Spyder Climb Right Mini Grab User manual

A division of Spyder Manufacturing
Replacement Parts Available!
Read and understand all Instructions
and Warnings before use!
MINI Grab
• Rope Grab with Internal Spring
• High quality Aircra aluminum
• Double locking thread security
• Mini Grab ts 3/8” to 1/2” rope
Check out our other products at
www.SpyderMan.com
1-714-528-8010
Climb Hard, Climb Safe,
#03300 V1.2
• 3/16CenterBolt
• AluminumCam
• 10-32setscrew
The Climb Right Mini-ClencherTMisdesignedtoadjusttheconnectionpointon
aropeorpositioninglanyardbymeansofaslidingropegrab.
Tools Required:
• 3/32”AllenWrench
• 3/16”AllenWrench
• 1/2”WrenchorSocket
1. Removethenylocknutfromthecenterboltthreadsusinga
1/2”wrenchorsocket.
2. Removethecenterboltusinga
3/16”allenwrench.
3. Removethecamandtheinternal
springfromthebody.
4. Removetheinternalspringfrom
thecambylooseningthesetscrew
witha3/32”allenwrench
Disassembly Instructions:
Spring
Cam
Center Bolt
1/2” Nylock Nut
Body
Parts Included:
• AluminiumBody
• 1/2”nylocknut
• InternalCoiledSpring
Assembly Instructions:
1. Insertspringintotherecessedholeinthecam.
2. Usinga3/32”allenwrench,insertthesetscrew
intothecamandlightlytighten.Over
tighteningwillcausethespringtodistort.
3. Insertthecamintothebodymakingsure
thespringlinesupwiththesmallhole.
4. Insertthecenterboltandtightenusing
a3/16”allenwrench.
5. Screwonthenylocknutandtighten
witha1/2”wrench.
6. ArrowmustpointawayfromOperator.
Set Screw
Spring
1 & 2
3
Slide spring into small
hole
Insert center bolt
and tighten
Screw on nylock nut
and tighten
4 &5
Prop 65 warning: is product may contain a chemical known to the State of
California to cause cancer, birth defects, or other reproductive harm
Set Screw
6

WARNINGS:
Part Number: Date First Used:
Serial Number: Purchased From:
Notes: Purchase Date:
Examinations Records Chart
A full PDF version of this insert can be found at www.spyderman.com/info
• is is to be used only by trained professionals.
• Not for belay or fall arrest.
• is product is a type II system and may only be used for work positioning.
• is device is not to be used directly on wire rope or steel cable.
• Correct locking action is dependent on proper orientation of the rope grab. e arrow on the housing of
the rope grab must point away from operator.
• While on the ground, check to be sure that the rope grab will not slide back towards operator. When slack
is removed from cam, the rope grab should only slide in the direction indicated by the arrow on the rope
grab housing.
• Never use near electrical lines or anything that can conduct electricity. Never use if there is a risk of
lightning.
• Never use this as your sole life support. You must always be attached by two dierent systems at all times!
• Always inspect your rope grab for proper installation and operations before every climb!
• You must also have your Climb Right Rope Grab inspected by someone other than yourself who is quali-
ed to inspect this type of gear a minimum of twice a year.
• You must retire your rope grab if it is not t for service, or if it is two years old from the rst date of use,
whichever comes rst.
• e Climb Right Rope Grab must never be modied! Doing so can compromise the integrity of the Rope
Grab and may result in a failure which can lead to injury or death.
• Only use industry approved methods for using this equipment.
• Retire immediately aer shock loading as this can aect the integrity and strength of the rope grab.
• Check aluminum housing and cam for any cracks, deformity, corrosion, wear, ETC. If any of these condi-
tions are present, immediately retire rope grab from service.
• Check the rope grab cam teeth to make sure they are not clogged with dirt, debris, grime, or anything that
might aect the proper function of the rope grab. If it cannot be cleaned or cleared, retire rope grab from
service.
• Double check rope grab to make sure cam can move freely without getting stuck or jammed.
Make sure internal spring promptly places tension back onto the rope. Replace sping if
no longer working properly. If it is replaced with a new spring and still does not function
properly, remove rope grab from service.
• Only use with compatible equipment and components.
• Never operate the rope grab without the center bolt securely in place with the lock nut properly installed.
Lock nut must be replaced aer loosening or removal. Use only a nylon insert jam nut. Do not over
tightnen. e lock nut should be locked onto the center bolt, but not squezing or gripping onto the rope
grab body.
**Rated for a Safe Working Load Limit (WLL) of 350 lbs when fully equipped.
Date Examination Notes Examined By Signature
EXAMINATION RECORDS
For current safety information, please
visit www.spyderman.com/info