Star SE06E1FB User manual

0(min) 35(max)
35( ma x) 3 0 25 20 15 10 5 5 10 15 20 25 30
Electric Height Adjustable Desk Frame
SE06E1FB
Attaching Side Brackets
Version June 2020
• Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent
scratches.
• Carefully place the tabletop (not included) upside down on the blanket.
• Place the crossbar and side brackets on the top.
• Attach the side brackets to the end of the crossbar . (This step doesn't require the use of the
screws.)
• Insert one lifting column into one end of the crossbar with the head of the lifting column facing inward.
Make sure the mounting holes on the lifting column completely align with the screw holes on the crossbar.
• Fix the lifting column with crossbar using 4 screws with the Allen wrench .
• Repeat the same process to assemble the other lifting column.
• Place the foot on the bottom of the lifting column. Align the mounting holes on the foot with the screw
holes on the lifting column.
• Fix the foot using 4 screws with the Allen wrench .
• Repeat the same process to assemble the other foot.
• Use a drill to make mounting holes on the backside of the tabletop through the 8 mounting holes on
the side brackets.
Note: The drawings of both of the crossbar and side brackets are the backside of the components.
Please make sure the crossbar and side brackets keep facing down while installation, which is
convenient for the further steps.
Note: The depth of the mounting holes should be over 10mm and the diameter should be less than 3mm.
Loosen the hex head screws that fix the adjustable junction,
but don't completely take out the screws.
Retighten all the hex head screws to finish the adjustment.
• Ensure that the frame is placed in the center of the table.
• Then adjust the frame to suit the size of the tabletop.
When adjusting the frame position, please make sure it doesn't exceed the range of silk screen printing
on the inner crossbar.
Shipping
Blanket
Drill
A
B
1Drilling Mounting Holes 3
2Adjusting the Frame
S-I
S-I
4Assembling the Lifting Columns
5Assembling the Feet
S-A
S-I
C
S-B
S-I
D
A (x1)
crossbar
F (x1)
control box
G (x1)
power plug
H (x1)
cable management tray
I (x2)
tray hanger
J (x1)
controller
B (x2)
side bracket
C (x2)
lifting column
D (x2)
foot
E (x1)
fixing plate
S-A (x8)
hex head screw
S-E (x2)
phillips head screw
S-F (x4)
phillips head screw
S-G (x3)
cable clip
S-H (x10)
anti-vibration pad
S-I (x1)
allen wrench
S-B (x8)
hex head screw
S-C (x10)
phillips head screw+1 spacer
S-D (x2)
phillips head screw
Scan the QR Code™ below
for more info about this product:
Do not exceed the maximum rated weight
specified. Otherwise, serious injury or
property damage may occur.
125kg
(275lbs)
A
A
B
B
S-A S-I
S-B S-I
C
D

• Align the mounting holes on the fixing plate with the screw holes as shown.
• Attach the fixing plate on the center of the crossbar with 2 screws using a Phillips
screwdriver.
• Align the mounting holes on the tray hangers with the screw holes on the cable management tray.
• Assemble the tray hangers to the cable management tray with 4 screws from below using
a Phillips screwdriver.
• Attach the anti-vibration pad to the surface of the crossbar on the ten positions as shown.
• There are two adjustable foot pads under each foot. If the floor isn't even, simply turn the pad to adjust
the level to make the desk stable.
Connect the desk to power.
You can now use the sit-stand desk.
Note: We have another manual of the digital controller for
detailed instruction. Please check the Digital Control Panel
For Electric Height Adjustable Desk User Guide.
• Align the previously drilled screw holes with the mounting holes on the crossbar. Insert and tighten the
4 screws from below.
• Repeat the same process to assemble the other side of the tabletop.
• Attach the controller to the tabletop with 2 screws using a driller.
• Stick the adhesive cable clip under desk to organize cords.
• The arrow on the fixing plate indicates the direction of sliding in the control box. Follow the direction of
the arrow to mount the control box.
• Slide the control box to the center of fixing plate.
The fixing plate can be attached to either of the right side and the left side.
• Turn over the desk frame with the crossbar facing up. At least two people are required when turning
over the desk frame. If only one person turns over the desk frame, serious bodily injuries might occur.
• Connect the cords, control box and motors.
Hang the cable management tray on
the crossbar as shown.
Note: The arrow on the fixing plate indicates the direction of sliding in the control box. Follow the direction
of the arrow to mount the control box in the next step.
Tip: Use a bubble level to check if the tabletop is even.
Note:
• Please make sure the slot on the control box is facing upward. There is no corresponding relation
between the motor ports and the lifting columns.
• The picture of the controller is for your reference only. Actual product may vary.
• Connect the two motor cords to the two ports
marked "M1" and "M2" (one on each side of the
control box).
• Insert the power plug in the port marked "AC".
• Connect the controller cord to the port marked
"HS".
Phillips
Screwdriver
Phillips
Screwdriver
Phillips
Screwdriver
Bubble Level
Assembling the Fixing Plate
6
8Assembling the Cable Management Tray
Level Adjustment
10
11 Height Adjustment
7Attaching the Control Box
CAUTION
M1&M2
AC
HS
1 2 9Assembling the Tabletop
Tighten the knobs on the tray hangers.
F
J
G
S-E
S-F
S-H
S-H
S-C
S-D
S-G
H
I
E
Drill
S-E
S-F
S-H
S-C
S-D
S-G
E
F
I
H
J
G