Stanley 70501 Troubleshooting guide

INSTRUCTION AND
SERVICE MANUAL
70501 Module for Speed Fasteners
Hydro-Pneumatic Power Module
EN
Hydro-Pneumatic Power Module
BG
  
HR
Hidro-pneumatski modul napajanja
CZ
Hydropneumatický modul
RO
Modul hidro-pneumatic
HU
Hidro-pneumatikus elektromos modul
SK
Hydropneumatický modul
SL
Hidro-pnevmatski pogonski modul
RU
  
AR
LV
Hidropneimatiskais spēka modulis
LT
Hidraulinis-pneumatinis elektrinis modulis
ET
Hüdropneumaatiline elektrimoodul
EL
Υδροπνευατική ονάδα ισχύο
TR
Hidro-Pnömatik Güç Modülü

2
©2021 STANLEY Black & Decker
All rights reserved.
The information provided may not be reproduced and/or made public in any way and through any means (electronically
or mechanically) without prior explicit and written permission from STANLEY Engineered Fastening. The information
provided is based on the data known at the moment of the introduction of this product. STANLEY Engineered Fastening
pursues apolicy of continuous product improvement and therefore the products may be subject to change. The information
provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore, STANLEY Engineered
Fastening cannot be held liable for any damage resulting from deviations from the original specications of the product.
The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not
accept any liability with respect to any faults in the information nor for the consequences thereof. STANLEY Engineered
Fastening will not accept any liability for damage resulting from activities carried out by third parties. The working names,
trade names, registered trademarks, etc. used by STANLEY Engineered Fastening should not be considered as being free,
pursuant to the legislation with respect to the protection of trademarks.
CONTENT
1. SAFETY DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.1 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 PROJECTILE HARZARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 OPERATING HAZARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4 REPETITIVE MOTIONS HAZARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5 ACCESSORY HAZARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 WORKPLACE HAZARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.7 NOISE HAZARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.8 ADDITIONAL SAFETY INSTRUCTIONS FOR HYDRAULIC POWER TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.1 INTENT OF USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 TOOL SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 TOOL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. PUTTING IN SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4. OPERATING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5. SERVICING THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.1 DAILY SERVICING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.2 WEEKLY SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.3 ANNUAL SERVICING / EVERY 500K OPERATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5.4 SERVICE KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.5 HYDRAULIC OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.6 DISMANTLING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.7 PROTECTING THE ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. GENERAL ASSEMBLY AND PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.1 GENERAL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
6.2 PARTS LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
7. SAFETY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1 HYSPIN VG32 OIL SAFETY DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
7.2 MOLYLITHIUM GREASE EP 3753 - SAFETY DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
7.3 MOLYKOTE® 111 GREASE - SAFTEY DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
8. EC DECLARATION OF INCORPORATION FOR PARTLY COMPLETED MACHINERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. UK DECLARATION OF INCORPORATION FOR PARTLY COMPLETED MACHINERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
10. PROTECT YOUR INVESTMENT! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ENGLISH ORIGINAL INSTRUCTION

3
This instruction manual must be read by any person installing or operating this tool with particular attention to
the following safety warnings and instructions.
Always wear impact-resistant eye protection during operation of the tool. The grade of protection required
should be assessed for each use.
Use of the tool can expose the operator’shands to hazards, including crushing, impacts, cuts and abrasions and
heat. Wear suitable gloves to protect hands.
Use hearing protection in accordance with employer’sinstructions and as required by occupational health and
safety regulations.
1. SAFETY DEFINITIONS
The denitions below describe the severity for each signal word. Please read the manual and pay attention to these symbols.
!DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.
!WARNING: Indicates apotentially hazardous situation which, if not avoided, could result in death or serious injury.
!CAUTION: Indicates apotentially hazardous situation which, if not avoided, may result in minor or moderate injury.
!CAUTION: Used without safety alert symbol indicates apotentially hazardous situation which, if not avoided, may
result in property damage.
Improper operation or maintenance of this product could result in serious injury and property damage.
Read and understand all warnings and operating instructions before using this equipment. When using
power tools, basic safety precautions must always be followed to reduce the risk of personal injury.
When the tool is operated it must not be held in the hand or be in contact with any part of the body. There is
apossibility of ashear injury when the piston retracts.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
1.1 GENERAL SAFETY RULES
• For multiple hazards, read and understand the safety instructions before installing, operating, repairing, maintaining,
changing accessories on, or working near the tool. Failure to do so can result in serious bodily injury.
• Only qualied and trained operators must install, adjust or use the tool.
• DO NOT use outside the design intent of placing STANLEY Engineered Fastening Blind Rivets.
• Use only parts, fasteners, and accessories recommended by the manufacturer.
• DO NOT modify the tool. Modications can reduce the eectiveness of safety measures and increase the risks to the
operator. Any modication to the tool undertaken by the customer will be the customer’sentire responsibility and void
any applicable warranties.
• Do not discard the safety instructions; give them to the operator.
• Do not use the tool if it has been damaged.
• Prior to use, check for misalignment or binding of moving parts, breakage of parts, and any other condition that aects
the tool’soperation. If damaged, have the tool serviced before using. Remove any adjusting key or wrench before use.
• Tools shall be inspected periodically to verify that the ratings and markings required by this part of ISO 11148 are
legibly marked on the tool. The employer/user shall contact the manufacturer to obtain replacement marking labels
when necessary.
• The tool must be maintained in asafe working condition at all times and examined at regular intervals for damage
and function by trained personnel. Any dismantling procedure will be undertaken only by trained personnel. Do not
dismantle this tool without prior reference to the maintenance instructions.
ORIGINAL INSTRUCTION ENGLISH

4
1.2 PROJECTILE HARZARDS
• Disconnect the tool from the hydraulic supply before performing any maintenance, attempting to adjust,  t or remove
a nose assembly or accessories.
• Be aware that failure of the workpiece or accessories, or even of the inserted tool itself can generate high-velocity
projectiles.
• Always wear impact-resistant eye protection during operation of the tool. The grade of protection required should be
assessed for each use.
• The risks to others should also be assessed at this time.
• Ensure that the workpiece is securely xed.
• Check that the means of protection from ejection of fastener and/or mandrel is in place and is operative.
• Warn against the possible forcible ejection of mandrels from the front of the tool.
• DO NOT operate atool that is directed towards any person(s).
1.3 OPERATING HAZARDS
• When the tool is operated it must not be held in the hand or be in contact with any part of the body. There is
apossibility of ashear injury when the piston retracts.
• Use of the tool can expose the operator’shands to hazards, including crushing, impacts, cuts and abrasions and heat.
Wear suitable gloves to protect hands.
• Release the start-and-stop device in the case of an interruption of the hydraulic supply.
• Use only lubricants recommended by the manufacturer.
• Contact with hydraulic uid should be avoided. To minimise the possibility of rashes, care should be taken to wash
thoroughly if contact occurs.
• Material Safety Data Sheets for all hydraulic oils and lubricants is available on request from your tool supplier.
• If the tool is xed to asuspension device, make sure that the xation is secure.
• Beware of the risk of crushing or pinching if nose equipment is not tted.
• DO NOT operate tool with the nose casing removed.
• When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent activation.
• DO NOT abuse the tool by dropping or using it as ahammer.
• Care should be taken to ensure that spent mandrels do not create ahazard.
1.4 REPETITIVE MOTIONS HAZARDS
• When using the tool, the operator can experience discomfort in the hands, arms, shoulders, neck or other parts of the
body.
• While using the tool, the operator should adopt acomfortable posture whilst maintaining asecure footing and
avoiding awkward or o -balance postures. The operator should change posture during extended tasks; this can help
avoid discomfort and fatigue.
• If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing, aching, tingling,
numbness, burning sensations or sti ness, these warning signs should not be ignored. The operator should tell the
employer and consult aqualied health professional.
1.5 ACCESSORY HAZARDS
• Disconnect the tool from the hydraulic supply before tting or removing the nose assembly or accessory.
• Use only sizes and types of accessories and consumables that are recommended by the manufacturer of the tool; do
not use other types or sizes of accessories or consumables.
1.6 WORKPLACE HAZARDS
• Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces caused by use of the tool and
also of trip hazards caused by the air line or hydraulic hose.
• Proceed with care in unfamiliar surroundings. There can be hidden hazards, such as electricity or other utility lines.
• The tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electric
power.
• Ensure that there are no electrical cables, gas pipes, etc., which can cause ahazard if damaged by use of the tool.
ENGLISH ORIGINAL INSTRUCTION

5
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
• Care should be taken to ensure that spent mandrels do not create ahazard.
1.7 NOISE HAZARDS
• Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus
(ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and the implementation of appropriate
controls for these hazards are essential.
• Appropriate controls to reduce the risk may include actions such as damping materials to prevent workpieces from
“ringing”.
• Use hearing protection in accordance with employer’sinstructions and as required by occupational health and safety
regulations.
• Operate and maintain the tool as recommended in the instruction manual, to prevent an unnecessary increase in the
noise level.
1.8 ADDITIONAL SAFETY INSTRUCTIONS FOR HYDRAULIC POWER TOOLS
• The operating hydraulic supply must not exceed 140 bar (2030 PSI).
• Oil under pressure can cause severe injury.
• Do not t exible hydraulic hoses rated at less than 700 bar (10,000 PSI) working pressure at aow rate of 2.73 l/min
(200 in 3/min).
• Disconnect hydraulic hoses from the pump unit when tool is not in use, before changing accessories or when making
repairs.
• Whipping hoses can cause severe injury. Always check for damaged or loose hoses and ttings.
• Prior to use, inspect hydraulic hoses for damage, all hydraulic connections must be clean, fully engaged and tight
before operation. Do not drop heavy objects on hoses. Asharp impact may cause internal damage and lead to
premature hose failure.
• Whenever universal twist couplings (claw couplings) are used, lock pins shall be installed and whipcheck safety cables
shall be used to safeguard against possible hose-to-tool or hose-to-hose connection failure.
• DO NOT lift the placing module by the hose. Always use the placing module body.
• Keep dirt and foreign matter out of the hydraulic system of the tool as this will cause the tool to malfunction.
• Use only clean oil and lling equipment.
• Only recommended hydraulic uids may be used.
• Maximum temperature of the hydraulic uid at the inlet is 110°C (230°F).
STANLEY Engineered Fastening policy is one of continuous product development and improvement and we reserve
the right to change the specication of any product without prior notice.
ORIGINAL INSTRUCTION ENGLISH

6
2. SPECIFICATION
2.1 INTENT OF USE
The 70501 Module is principally apiston and cylinder assembly. When coupled hydraulically to acompatible hydraulic
power source and the relevant nose equipment is attached, it is then used to install 1/16”Avlug® speed rivets, in Industrial
Environments.
The placing module may only be used in accordance with the operating instructions for placing Stanley Engineered
Fastening rivets.
DO NOT use under wet conditions or in the presence of ammable liquids or gases.
The safety instructions must be followed at all times.
2.2 TOOL SPECIFICATION
SPECIFICATION METRIC IMPERIAL
Force: Pull at stated pull pressure 3.0 kN 674 lbf
Pressure: Hydraulic pressure 140 bar 2030 PSI
Stroke: Piston Stroke 30.0 mm 1.18 in
Cycle Time: Maximum 1 second -
Weight: Without nose equipment kg lb
2.3 TOOL DIMENSIONS
All dimensions are shown in millimetres.
ENGLISH ORIGINAL INSTRUCTION

7
3. PUTTING IN SERVICE
IMPORTANT - READ THE SAFETY RULES ON PAGES 3 - 5 AND THE TECHNICAL MANUAL SUPPLIED WITH THE
COMPLETE MACHINE CAREFULLY BEFORE PUTTING INTO SERVICE.
THE MODULE IS DESIGNED TO OPERATE AS PART OF ACOMPLETE AUTOMATED OR SEMI-AUTOMATED MACHINE.
WHEN THE TOOL IS CYCLED IT MUST NOT BE HELD IN THE HAND OR BE IN CONTACT WITH ANY PART OF THE BODY.
THERE IS APOSSIBILITY OF ASHEAR INJURY WHEN THE PISTON RETRACTS.
Instructions on installing and removing the module from the machine frame will be included in the Technical Manual
supplied with the machine. The Technical Manual will include full instructions on putting the module into service, together
with instructions on the dismantling, maintenance and assembly of the Nose Equipment.
4. OPERATING INSTRUCTIONS
IMPORTANT - READ THE SAFETY RULES ON PAGES 3 - 5 AND THE TECHNICAL MANUAL SUPPLIED WITH THE
COMPLETE MACHINE CAREFULLY BEFORE OPERATING THE TOOL.
Refer to the Technical Manual supplied with the machine for operating instructions.
5. SERVICING THE TOOL
IMPORTANT - READ THE SAFETY RULES ON PAGES 3 - 5 AND THE TECHNICAL MANUAL SUPPLIED WITH THE
COMPLETE MACHINE.
THE EMPLOYER IS RESPONSIBLE FOR ENSURING THAT TOOL MAINTENANCE INSTRUCTIONS ARE GIVEN TO THE
APPROPRIATE PERSONNEL. THE OPERATOR SHOULD NOT BE INVOLVED IN MAINTENANCE OR REPAIR OF THETOOL
UNLESS PROPERLY TRAINED. THE TOOL SHALL BE EXAMINED REGULARLY FOR DAMAGE AND MALFUNCTION.
Refer to the Technical Manual supplied with the machine for full service instructions.
5.1 DAILY SERVICING
• Check placing tool, hoses and connectors for oil leaks.
• Worn or damaged hoses and connectors should be replaced.
• Check that the stroke of tool meets the specication.
• Check that the supply pressure is correct and does not exceed 140 bar.
• Check the nose equipment, mandrel and follower springs for wear, replace as necessary.
5.2 WEEKLY SERVICING
• Dismantle and clean the nose equipment, especially the jaws, as described in the Technical Manual for the Machine.
• Check for oil leaks in placing tool, hoses and quick couplers.
!CAUTION – Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
5.3 ANNUAL SERVICING / EVERY 500K OPERATIONS
• Every 500,000 cycles the tool should be completely dismantled and new components should be used where worn,
damaged or as recommended. All O-rings, back-up rings and seals should be renewed and lubricated with MolyKote®
111 grease before assembling.
ORIGINAL INSTRUCTION ENGLISH

8
5.4 SERVICE KIT
For acomplete service the following Service Kit is available:
SERVICE KIT: 70500-99990
PART NUMBER DESCRIPTION QTY. PART NUMBER DESCRIPTION QTY.
07900-00013 Hexagon Wrench 1/8”A/F 1 07900-00522 Combination Spanner 2
70900-00194 Jaw Housing Key 1 07900-00006 Spatula 1
07900-00226 Hexagon Wrench 6mm A/F 1 07900-00201 Hexagon Wrench 0.50”A/F 1
07900-00433 Spanner 24 & 26mm Open
Ended 107900-00669 Assy. Bullet (Piston) 1
07900-00434 Spanner 32 & 30mm Open
Ended 1 07900-00577 Piston Assy Rod 1
07992-00020 80gm Moly-lithium Grease
EP3753 1 07900-00429 Assy Spanner for Head Piston 1
5.5 HYDRAULIC OIL
The recommended oil for priming is Hyspin® VG32 available in 0.5l (part number 07992-00002) or one gallon containers
(part number 07992-00006).
5.6 DISMANTLING INSTRUCTIONS
IMPORTANT – ENSURE THE MAINS POWER AND AIR SUPPLY TO THE MACHINE AND HYDRAULIC PUMP UNIT IS
SWITCHED OFF BEFORE DISMANTLING THE TOOL.
Instructions on installing and removing the module from the machine frame will be included in the Technical Manual
supplied with the machine. The Technical Manual will include full instructions on the dismantling, maintenance and
assembly of the tool.
Before Dismantling:
• Remove the module from the machine.
• Remove the nose equipment from the module as per the instructions in the Technical Manual supplied with the
machine.
• The potentially dangerous substances that could have deposited on the machine as aresult of work processes must be
removed before maintenance.
For acomplete service of the tool, we advise that you proceed with dismantling the tool in the order shown
on pages 7 to 9. After dismantling the tool we recommend that you replace all seals.
Dismantling Instructions:
• Remove barrel lock nut (Item 29 x 2) and barrel washer (Item 36 x 2) from barrel.
• Remove rear plug (Item 34) and O-ring (Item 14) by unscrewing using 1" Spanner. Use 1" spanner on rear cylinder (Item
33) to counter the rotation.
• Remove seal retainer (Item 35).
• Slide out piston assembly consisting of items (9, 11, 21, 31 and 32). Use circlip pliers to remove circlip (Item 21) to
disengage piston (Item 31) from piston rod (Item 32).
• Unscrew with 1" spanner rear cylinder (Item 33) and O-ring (Item 14) from second rear cylinder (Item 33). Inside this
cylinder is another O-ring (Item 11). Replace as necessary.
• Remove second seal retainer (Item 35).
• Slide out second piston assembly consisting of items (9, 11, 21, 31 and 32). Use circlip pliers to remove circlip (Item 21)
disengage piston (Item 31) from piston rod (Item 32).
• Unscrew with 1" spanner next rear cylinder (Item 33) and O-ring (Item 14) from front cylinder (Item 49). Inside this
cylinder is another O-ring (Item 11). Replace as necessary.
• Remove third seal retainer (Item 35).
• Unscrew front cylinder (Item 49) from tail jaw housing (Item 47). This pulls out front piston rod (Item 55) and assembly.
• Slide banjo (Item 48) o from cylinder (Item 49).
ENGLISH ORIGINAL INSTRUCTION

9
• Remove turret jaws (Item 26) from turret (Item 53). Unscrew turret (Item 53) from front piston rod (Item 55).
• Optional: Unscrew grub screw (Item 4) from banjo (Item 48).
• Unscrew adaptor (Item 30) from tail jaw housing (Item 47) using 1”spanner and 26mm spanner.
• Using 26mm spanner to hold tail jaw housing (Item 47), unscrew jaw housing (Item 54) using Jaw housing key
(07900-00194).
• Unscrew tail jaw housing (Item 47) from body (Item 43).
• Using 2 x 5/8”spanners remove lock nut (Item 50) from piston (Item 46).
• Unscrew piston nut (Item 51) from piston (Item 46). Separate O-ring (Item 6) from piston nut (Item 51).
• Remove buer stop (Item 52 x 3) from piston (Item 46).
• Unscrew barrel (Item 38) from barrel nut (Item 37) using 18mm spanner.
!WARNING: There may be residual spring load in following two steps. Care must be taken to remove the spring
load.
• Using 6mm hex key, remove screw (Item 3) from barrel retainer (Item 40).
• Slide barrel retainer (Item 40) away from body (Item 43).
• Set aside O-ring (Items 8) and seal (Item 17). Set aside seal spring guides (Item 28).
• Set aside spring (Item 41).
• Remove spring guide (Item 28).
• Slide piston (Item 46) out of body (Item 43).
• Optional: Unscrew button head screws (Item 1) and bonded seals (Item 7) from body (Item 43).
• Remove piston guidance tape-short (Item 45) and hydraulic seal (Item 16) from inside the body (Item 43).
• Set body (Item 43) aside.
• Pull apart piston (Item 46) and barrel nut (Item 37). This exposes an O-ring (Item 8), set aside.
• Remove hydraulic seal (Item 17) and piston guidance tape-long (Item 44).
Assembly Instructions:
• Clean all the parts thoroughly. Inspect and replace any parts that are worn or damaged.
• Assembly is the reverse procedure for dismantling.
• Ensure that the seals are replaced in the correct orientation. Lubricate all seals and housings, with Molylithium Grease
(07992-00020).
• When tting the piston (Item 31) into the body (Item 43), it is essential that the assembly bullet 07900-00669 is used to
prevent seal damage.
All item numbers refer to the General Assembly and Part List in section 6.0.
5.7 PROTECTING THE ENVIRONMENT
• Assure conformity with applicable disposal regulations. Dispose all waste products at an approved waste facility or site
so as not to expose personnel and the environment to hazards.
ORIGINAL INSTRUCTION ENGLISH

10
6. GENERAL ASSEMBLY AND PART LIST
6.1 GENERAL ASSEMBLY
X
SECTION X-X
X
4
306
54
55
34
2131
323333
31 2131
32
21
49
19
48
9
11 11
9
11 11
18
1010
9
11
353535
14141414
47
5252
45
17
44
8
42
2828
12
56520 5350 26
51
46
52
16
23372
43
3
40
41
13
39
15
29
3636
29
3822
77
1 1
ENGLISH ORIGINAL INSTRUCTION

11
6.2 PARTS LIST
70501-02000 Parts List
ITEM PART NUMBER DESCRIPTION QTY.
107001-00114 10-24 UNC BUTTON HEAD SCREW 2
207001-00243 GRUB SCREW 1
307001-00250 M8 SOCKET HEAD CAP SCREW 1
407001-00481 GRUB SCREW M5 CUP 1
507003-00016 "O" RING SEAL 1
607003-00028 "O" RING SEAL 1
707003-00033 BONDED SEAL 2
807003-00036 "O" RING SEAL 1
907003-00042 "O" RING SEAL 5
10 07003-00067 "O" RING SEAL 2
11 07003-00100 "O" RING SEAL 3
12 07003-00121 "O" RING SEAL 1
13 07003-00147 "O" RING SEAL 1
14 07003-00153 "O" RING SEAL 4
15 07003-00178 "O" RING SEAL 1
16 07003-00242 HYDRAULIC SEAL 1
17 07003-00243 HYDRAULIC SEAL 1
18 07003-00248 "O" RING SEAL 1
19 07003-00264 "O" RING SEAL 2
20 07003-00382 "O" RING SEAL 1
21 07004-00057 CIRCLIP 3
22 07007-00017 DUST CAP 1
23 07007-00353 PROTECTIVE PLUG 1
24 73200-02022 SAFETY LABEL (NOT SHOWN) 1
25 07007-02223 ADDRESS LABEL (NOT SHOWN) 2
26 07151-00403 TURRET JAWS 2
27 07273-00203 SAFETY LABEL (NOT SHOWN) 1
28 07650-00218 SPRING GUIDE 2
29 07650-00501 BARREL LOCK NUT 2
30 07657-00302 ADAPTOR 1
31 07657-00305 PISTON 3
32 07657-00306 PISTON ROD 2
33 07657-00307 REAR CYLINDER 2
34 07657-00308 REAR PLUG 1
35 07657-00309 SEAL RETAINER 3
36 07660-00202 BARREL WASHER 2
37 07667-00207 BARREL NUT 1
38 70500-02001 BARREL 1
39 70500-02002 SEAL SPRING GUIDE 1
40 70500-02003 BARREL SPRING RETAINER 1
41 70500-02004 BARREL SPRING 1
42 70500-02005 SPACER 1
43 70500-02006 BODY 1
44 70500-02007 PISTON GUIDANCE TAPE - LONG 1
45 70500-02008 PISTON GUIDANCE TAPE - SHORT 1
ORIGINAL INSTRUCTION ENGLISH

12
ITEM PART NUMBER DESCRIPTION QTY.
46 70500-02009 PISTON 1
47 70500-02010 TAIL JAW HOUSING 1
48 70500-02011 BANJO 1
49 70500-02012 FRONT CYLINDER 1
50 70500-02014 LOCKNUT 1
51 70500-02015 PISTON NUT 1
52 70500-02016 BUFFER STOP 3
53 70500-02018 TURRET 1
54 70500-02019 JAW HOUSING 1
55 70500-02020 FRONT PISTON ROD 1
56 70500-02021 END STOP 1
ENGLISH ORIGINAL INSTRUCTION

13
7. SAFETY DATA
7.1 HYSPIN VG32 OIL SAFETY DATA
First Aid
SKIN:
Unlikely to cause harm to the skin on brief or occasional contact but prolonged or exposure may lead to dermatitis.
Wash skin thoroughly with soap and water as soon as reasonably practicable. Remove heavily contaminated clothing and
wash underlying skin.
Launder contaminated clothing.
ORAL:
Unlikely to cause harm if accidentally swallowed in small doses, though larger quantities may cause nausea and diarrhea.
If contamination of the mouth occurs, wash out thoroughly with water.
Except as adeliberate act, the ingestion of large amounts of product is unlikely. If it should occur, do not induce vomiting;
obtain medical advice.
Take person to nearest medical centre.
EYES:
Unlikely to cause more than transient stinging or redness if accidental eye contact occurs.
Wash eyes thoroughly with copious quantities of water, ensuring eyelids are held open. Obtain medical advice if any pain or
redness develops or persists.
Disposal:
Remove all spills with inert absorbent material. Ventilate spill area. Place contaminated materials in adisposable container
and dispose in amanner consistent with local regulations.
Protecting the Environment:
Separate collection. This product must not be disposed of with normal waste. Should you nd one day that your product
needs replacement, or if it is of no further use to you, do not dispose of it with regular waste.
Make this product available for separate collection. Separate collection of used products and packaging allows materials to
be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for
raw materials. Local regulations may provide for separate collection of electrical products, at municipal waste sites or by the
retailer when you purchase anew product. You can check the location of your nearest authorized repair agent by contacting
your local STANLEY Engineered Fastening oce at the address indicated in this manual. Alternatively, alist of authorized
repair agents and full details of our after-sales service and contacts are available on the Internet at:
www.StanleyEngineeredFastening.com
Fire:
FLASH POINT: 200°C.
Extinguish with dry, chemical, foam or carbon dioxide. Do not enter conned space without self-contained breathing
apparatus.
Handling:
Use barrier cream or oil resistant gloves.
Storage:
Undercover and consistent with local regulations for inammable material.
7.2 MOLYLITHIUM GREASE EP 3753 - SAFETY DATA
Grease can be ordered as asingle item, the part number is shown in the Service Kit page 8.
FIRST AID
SKIN:
As the grease is completely water resistant it is best removed with an approved emulsifying skin cleaner.
INGESTION:
Ensure the individual drinks 30ml Milk of Magnesia, preferably in acup of milk.
EYES:
Irritant but not harmful. Irrigate with water and seek medical attention.
FIRE
FLASH POINT: Above 220°C.
Not classied as ammable.
Suitable extinguishing media: CO2, Halon or water spray if applied by an experienced operator.
ORIGINAL INSTRUCTION ENGLISH

14
ENVIRONMENT
Scrape up for incineration or disposal on approved site.
HANDLING
Use barrier cream or oil resistant gloves
STORAGE
Away from heat and oxidising agent.
7.3 MOLYKOTE® 111 GREASE - SAFTEY DATA
Grease can be ordered as asingle item, the part number is shown in the Service Kit page 8.
FIRST AID
SKIN:
No rst aid should be needed.
INGESTION:
No rst aid should be needed.
EYES:
No rst aid should be needed.
INHALATION:
No rst aid should be needed.
FIRE
FLASH POINT: Above 101.1°C. (closed cup)
Explosive Properties: No
Suitable Extinguishing Media: Carbon Dioxide Foam, Dry Powder or ne water spray. Water can be used to cool re exposed
containers.
ENVIRONMENT
No adverse eects are predicted.
HANDLING
General ventilation is recommended. Avoid eye contact.
STORAGE
Do not store with oxidizing agents. Keep container closed and store away from water or moisture.
ENGLISH ORIGINAL INSTRUCTION

15
8. EC DECLARATION OF INCORPORATION FOR PARTLY COMPLETED
MACHINERY
We, Stanley Engineered Fastening, Stanley House, Works Road, Letchworth Garden City, Hertfordshire, SG6 1JY
UNITED KINGDOM, declare under our sole responsibility that the product:
Description: 70501 Hydro-Pneumatic Repetition Module Assembly
Model: 70501
to which this declaration relates is in conformity with the following harmonized standards:
ISO 12100:2010 ES100118-rev 17:2017
EN ISO 11148-1:2011
EN ISO 4413:2010
Technical documentation is compiled in accordance with Annex VII section B, in accordance with the following Directive:
2006/42/EC The Machinery Directive (Statutory Instruments 2008 No 1597 - The Supply of Machinery (Safety) Regulations
refers).
All relevant basic safety and health protection requirements of Directive 2006/42/EC are complied with up to the interface
cell described in the operating instructions, Section 3 and 4.
The undersigned makes this declaration on behalf of STANLEY Engineered Fastening
A. K. Seewraj
Director of Engineering, UK
Avdel UK Limited, Stanley House, Works Road, Letchworth Garden City, Hertfordshire,
SG6 1JY UNITED KINGDOM
Place of Issue: Letchworth Garden City, UK
Date of Issue: 04-10-2021
The undersigned is responsible for compilation of the technical le for products sold in the European Union and makes this
declaration on behalf of Stanley Engineered Fastening.
Matthias Appel
Team Leader Technical Documentation
Stanley Engineered Fastening, Tucker GmbH, Max-Eyth-Str.1,
35394 Gießen, Germany
This machinery is in conformity with
Machinery Directive 2006/42/EC
you need to confirm latest information.
ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affiliates.
The names and logos of other companies mentioned herein may be trademarks of their respective owners.
STANLEY Engineered Fastening
4 Shelter Rock Lane
Danbury, Connecticut,
United States, 06810
Tel. [phone]
Fax [phone]
ProSet®PB2500CC Collar Cropper sizes 1/4 ” and 5/16”
Battery Power Tool
Manual Number Issue C/N
65124-00001 A20203
© 2019 Stanley Black & Decker, Inc.
Avdel®, Avex®, Avibulb®, Avinox®, Avseal®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,
Data shown is subject to change without prior notice as a result of continuous product development and
improvement policy.Your local STANLEY Engineered Fastening representative is at your disposal should
INSTRUCTION AND
SERVICE MANUAL
Holding your world together®
Find your closest STANLEY Engineered Fastening location on
www.stanleyengineeredfastening.com/contact
For an authorized distributor nearby please check
www.stanleyengineeredfastening.com/econtact/distributors
ORIGINAL INSTRUCTION ENGLISH

16
9. UK DECLARATION OF INCORPORATION FOR PARTLY COMPLETED
MACHINERY
We, Stanley Engineered Fastening, Stanley House, Works Road, Letchworth Garden City, Hertfordshire, SG6 1JY
UNITED KINGDOM, declare under our sole responsibility that the product:
Description: 70501 Hydro-Pneumatic Repetition Module Assembly
Model: 70501
to which this declaration relates is in conformity with the following designated standards:
ISO 12100:2010 ES100118-rev 17:2017
EN ISO 11148-1:2011
EN ISO 4413:2010
Technical documentation is compiled in accordance with the Supply of Machinery (Safety) Regulations 2008, S.I. 2008/1597
(as amended).
All relevant basic safety and health protection requirements of the Supply of Machinery (Safety) Regulations 2008, S.I.
2008/1597 (as amended) are complied with up to the interface cell described in the operating instructions, Section 3 and 4.
The undersigned makes this declaration on behalf of STANLEY Engineered Fastening
A. K. Seewraj
Director of Engineering, UK
Avdel UK Limited, Stanley House, Works Road, Letchworth Garden City, Hertfordshire,
SG6 1JY UNITED KINGDOM
Place of Issue: Letchworth Garden City, UK
Date of Issue: 04-10-2021
This machinery is in conformity with
Supply of Machinery (Safety) Regulations 2008,
S.I. 2008/1597 (as amended)
you need to confirm latest information.
ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affiliates.
The names and logos of other companies mentioned herein may be trademarks of their respective owners.
STANLEY Engineered Fastening
4 Shelter Rock Lane
Danbury, Connecticut,
United States, 06810
Tel. [phone]
Fax [phone]
ProSet®PB2500CC Collar Cropper sizes 1/4 ” and 5/16”
Battery Power Tool
Manual Number Issue C/N
65124-00001 A20203
© 2019 Stanley Black & Decker, Inc.
Avdel®, Avex®, Avibulb®, Avinox®, Avseal®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,
Data shown is subject to change without prior notice as a result of continuous product development and
improvement policy.Your local STANLEY Engineered Fastening representative is at your disposal should
INSTRUCTION AND
SERVICE MANUAL
Holding your world together®
Find your closest STANLEY Engineered Fastening location on
www.stanleyengineeredfastening.com/contact
For an authorized distributor nearby please check
www.stanleyengineeredfastening.com/econtact/distributors
ENGLISH ORIGINAL INSTRUCTION

17
10.PROTECT YOUR INVESTMENT!
Stanley® Engineered Fastening BLIND RIVET TOOL WARRANTY
STANLEY® Engineered Fastening warrants that all power tools have been carefully manufactured and that they will be free
from defect in material and workmanship under normal use and service for aperiod of one (1) year.
This warranty applies to the rst time purchaser of the tool for original use only.
Exclusions:
Normal wear and tear.
Periodic maintenance, repair and replacement parts due to normal wear and tear are excluded from coverage.
Abuse & Misuse.
Defect or damage that results from improper operation, storage, misuse or abuse, accident or neglect, such as physical
damage are excluded from coverage.
Unauthorized Service or Modication.
Defects or damages resulting from service, testing adjustment, installation, maintenance, alteration or modication in any
way by anyone other than STANLEY® Engineered Fastening, or its authorized service centres, are excluded from coverage.
All other warranties, whether expressed or implied, including any warranties of merchantability or tness for purpose are
hereby excluded.
Should this tool fail to meet the warranty, promptly return the tool to our factory authorized service centre location nearest
you. For alist of STANLEY® Engineered Fastening Authorized Service Centres in the US or Canada, contact us at our toll free
number [phone].
Outside the US and Canada, visit our website www.StanleyEngineeredFastening.com to nd your nearest STANLEY
Engineered Fastening location.
STANLEY Engineered Fastening will then replace, free of charge, any part or parts found by us to be defective due to faulty
material or workmanship and return the tool prepaid. This represents our sole obligation under this warranty.
In no event shall STANLEY Engineered Fastening be liable for any consequential or special damages arising out of the
purchase or use of this tool.
Register Your Blind RivetTool online.
To register your warranty online, visit us at
https://www.stanleyengineeredfastening.com/support/warranty-registration-form
Thank you for choosing aSTANLEY® Engineered Fastening’sStanley Assembly Technologies Brand tool.
ORIGINAL INSTRUCTION ENGLISH

18
ENGLISH ORIGINAL INSTRUCTION

19
©2021 STANLEY Black & Decker
  .
       /      
 (  )       STANLEY Engineered
Fastening.      ,       
 . STANLEY Engineered Fastening       
     .      , 
   STANLEY Engineered Fastening.  , STANLEY Engineered Fastening      
,        .
     .  , STANLEY Engineered Fastening   
         ,     .
STANLEY Engineered Fastening       ,   ,  
 .  ,  ,   ..,   STANLEY
Engineered Fastening,       ,       
 .

1.   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.1    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
1.2    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
1.3   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
1.4     . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
1.5    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.6    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.7    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.8        . . . . . . . . . . .22
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.1  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.2    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.3    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.1   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
5.2   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
5.3  /  500 000  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
5.4   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
5.5   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
5.6   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
5,7     . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
6.       . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.1   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
6.2   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
7.    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
7.1     HYSPIN VG32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
7.2   EP 3753 -    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
7.3 MOLYKOTE® 111  -    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
8. EC       . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9.          . . . . . . . . . . . 33
10.   ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
    

20
          ,     
,        .
           .   
       .
          , 
, , ,  .       .
          
    .
1.   
 -      . ,    
 .
!ОПАСНОСТ:    ,     ,     
 .
!ПРЕДУПРЕЖДЕНИЕ:    ,     ,     
  .
!ВНИМАНИЕ:    ,     ,      
 .
!ВНИМАНИЕ:           ,  
  ,     .
            
 .
      ,    
.    ,         
       .
                   
.      ,    .
       .
1.1    
•           ,
, , ,       .
         .
•       ,    .
•               STANLEY
Engineered Fastening.
•   ,   ,   .
•   .          
   .     ,     
          .
•     ;    .
•   ,   .
•  ,         ,   
  ,         .  ,
 ,   .      , 
.
    