4
English
Scope of supply SETCA812-3
• CA 812-4
• 3 x HTS 811-…
• TR 603-…
• Siedle screwdriver
• This product information
Scope of supply SETCA812-4
• CA 812-4
• 4 x HTS 811-…
• TR 603-…
• Siedle screwdriver
• This product information
Mounting CA812-…
1 Unscrew the front of the housing.
To do this, release the Siedle screw
on the underneath of the housing.
Hinge the front of the housing
forward.
2 Surface mounting the door station.
Recommended mounting height
appr. 1.50m /4.9ft. to centre device.
Please note: The cable is inserted in
the lower area of the base plate!
3 Strip back the installation cable
close to the wall (appr. 10 mm)
and insert the cores into the base
plate. Fasten the base plate using 4
screws. Close the two openings at
the top using rubber stoppers. Install
in accordance with the terminal
diagram.
The cores may only be laid in the
admissible installation space.
4 Depending on the installation
environment, it may be necessary
to change the door station speech
volume in order to permit clear
speech transmission.
5 Hook the front of the housing
onto the base plate at the top and
close. Tighten the screw on the
underneath of the housing.
Mounting TR603-…
6 Mount the transformer on the top
hat rail (distribution).
7 Surface mounting is possible with
accessory ZAP30. (not included in
scope of supply)
Mounting HTS811-…
Strip back cable to appr. 80mm.
8 Open the device from the back by
pressing in the locking lever.
Application
Siedle Compact audio set in 1+n
technology with the functions
calling, speech and door release.
Number of integrated call buttons:
1,2,4
Each Compact set can be extended
with an additional indoor station
per call button and enhanced with a
secondary signal unit.
CA812-… door station
performance Features:
• Integrated door loudspeaker
• Adjustable voice volume
• Number of integrated call but-
tons: 1(CA812-1), 2(CA812-2),
4(CA812-3/4)
• Backlit nameplates exchangeable
from the front
• Backlit info sign for house number,
logos, opening times, etc.
• For surface mounting with housing
front made of high-quality plastic
HTS811-0 indoor station
performance Features:
• Door call as 3-tone call
• Storey call as 2-tone call in
Compact set with ZERT811-0 pos-
sible
• Integrated call silencing via volume
control
• Can volume can be innitely
adjusted to max. 83dB(A) via
volume control from outside
• Parallel switching of max. 2
telephones without internal com-
munication
• Integrated door release and light
button
• Can be used as a table-top unit
using table-top accessory ZTS800-…
• Plug-in spiral cable for simple
installation
TR603-0 transformer
performance Features:
• Thermal protection
• Double terminals (secondary)
• Compact design
Electrical voltage
• Mounting, installation and ser-
vicing work on electrical devices may
only be performed by a suitably
qualied electrician.
• Failure to observe this regulation
could result in the risk of serious
damage to health or fatal injury due
to electric shocks.
• Observe DIN EN 60065!
In a building installation, an all-pole
mains switch with a contact opening
of at least 3 mm must be provided.
The transformer must not be
exposed to water drops or sprayed
water! Ensure sufcient ventilation,
paying particular attention to ensure
that ventilation slots are not covered.
• For surface mounting, ensure that
“protection against direct contact”
with active parts is provided. For
details, consult VDE0100/DIN57100
part410.
• When using stranded cores as
cable material, these must be tted
with wire end ferrules without fail.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply SETCA812-1
• CA 812-1
• HTS 811-…
• TR 603-…
• Siedle screwdriver
• This product information
Scope of supply SETCA812-2
• CA 812-2
• 2 x HTS 811-…
• TR 603-…
• Siedle screwdriver
• This product information
