Ss Brewtech FTSs Pro User manual

ENGINEERING BETTER BEER
FTSs Pro Modular Temperature Controller
- Europe -

Page 2
OVERVIEW
The FTSs Pro Modular Temperature Controller works in conjunction with a pressurized glycol system to
provide temperature control over the contents of your vessel. It functions by using a temperature sensor
to read the present value (PV) of your vessel, and triggering an output based on the set value (SV) in
order to match PV with SV. When cooling is called for, the solenoid valve will open to allow the ow of
glycol through your vessel’s cooling jackets or coils until the set value is achieved.
INTRODUCTION
Temperature
OFF
Run Crash
FTSs Pro Controller
Solenoid Valve

Page 3
POWERING THE FTSs PRO
The FTSs Pro Modular Temperature Controller comes with a lead marked “110~240VAC-in”. The
three wires in this cable correspond to hot (brown wire), neutral (blue wire), and ground (green/yellow
wire). A plug is purposely omitted from the cable to accommodate various methods used for supplying
110~240VAC to the unit. If you are installing a plug, BE SURE that a GFCI breaker/receptacle is
installed.
SETUP
Temperature
OFF
Run Crash
110~240VAC-In
Brown - Hot
Blue - Neutral
Green/Yellow - Ground
To Temperature Sensor
Solenoid Connection
SENSOR INSTALLATION
The FTSs Pro Modular Temperature Controller comes with a lead marked “Sensor”. The two wires in
this cable (red and black) will connect to your temperature sensor. If you are using an Ss Brewtech
vessel, your tank comes equipped with a PT100 platinum resistance thermometer. The red and black
wires will connect to terminals 1 and 2 on the thermometer’s plug. The orientation of the wires does not
matter, as long as they are connected to terminals 1 and 2.
SOLENOID INSTALLATION
The FTSs Pro Modular Temperature Controller comes with either a ½” (1-3.5 bbl Unitank) or ¾” (5 bbl
and larger Unitank) electric solenoid valve. Installation can be handled in a variety of ways based on
preference and setup. We recommend installation of a manual bypass piping/valve arrangement, as
well as piping/valve arrangement to clear the line of glycol in the event that service is needed.

Page 4
SETTINGS
Ss Brewtech Pro Tanks ship with a PT100 type temperature senor included. To set the temp sensor
type, begin by pressing the “Level Key” (3 or more seconds).
Then press the “Mode Key” until you see “Cn-t”. Finally press the “Up” or “Down” Key to select “1” for a
PT100 probe. For other temp sensor options, please reference the table on the following page.
Press and hold the “Level Key” for more than 3 seconds to return to the primary display.
The input setting can be manipulated based on the type of sensor being used. The correct input setting
for a PT100 sensor is “Cn-t: 1”. This should be the default setting on your controller. If you are reading a
sensor error message (S.ERR), double check your connections to the sensor and ensure that “Cn-t” is
set to 1. If you are using a different type of sensor, see the included chart to determine the proper input
setting for your particular sensor.
SENSOR: SETTINGS & CALIBRATION
Up KeyLevel Key
Operation Indicators
Down KeyMode Key
Shift Key
No. 1 Display
Temperature Unit
No. 2 Display

Page 5
SENSOR: SETTINGS & CALIBRATION (CONTINUED)
OTHER TEMP SENSOR OPTIONS
Input type Name Set
Value
Input Temperature Setup Range
Platinum resis-
tance ther-
mometer input
type
Platinum
resistance
thermometer
Pt100
0
1
2
JPt100 3
4
Input type Name Set
Value
Input Temperature Setup Range
Thermocouple
input type
Thermocouple
K 0
1
J 2
3
T 4
17
E 5
L 6
U 7
18
N 8
R 9
S 10
B 11
Infrared 12
t
empera
t
ure
13
senso
r
14
ES1
A
15

Page 6
SENSOR: SETTINGS & CALIBRATION (CONTINUED)
CALIBRATION
Before use, it is important to ensure that your sensor is properly calibrated. There are several ways of
calibrating a temperature sensor, but the simplest way is to use an ice-water mixture. When you insert
your sensor into an ice-water mixture, it should read 32°F (0°C). Perform the “ice method” of calibration
and document the offset, if any. You can then set a temperature offset on the controller to reect
this variation.
Press the “Level Key” for less than 1 second, and then use the “Mode Key” until you see “Cn5”. Next
use the “Up” or “Down” Key to change the temperature offset.
Press the “Level Key” for less than 1 second to exit to the main screen.
Up KeyLevel Key
Down KeyMode Key
No. 1 Display
Temperature Unit
No. 2 Display

Page 7
ADDITIONAL MENU SETTINGS
TEMPERATURE UNITS
HYSTERESIS
The FTSs Pro Modular Temperature controller uses an Omron Digital Controller as the “brains of the
operation”. It contains a whole host of menu options and settings that are not crucial to the basic
functioning of your FTSs Pro. Outlined below are a few of the more pertinent menu settings. For more
detailed information, please consult the Omron Programming Guides.
The FTSs Pro Modular Temperature Controller allows the user to toggle between Fahrenheit and
Celsius. To do so, hold the “Level Key” for 3 or more seconds and then press the “Mode Key” until you
see “d-U”. Press the “Up” or “Down” Keys to toggle between Fahrenheit (F) and Celsius (C).
The FTSs Pro Modular Temperature Controller allows you to set a hysteresis value. This value
represents the number of degrees away from the set value that the Omron will trigger an output. Press
the “Level Key” for 3 or more seconds and then press the “Mode Key” until you see “HYS”. Press the
“Up” or “Down” Keys to adjust the value.
For example, if the hysteresis is set to “1” (default setting), then the solenoid valve will only open when
the PV is one degree or greater above the SV. We recommend leaving this value at “1” to prevent
over-cycling of the system.
Up Key
Up Key
Level Key
Level Key
Down Key
Down Key
Mode Key
Mode Key
No. 1 Display
No. 1 Display
No. 2 Display
No. 2 Display

Page 8
ADDITIONAL MENU SETTINGS (CONTINUED)
DECIMAL POINTS
The controller can be set to adjust the decimal point displayed on the controller. This is handy if you
wish to have ner temperature control, or if you are using a smaller hysteresis value. Press and hold
the “Level Key” for less than 1 second and then press the “Mode Key” until you see “dP”. Use the “Up”
or “Down” Keys to move the decimal points. Press the “Level Key” for less than 1 second to exit.
Up KeyLevel Key
Down KeyMode Key
No. 1 Display
No. 2 Display

Page 9
OPERATIONS
RUN
CRASH
When in “Run” mode, the user can select a set value using the up and down keys. This can be used to
maintain fermentation temperatures, or for cooling purposes. When the set value is below the present
value, “OUT” will display on the controller and the solenoid valve will open. When the set value is
achieved, “OUT” will disappear from the display and the solenoid valve will close.
When in “Crash” mode, the user can quickly toggle to a programmable “crash” temperature (0°C, for
example). The controller will memorize this temperature, and by simply turning the switch you can
switch to this temperature without toggling the up and down keys.
Temperature
OFF
Run Crash
OUT1
OUT1
Temperature
OFF
Run Crash

REV 04182019
SsBrewtech.com