Stanley Fatmax sl10leds User manual

4. Plug the 120V AC/USB Charging Adapter into a (powered) standard North American 120

volt 60Hz outlet. The Battery/Charge Status LED Indicator will light or flash in one of three

colors (as described in the “Reading the Battery/Charge Status LED Indicator” section) to

indicate the charging status.

5. Charge until the Battery/Charge Status LED Indicator lights green.

6. When charging is complete, first unplug the AC/USB Charging Adapter from the power

source, then disconnect the USB Charging Cable from the adapter and the light. Store the

adapter and cable in a safe place.

Charging/Recharging Using the 12V DC/USB Charging

Adapter

1. Make sure the On/Off Trigger and the USB Power Button are both turned off (the light is

not lit and the Battery/Charge Status LED Indicator inside the translucent ring around the

USB port at the back of the unit is not lit).

2. Insert the USB Charging Cable into the USB port on the light.

3. Insert the other end of the USB charging cable into the 12V DC/USB Charging Adapter.

4. Insert the 12V DC/USB Charging Adapter into the 12 volt DC accessory outlet of a vehicle

or other functioning 12 volt DC power source. The LED indicator on the 12V DC/USB

Charging Adapter will light green when it is properly plugged into the 12 volt DC power

source. The Battery/Charge Status LED Indicator will light or flash in one of three colors

(as described in the “Reading the Battery/Charge Status LED Indicator” section) to indicate

the charging status.

Note: Some vehicles require that the ignition be switched to the accessory position in order to power

the accessory outlet.

5. Charge until the Battery/Charge Status LED Indicator lights green.

6. When charging is complete, first unplug the 12V DC/USB Charging Adapter from the 12

volt DC power source, then disconnect the USB Charging Cable from the adapter and the

light. Store the adapter and cable in a safe place.

Charging/recharging using the USB Charging Cable and a

Device with a USB Power Port (not supplied)

1. Make sure the On/Off Trigger and the USB Power Button are both turned off (the light is

not lit and the Battery/Charge Status LED Indicator inside the translucent ring around the

USB port at the back of the unit is not lit).

2. Insert the USB Charging Cable into the USB port on the light.

3. Insert the other end of the USB Charging Cable into a device’s functional USB power

port. The Battery/Charge Status LED Indicator will light or flash in one of three colors (as

described in the “Reading the Battery/Charge Status LED Indicator” section) to indicate

the charging status.

4. Charge until the Battery/Charge Status LED Indicator lights green.

5. When charging is complete, disconnect the USB Charging Cable from the device’s USB

power port and the light. Store the cable in a safe place.

OPERATING THE SPOTLIGHT

IMPORTANT: If the USB Power Button is pressed to turn on the USB Port when the unit is

operating in High light mode, the unit will switch automatically to Low light mode.

If the light’s battery voltage is nearly low, the unit will switch automatically to Low light mode

even if High light mode has been selected.

If the light’s battery voltage is low, the built-in low voltage protection will activate after a short

period of operation, then the unit will automatically shut down. Recharge the battery before

continuing use.

The On/Off Trigger turns the unit on and off, and is also used to choose either the high or low

brightness setting.

DO NOT OPERATE WHILE CHARGING.

Disconnect the charging cable or adapter, then select the light mode as follows:

• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.

• Press the On/Off trigger again

within 5 seconds

to use the spotlight in its low (dimmest)

setting.

• Press the On/Off trigger a third time to turn the unit off.

• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.

• Press the On/Off trigger again

after 5 seconds

to turn the unit off.

Note: The Battery/Charge Status LED Indicator will light in one of three colors (as described in the “Reading

the Battery/Charge Status LED Indicator” section) to indicate the battery status.

Using the Emergency Red Lens

The Emergency Red Lens snaps into place directly over the Rubber Bezel.

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY

DAMAGE:

• Never touch the Emergency Red Lens or place the light with an attached Red

Emergency Lens face down on any surface while it is operating.

• Never use the Red Emergency Lens on the spotlight if it is damaged.

• Always detach the Red Emergency Lens from the spotlight and store it properly when it is

not in use.

Using the Swing-up Stand

Lift the Swing-up Stand up, invert the unit and set it upon a flat, stable surface

for hands-free operation.

OPERATING THE LIGHT’S USB PORT

IMPORTANT: If the USB port is in use, the light will only operate in Low light mode.

The light’s USB port provides 5 volts/1A of DC power to an external USB powered device.

1. Disconnect the charging adapter or cable and make sure the light is turned off.

2. Press the USB Power Button to power on the USB port. The Battery/Charge Status LED

Indicator will light or flash in one of three colors (as described in the “Reading the Battery/

Charge Status LED Indicator” section) to indicate the internal battery status.

3. Simply plug the USB device into the light’s USB port and operate normally.

4. Press the USB Power Button again to turn off the USB port. Make sure the USB Power

Button is in the off position when the unit is being recharged or stored.

OPERATING THE 120V AC/USB CHARGING ADAPTER’S

USB PORT

Plug the 120V AC/USB Charging Adapter into a (powered) standard North American 120 volt

60Hz outlet. Then simply plug the USB device into the USB outlet and operate normally.

Always plug the 120V AC/USB Charging Adapter to the standard North American

120 volt 60Hz outlet before plugging any devices into it.

OPERATING THE 12V DC/USB CHARGING ADAPTER’S

USB PORT

Plug the 12V DC/USB Charging Adapter into a vehicle’s 12 volt DC accessory outlet or other

functioning 12 volt DC power source. The LED indicator on the 12V DC/USB Charging Adapter

will light green to indicate that it is properly connected. Then simply plug the USB device into

the USB outlet and operate normally.

Note: Some vehicles require that the ignition be switched to the accessory outlet position in order to power

the accessory outlet

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures.

When the unit is not in use, we recommend that the battery is charged at least every 3 to 6

months.

Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the

spotlight unit with a soft cloth.

Except for the fuse in the 12V DC/USB Charging Adapter, there are no user-replaceable parts.

Periodically inspect the condition of adapters, connectors and wires. Contact the manufacturer

to replace any components that have become worn or broken.

Battery replacement/disposal

BATTERY REPLACEMENT

The battery should last the service life of the unit. Service life is dependent on a number

of factors including but not limited to the number of recharge cycles, and proper care and

maintenance of the battery by the end user. Contact manufacturer for any information you

may need.

SAFE BATTERY DISPOSAL

Contains a lithium battery, which must be disposed of properly.

Recycling is required. Failure to comply with local, state and federal

regulations can result in fines, or imprisonment.

Please recycle.

WARNINGS:

• Do not dispose of the battery in fire as this may result in an explosion.

• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to

prevent shorting (shorting can result in injury or fire).

• Do not expose battery to fire or intense heat as it may explode.

Replacing the Fuse in the 12V DC/USB Charging Adapter

2A FUSE

CENTER CONTACT

END CAP

1. Unscrew the end cap counterclockwise

and remove.

2. Remove center contact and fuse.

3. Check fuse with a continuity checker.

4. If blown, locate a replacement

2 amp fuse.

5. Replace the fuse, center contact and

end cap.

6. Screw end cap clockwise until it is finger

tight – DO NOT OVER-TIGHTEN.

7. Test for proper operation of the 12 Volt

DC/USB Charging Adapter.

TROUBLESHOOTING

The Spotlight will not charge

• Check that the Spotlight and the USB port are all turned off.

• Check that the USB Charging Cable is properly connected to either the 12V DC/USB Charging

Adapter or the 120V AC/USB Charging Adapter, and to the Spotlight.

• Check the connection to the AC or DC power source. Make sure there is good contact.

• Confirm that there is functioning AC or DC current.

• Check the plug fuse in the 12V DC/USB Charging Adapter. Replace the fuse following the

instructions in this manual, if necessary.

• The unit may have shut down to protect the battery from overheating after a long period of

operation or charging. Unplug the charging adapter from the power source and disconnect

the USB charging cable from the spotlight. Allow the spotlight to cool down for a period

before resuming charging.

The Spotlight will not operate

• Make sure the On/Off Trigger has been pressed to turn the Spotlight on.

• The internal battery may be completely discharged. Charge the unit following the directions

given in this manual.

• If the ambient temperature is too hot or too cold the Spotlight will not operate.

The Spotlight’s USB Port will not operate

• Make sure the cable and/or adapter is disconnected from any live AC or DC power source.

• Make sure the On/Off Trigger is turned off.

• Make sure the USB Power Button is pressed to turn the USB port on.

• Make sure the rating of equipment plugged into the light’s USB port does not exceed 1A

continuous.

• The internal battery may be completely discharged. Charge the unit following the directions

given in this manual.

The 120V AC/USB Charging Adapter’s USB Port will not operate

• Make sure you have live AC power to the outlet the 120V AC/USB charging adapter is

plugged into.

• Make sure the rating of equipment plugged into the charging adapter’s USB Port does not

exceed 1A continuous.

• Some household USB-powered electronics will not operate with this USB Port. Check the

manual of the corresponding electronic device to confirm that it can be used with this type

of USB Port.

The 12V DC/USB Charging Adapter’s USB Port will not operate /

LED Indicator does not come on

• Check the connection to the 12 volt DC power source. Make sure there is good contact.

• Confirm there is functioning DC current.

• Check the plug fuse in the 12V DC/USB Charging Adapter. Replace the fuse following the

instructions in this manual, if necessary.

• Make sure the rating of equipment plugged into the Charging Adapter’s USB Port does not

exceed 2.1A continuous.

• Some household USB-powered electronics will not operate with this USB Port. Check the

manual of the corresponding electronic device to confirm that it can be used with this type

of USB port.

ACCESSORIES

Recommended accessories for use with this unit may be available from the manufacturer. If you

need assistance regarding accessories, please contact manufacturer at 1-877-571-2391.

The use of any accessory not recommended for use with this appliance could be hazardous.

SERVICE INFORMATION

Whether you need technical advice, repair, or genuine factory replacement parts, contact the

manufacturer at 1-877-571-2391.

ONE-YEAR LIMITED WARRANTY

The manufacturer warrants this product against defects in materials and workmanship for a

period of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser

(“Warranty Period”).

If there is a defect and a valid claim is received within the Warranty Period, the defective

product can be replaced or repaired in the following ways: (1) Return the product to the

manufacturer for repair or replacement at manufacturer’s option. Proof of purchase may be

required by manufacturer. (2) Return the product to the retailer where product was purchased

for an exchange (provided that the store is a participating retailer). Returns to retailer should be

made within the time period of the retailer’s return policy for exchanges only (usually 30 to 90

days after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from

normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized

use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance

for the product.

This warranty gives you, the original retail purchaser, specific legal rights and you may have

other rights which vary from state to state or province to province. This product is not intended

for commercial use.

Please visit our website www.baccusglobal.com/register to register your new Baccus Global LLC

product and to be kept up to date on new products and special offers.

SPECIFICATIONS

Spotlight

Bulb: 10 watt LED

Battery: Lithium, 3.6V DC

Input: 5V DC, 1A (120V AC/USB Charging Adapter) or

2.1A (12V DC/USB Charging Adapter)

USB Output: 5V DC, 1A

12V DC/USB Charging Adapter (Conforms to UL STD. 2089)

(Optional Accessory)

Input: 12V DC, 1.1A

Output: 5V DC, 2.1A

Fuse: 2A

120V AC/USB Charging Adapter (Conforms to UL STD. 62368-1)

(Optional Accessory)

Input: 120V AC, 60Hz, 6.7W

Output: 5V DC, 1A

STANLEY®AND THE STANLEY®LOGO ARE

REGISTERED TRADEMARKS OF STANLEY BLACK +

DECKER INC. OR ONE OF ITS AFFILIATES, AND ARE

USED UNDER LICENSE.

Imported by Baccus Global LLC,

621 NW 53rd St., Suite 450, Boca Raton, FL 33487

www.baccusglobal.com 1-877-571-2391

RD030121

LITHIUM LED SPOTLIGHT

INSTRUCTION MANUAL

SL10LEDS

14 15

SAVE THIS INSTRUCTION MANUAL FOR FUTURE

REFERENCE.

Baccus Global LLC, Boca Raton, FL 33487

1-877-571-2391

Optional 120V AC/USB Charging Adapter: This device complies with part 15 of the FCC

rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If equipment does

cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not approved by the party responsible for compliance could void

user’s authority to operate the equipment.

SAFETY GUIDELINES /

DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, may result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

Used without the word, indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may

result in property damage.

RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety

precautions should always be followed to reduce the risk of personal injury. Improper

operation, maintenance or modification of tools or equipment could result in serious injury and

property damage. There are certain applications for which tools and equipment are designed.

Manufacturer strongly recommends that this product NOT be modified and/or used for any

application other than for which it was designed. Read and understand all warnings and

operating instructions before using any tool or equipment.

READ ALL INSTRUCTIONS

WARNING: READ ALL INSTRUCTIONS BEFORE OPERATING THIS SPOTLIGHT.

Failure to follow all instructions listed below may result in electric shock, fire and/

or serious injury.

IMPORTANT SAFETY

INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS

WARNING – RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO

PERSONS – when using electrical appliances, basic precautions should always be

followed, including the following:

• LED gets HOT quickly!

• Do not touch the LED at any time when operating.

• Only contact trigger when turning on.

• Do not touch hot lens or enclosure.

• Do not remain in light if skin feels warm.

• Do not operate the spotlight with a missing or damaged lens or enclosure.

WARNING – WHEN USING ELECTRICAL APPLIANCES, basic precautions should

always be followed, including the following:

• The spotlight and the supplied charging adapters are not toys and cannot be played with

as toys. To reduce the risk of injury, close supervision is necessary when these units are used

near children.

• Use only attachments recommended or sold by the manufacturer.

WARNING – TO REDUCE THE RISK OF ELECTRIC SHOCK:

• Do not put the spotlight in water or other liquid. Do not place or store this light where it can

fall or be pulled into water or become wet.

• Charge indoors only. Do not expose charger to water or any other liquid.

• Do not clean this appliance with a water spray or the like.

• Use only the chargers supplied by the manufacturer to charge and recharge.

• When an extension cord is used:

– The marked rating of the detachable power supply cord or extension cord should be at

least as great as the electrical rating of this appliance.

– The cord should be arranged so that it will not drape over the countertop or tabletop

where it can be tripped over, snagged, or pulled on unintentionally (especially by

children).

– The extension cord should be kept dry and off the ground.

WARNING – FIRE HAZARD: Never contact combustible material to the lens or heat sink.

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

• All lights give off heat:

– Do not touch lens while operating.

– Keep combustibles away from spotlight lens. Extreme heat can cause fires.

– Never place the light face down on any surface when lit, charging or not in use. Never

store the light face down on any surface.

• Never look directly into the light or shine the light into another person’s eyes. Serious eye

injury could occur.

• Keep sharp objects away from lens — it is glass and can break.

• Do not immerse spotlight in water.

• Do not expose this unit to extremely high temperatures.

• Do not drop or throw spotlight. It contains glass and a lithium battery.

• Use only with either the AC or DC charging adapter and/or the USB charging cable that are

provided with unit. Plug in the charging cable at the light first, then plug into the charging

source.

• After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes

before use.

• Do not crush, cut, pull or expose charging adapter cords to extreme heat.

• Position charging adapter cords so they do not become entangled or become a safety hazard.

Keep charging adapter cords away from sharp edges.

• Use in a dry location only.

• Except for the fuse in the 12VDC Charging Adapter, there are no user-serviceable parts inside.

Do not attempt to disassemble any other parts of the unit.

• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting.

• Do not attempt to charge the unit if the charger or cord is damaged – return the charger to

manufacturer for repair or replacement.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM BATTERIES

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR

INJURY TO PERSONS OR PROPERTY:

Lithium batteries are small, compact and ideal for providing long-lasting power to this unit.

However, they must be used and charged properly. Improper use can result in serious injury,

fire, or death.

• Lithium batteries can explode in the presence of a source of ignition. Do not use the product

in the presence of an open flame.

• Do not place this lithium battery powered unit in fire or apply heat to it.

• Do not subject this lithium battery powered unit to strong impacts or shocks. The battery in

this unit contains safety and protection devices which, if damaged, may cause the battery to

generate heat, rupture or ignite.

• Do not expose this lithium battery powered unit to water or salt water, or allow the battery

to get wet.

• Avoid storing this lithium battery powered unit in the basement, bathroom or other areas of

the house that are or may become wet or humid or where moisture may concentrate.

• Do not leave this lithium battery powered unit in direct sunlight, or use or store the unit inside

cars in hot weather. Doing so may cause the battery to generate heat, rupture, or ignite.

Using the battery in this manner may also result in a loss of performance and a shortened

life expectancy.

• Never charge this unit near heat or flammable objects.

• NEVER THROW WATER ON A BURNING LITHIUM BATTERY! If a lithium

battery does catch on fire, it will burn even more violently if it comes in contact

with water or even moisture in the air. A fire extinguisher must be used.

Battery Charging and Capacity

This unit is delivered in a partially charged state – you must fully charge it before using it for

the first time.

When stored at room temperature with a full charge, lithium batteries will begin to discharge

from the time they are manufactured, even when unused. Deep discharges also decrease their

capacity. Battery life can be extended by the following:

• Charge battery to full capacity before storage.

• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).

• Never discharge the battery fully.

• Charge after each use.

• Always charge at least once every 3-6 months if not in frequent use to prevent overdischarge.

Transportation of Lithium Batteries

• Always check all applicable local, national, and international regulations before transporting a

unit containing a lithium battery.

• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be specifically

limited or prohibited.

INSTRUCTIONS PERTAINING TO THE 12V DC/USB

CHARGING ADAPTER

NOTICE:

• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.

• The 12V DC Charging Adapter must only be connected to batteries with a nominal output

voltage of 12 volts. The unit will not operate from a 6 volt battery and will sustain permanent

damage if connected to a 24 volt battery.

• Always connect the 12V DC Charging Adapter to the 12 volt DC power source before plugging

any devices into it.

INSTRUCTIONS PERTAINING TO THE USB PORTS

NOTICE:

• IMPORTANT: Some household USB-powered electronics will not operate with the USB ports

provided with this device. Check the manual of the corresponding electronic device to confirm

that it can be used with this type of USB port.

• The USB ports do not support data communication. They only provide power to an

external USB powered device (5V DC/1A using the USB Port on the Spotlight or AC/USB

Charging Adapter or 5V DC/2.1A using the USB Port on the DC/USB Charging Adapter). Make

sure the rating of equipment plugged into the USB Port does not exceed the amperage stated.

• Always connect the appropriate charging adapter to either the 120 volt AC or 12 volt DC

power source before plugging any devices into it.

• Do not attach USB hubs allowing connection of multiple personal electronic devices to any of

the USB ports on the charging adapters.

SAVE THESE INSTRUCTIONS

INTRODUCTION

Congratulations on purchasing your new

Stanley®Lithium LED Spotlight

.Read this

Instruction Manual and follow the instructions carefully before using your new

spotlight.

FEATURES

1. Rubber Bezel

2. Heat Sink

3. Swing-up Stand

4. On/Off Trigger

5. Pistol Grip Handle

6. Battery/Charge Status LED Indicator

7. USB Port (for use with USB Charging

Cable and charging adapters)

8. USB Power Button

9. Emergency Red Lens (Optional Accessory)

10. USB Charging Cable (for use with

120V AC/USB and 12V DC/USB Charging

Adapters)

11. 12V DC/USB Charging Adapter (Optional

Accessory)

12. 12V DC/USB Charging Adapter LED

Indicator

13. 12V DC/USB Charging Adapter USB Port

(Optional Accessory)

14. 120V AC/USB Charging Adapter (Optional

Accessory)

15. 120V AC/USB Charging Adapter USB Port

(Optional Accessory)

READING THE BATTERY/CHARGE STATUS LED INDICATOR

The Battery/Charge Status LED Indicator is a translucent ring around the USB Port at the back of

the unit. It lights or flashes in three colors to indicate the following:

When Charging:

Green: Battery is in a fully charged state.

Green (flashing): Battery is in a high partially charged state.

Orange (flashing): Battery is in a low partially charged state.

Red (flashing): Battery needs to be recharged.

Red (flashing rapidly): The battery of the unit is overheated due to extensive use or

recharging. The charging process will stop at this stage and will automatically resume after a

cool down period.

When Operating (once the light has been turned on or the USB

Power Button has been pressed):

Green: Battery is operating at full voltage.

Orange: Battery is operating at partial voltage.

Red: Battery is operating at low voltage, and should be recharged or the built-in low voltage

protection will be activated and the unit will automatically shut down shortly.

Red (flashing rapidly): The battery of the unit is overheated (due to extensive use

or recharging), or is too cold (the ambient temperature has dropped below –20°C). To avoid

damage, the unit should be shut off at this stage and allowed to either cool down or warm up

to normal operating temperatures before resuming use.

CHARGING/RECHARGING THE SPOTLIGHT

This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use

until the Battery/Charge Status LED Indicator lights green.

Recharge after each use until the Battery/Charge Status LED Indicator lights green.

IMPORTANT: When the unit is not in use, we recommend that the battery is charged

at least every 3 to 6 months.

CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

• Never place the light face down on any surface when charging.

• Make sure the light and the USB port are turned off during recharging, as using these features

can slow the recharging process.

• Failure to keep the battery charged will cause permanent damage and result in poor

performance.

NOTE: The USB Power Button does not operate the light, only the USB Power Port. The

light cannot be charged when the USB Power Port is on. Make sure the USB Power

Button is turned off before charging

Charging/Recharging Using the 120V AC/USB Charging

Adapter

1. Make sure the On/Off Trigger and the USB Power Button are both turned off (the light is

not lit and the Battery/Charge Status LED Indicator inside the translucent ring around the

USB port at the back of the unit is not lit).

2. Insert the USB Charging Cable into the USB port on the light.

3. Insert the other end of the USB Charging Cable into the 120V AC/USB Charging Adapter.

SL10LEDS_ManualENSP_030121.indd 1SL10LEDS_ManualENSP_030121.indd 1 3/1/2021 9:56:39 AM3/1/2021 9:56:39 AM