Stahls Hotronix CP912-120 User manual

Available model: CP912-120
The Craft Press
OPERATOR’S MANUAL

When using your heat press,
basic precautions should always be followed,
including the following:
Product Warranty Registration
Log onto www.Hotronix.com/registration
You must provide the Hotronix®heat press
serial number and model information.
Read all instructions.
Use heat press only for its intended use.
To reduce the risk of electric shock, do not immerse the heat press in water or other liquids.
Never pull cord to disconnect from outlet, instead grasp plug and pull to disconnect.
Do not allow cord to touch hot surfaces, allow heat press to cool completely before storing.
Do not operate heat press with a damaged cord or if the equipment has been dropped or damaged. To
reduce the risk of electric shock, do not disassemble or attempt to repair the heat press. Take it to a
qualified service person for examination and repair. Incorrect assembly or repair could increase the risk of
fire, electric shock, or injury to persons when the equipment is used.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Close supervision is necessary for any heat press being used by or near children. Do not leave
equipment unattended while connected.
Burns can occur when touching hot metal parts.
To reduce the likelihood of circuit overload, do not operate other high voltage equipment on the same
circuit.
If an extension cord is necessary, then a 20 amperage rated cord should be used. Cords rated for less
amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled
or tripped over.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Safety Instructions
S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M

S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M
The Craft Press
Safety Instructions
Machine View
Control Panel Guide
Operating Instructions
Connecting the System
Turning the System On
Adjusting the Temperature
Adjusting the Time
Adjusting the Pressure
Pressing
Contact
2
4
5
6-11
6
7
8
9
10
11
15
Table of Contents

S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M
The Craft Press
PAGE 4
Machine View
Control Panel
Lift Handle (Up)
Lower Platen
Power Switch
Circuit Breaker
Power Cord
Upper Platen (Heater)
Pressure Knob
Lift Handle (Down)

S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M
The Craft PressThe Craft Press
PAGE 5
Digital Display
Temperature Indicator
Set Indicator
Time Indicator
Increase
Mode Select
Decrease
MODE
Control Panel Guide

S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M
The Craft Press
Connecting the System
CONNECT THE POWER CORDConnect the power cord into a properly grounded electrical outlet with a sufficient
amperage rating.
VOLTAGE:
120 Volt - The Craft Press Digital Clam requires a full 20 amp grounded circuit for 120 volt operation.
220 Volt - The Craft Press Digital Clam requires a full 10 amp grounded circuit for 220 volt operation.
EXTENSION CORDS: If used, should be as short as possible and not less than 12 gauge.
Heavy duty cords are recommended.
CIRCUITS: that have less than 15 amps or that have other high demand equipment or heat presses
plugged in should not be used.
NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly
qualified person in order to avoid hazard. Use SJT type rated 300 V cord for replacement.
CAUTION: Failure to follow these instructions will cause:
1. Erratic controller functions. 2. Inaccurate displays and slow heat-up. 3. The circuit breaker to disengage.
The Craft Press DIGITAL CLAM
The Craft Press Digital Clam Operating Instructions are designed with the user in mind. Carefully read and follow the step-
by-step instructions for best results.
To avoid burns, do not touch the heated platen
during use.
Keep hands clear of the upper platen of the press
during platen lock down as the pressure may
cause injury.
Press should be placed on a sturdy, suitable stand
at least 36”L x 24”W x 29”H.
Work area must be kept clean, tidy and free of
obstructions.
1.
PAGE 6
Operating Instructions
1.1

S E R V I C E H O T L I N E : 8 0 0 . 7 2 7 . 8 5 2 0 H O T R O N I X . C O M
The Craft PressThe Craft Press
Adjusting Temperature, Time & Pressure
Press the MODE button to cycle through setup modes (with the press ON and the Lift Handle in the UP position):
Displays current
temperature (°F) Displays print temperature Displays print time (sec)
Ready to Print Decrease using (-) button Decrease using (-) button
Increase using (+) button Increase using (+) button
Various transfer products will recommend using either “light,” “medium” or “heavy” pressure. Some trial and error may be
required to determine the best pressure setting, but once selected your Sports Ball Heat Press will reliably reproduce the
same pressure, print after print.
With the lift handle in the DOWN position, rotate the patented, Over-the-Center Pressure Adjustment Knob.
Rotate clockwise to increase pressure
Rotate counter-clockwise to decrease pressure
Remember to allow for the thickness of your garment
when adjusting the pressure.
WARNING: Structural damage caused by excessive pressure is not covered
under the limited warranty!

The Craft Press
PAGE 11
Printing with your Craft Press
Once the Craft Press has reached the designated
temperature, position the garment on the lower platen.
Align the transfer material on the garment to be printed.
Lower and lock the heat platen into the press position.
The automatic timing process will start.
The timer will count down and audibly signal you to lift the heat
platen into the UP position when the press cycle is complete. The
time will automatically re-set and you are ready to continue with
the next application.

Rev. A 4-14 Doc. MAXX11 - MAXX15 - MAXX20 9-12
Stahls’ Hotronix®
One Industrial Park
Carmichaels, PA 15320
U.S.A.
Technical Support
800 . 727 . 8520
Monday - Friday
8am - 7pm EST
Customer Service
800 . 727 . 8520
Monday - Friday
8am - 5pm EST
Replacement Parts
800 . 727 . 8520
8am - 7pm EST
Web
Hotronix.com
The Craft Press
Printing with your Craft Press
This document includes multiple trademarks and describes equipment covered by many patents
that are owned by GroupeSTAHL and/or its subsidiaries. GroupeSTAHL enforces its rights
to protect these intellectual properties. © 2015
Contact Us

One Industrial Park . Carmichaels, PA 15320, U.S.A.
Tech Support - Customer Service - Replacement Parts: 800 . 727 . 8520
Web: Hotronix.com
Proudly made in the U.S.A.