions
(Based on 10% voltage drop)
Wire size Max wire length* in m
12V 24V
1.5 mm² #16 AWG 18 71
2.5 mm² #14 AWG 30 118
* The wire length is the total distance from the
battery to the pump and back to the battery. It is
recommended to use a relay with a light wire from
the main cable to shorten the main leaders.
8
Original instructions
> English

Self-priming
The pump is self-priming up to 2,5 and 5 m
respectively (Viking Power Vacuum)
Dry running
The pump can be run dry without any harm.
It will however unnecessary reduce your
battery power.
Hand cranked power
The pump can in case of
emergency such as power
failure be run with the enclosed
hand-cranked power source.
NOTE: Make sure that the
pump is disconnected from the
power supply while the motor is working
as a power generator.
NOTE: Do not run the pump with power
supply and the crank mounted at the same
time.
Winterizing
Drain the pump from water by pumping
it until it primes air and there is no fluid
coming from the outlet.
Service instructions
Change of diaphragm
1. Remove the two screws that hold the
clamps and remove the clamps.
2. Remove the pump housing.
3. Remove the screw that holds the
diaphragm and the diaphragm washer.
4. Remove the diaphragm and the
diaphragm washer.
5. Mount the new diaphragm and the new
diaphragm washer with the new screw.
6. Assemble the pump housing and the
clamps.
Change of pump housing
1. Remove the two screws that hold the
clamps and remove the clamps.
2. Remove the pump housing.
3. Assemble the new pump housing and
the clamps.
Cleaning the anti-drainback valve(s)
1. Remove the two screws that hold the
clamps and remove the clamps.
2. Remove the pump housing.
3. Inspect the rubber anti-drainback valve
and remove any debris.
4. Unscrew the connections and inspect
the outlet anti-drainback valves (Viking
Power Vacuum).
5. Assemble the connections, the pump
housing and the clamps.
Waste management / Recycling
Dispose of the product in accordance with
existing regulations.
Where appropriate, dismantle and sort the
product by its material fractions.
9
Original instructions
> English

Troubleshooting
Symptom Cause Solution
1. The pump doesn’t run. 1.1 Tripped thermal protector 1.1.1 Check the fuse. Let the
or blown fuse. motor cool down before
restart if it is overheated.
1.2 Faulty wire connection or 1.2.1 Check the battery/power
power supply. supply, main switch and
wiring.
1.4 Motor malfunctioning. 1.4.1 Change pump.
1.5 Pump/motor frozen. 1.5.1 Thaw pump and system
and check for damage.
There is a risk of damage
if a frozen pump/motor
is started.
2. The pump does not prime. 2.1 The water tank is empty. 2.1.1 Fill up the tank.
2.2 Debris under/in the valves. 2.2.1 Open the pump by body
by unscrewing the two
screws and clean the
valves. Clean the outlet
valves. (Viking Power
Vacuum.)
2.3 Perforated diaphragm. 2.3.1 Replace the diaphragm.
2.4 Leak on inlet side of pump. 2.4.1 Check tightness of hose
connections.
2.5 Inlet or outlet plumbing 2.5.1 Check the plumbing and
restricted. the valves.
3. Low flow/pressure. 3.1 Lean on outlet side of 3.1.1 Check the tightness of
pump. the connections. Check
the hose for possible
damage.
3.2 Perforated diaphragm. 3.2.1 Replace the diaphragm.
3.3 Motor malfunctioning. 3.3.1 Replace the pump.
3.4 Debris under/in the valves. 3.4.1 Open the pump body by
unscrewing the two screws
and clean the valves. Clean
the outlet valves. (Viking
Power Vacuum.)
4. Pump is excessively noisy. 4.1 Inlet or outlet plumbing 4.1.1 Check the hoses and the
restricted. plumbing.
4.2 Restriction on outlet side of 4.2.1 Ensure that the valves are
the pump/too high pressure open.
4.3 Defective motor. 4.3.1 Replace the pump.
10
Original instructions
> English

09-47181
09-47183
09-47182
09-47182
09-47264
Parts list
09-47181
Diaphragm kit
09-47182 Viking Power 32
Pump house cpl
09-47264
Clamp kit
09-47183 Viking Power Vacuum
Pump house cpl
27

Pump no. 10-13373-05, 06, 07, 08
Pump no. 10-13373-01, 02, 03, 04
101 mm
192 mm
338 mm
192 mm
277 mm
321( mm )
139 mm
264 mm
139 mm 74 mm
340 mm
Dimensions
28 Check out the collection of boat parts & hardware we offer.