Ensure the weight of the equipment does not exceed the weight capacity of this product.
If the weight capacity is exceeded, personal injury or damage to the equipment are
possibilities. These products can support the following weight:
• RK119WALLV: Rev 01 to 02 - Up to 125 lbs / 56kg; Rev 03 or above - Up to 130 lbs / 59kg
• RK119WALLV2: Up to 130 lbs / 59kg
• RK219WALLV: Up to 125 lbs / 56kg
• RK319WALLV: Rev 01 to 02 - Up to 125 lbs / 56kg; Rev 03 or above - Up to 150 lbs / 68kg
• RK319WALLV2: Up to 150 lbs / 68kg
• RK419WALLV: Rev 01 to 02 - Up to 125 lbs / 56kg; Rev 03 or above - Up to 180 lbs / 81kg
• RK419WALLV2: Up to 180 lbs / 81kg
• RK519WALLV: Up to 198 lbs / 90kg
• RK619WALLV: Up to 200 lbs / 90kg
Ensure the type of wall structure and mounting hardware will properly support the
mounted equipment. Failure to do so might result in personal injury and/or equipment
damage. The wall or mounting structure should be capable of supporting at least four
times the weight of the mounted equipment.
Installation
Mount the Rack Bracket
The mounting holes are spaced 16 inches (2 inner holes) and 18.8 inches (4 outer holes)
apart. Test t the Rack Bracket on the surface to ensure proper t on the designated
location.
1. Mark the Mounting Points (x6) using the Mounting Holes (x6) on the Wall Bracket as
a Template.
2. Use the Wood Screws (x6) to fasten the Wall Bracket to the Mounting Surface.
The included screws are for wood surfaces only.
3. Install the M5 Square Cage Nuts onto the desired Square Cage Nut Holes where
the Equipment will be installed. Use a Cage Nut Tool if available or your preferred
installation method.
4. Use a Phillips Head Screwdriver to install the M5 Screws and secure the Equipment
onto the Mounting Rails.
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.
Warranty Information
This product is backed by a lifetime warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
