Stealth Tactical DORM Operator's manual
DORM SAFE
Dear Valued Customer,
Congratulations on the purchase of your Stealth Tactical Dorm Safe!
Here at Stealth, we pride ourselves on providing easy and simple solutions
for your everyday storage needs. You have taken a very important step in
protecting your most valuable possessions.
college dorm rooms
or RV’s where space is limited. It’s vertical design
If you have any questions regarding your Stealth Dorm Safe, please
contact Stealth Customer Service at (800) 827-7534.
FEATURES
DIAGRAM:
DIMENSIONS:
INCLUDED:
Full Steel Body
Card Reader
Electronic Keypad
Steel Hinge
Shelf Rubber
Lining
Floor Rubber
Lining
Half Shelves (3)
Steel Locking
Bolts (2)
Rear Access
Holes (2)
Security Cable
Attachment Hole
Turning Knob
Front
Battery
Compartment
Mounting
Holes (6)
Securing Slots
Safe Securing
Screw Holes (2)
MOUNTING
PLATE
Mounting Plate
Located Underneath
Dorm Safe
Mounting Plate
Securing Screws
Located Under
Floor Lining
Exterior:
20”h x 7”w x 14”d
Weight:
35 lbs
US Patent D617974
Electronic Lock: Standard 9V battery operated and easily replaced from
outside safe (battery not included)
Opens with 4-digit pin # or the swipe of any card with a magnetic strip
i.e. driver’s license, credit card, gift card, etc.
Half Shelves (3)- Lined with rubber to protect valuables
Rear access holes for security cable installation and in-safe charging access
Floor mounting plate included (hardware and screws not included)
Up to 18” Laptops
Cell Phones, iPod, iPad
Keys
Wallet
Jewelry
Money
Important Documents
Prescription Medications
Glasses
Smaller Items
SAFELY STORE AND SECURE:
FEATURES:
72” Vinyl Coated
Steel Cable
Hook
Mounting Plate
Interior:
18.5”h x 6.5”w x 12”d
Interior Shelves:
Height to second shelf 9.5”
Height to third shelf 14”
Shelf width 3.25”
SECURE RELIABLE PEACE OF MIND
Text
Note: Safe can be opened by EITHER keypad combination OR card swipe
once programmed.
Electronic Keypad:
1. Use keypad to punch in 4-digit number code
(Factory set code is: 1 2 3 4)
2. Press #
3. Wait until screen reads: “Good”
(If code is wrong, screen will read “E-code” and beep. Retry.)
4. Rotate turning knob counter-clockwise and pull open
Please Note:
- There will be a 5 minute penalty after 4 consecutive wrong
code attempts
- Press * to delete the latest entered digit
- After 20 seconds of no activity, lock will go into sleeping
mode. Press any digit to activate.
Card Reader:
1. Press #
2. Wait until screen reads: “Card”
3. Swipe card (with magnetic strip facing keypad)
4. Wait until screen reads: “Opened”
5. Rotate turning knob counter-clockwise and pull
Close door and rotate turning knob clockwise to relock bolts
If bolts are deployed, reopen safe before closing
Changing Keypad Combination:
1. Press * * 0 #
2. Screen should read: “Code”
3. Input current combination
(Factory set code is: 1 2 3 4)
4. Press #
5. Screen should read: “Good”
6. Input custom 4-digit combination
7. Press #
8. Screen should read: “Again”
9. Re-enter custom 4-digit combination
10. Press #
11. Screen should read: “Good”
Programming Card Reader:
1. Press * * 6 #
2. Screen should read: “Code”
3. Input 4-digit combination
4. Press #
5. Screen should read: “Card”
6. Swipe desired card
(with magnetic strip facing keypad)
7. Swipe until screen reads: “Good”
instead of “Again”
Deleting Card Information From Reader:
1. Press * * 8 #
2. Screen should read: “Code”
3. Input 4-digit combination
4. Press #
5. Screen should read: “Clear”
Note: If input code is wrong, screen will read “E-code” and beep. Retry.
Note: After card reader is programmed,
order to reprogram with another card.
USER'S INSTRUCTION MANUAL:
OPENING SAFE:
CLOSING SAFE:
CUSTOM PROGRAMMING SAFE:
DORM SAFE US Patent D617974
Note: Low battery alert will show on keypad screen (9V battery not included)
1. Slide battery cover downward and remove to expose battery compartment
2. Disconnect battery from battery connector
3. Replace and reconnect new battery to battery connector
INSERTING AND CHANGING KEYPAD BATTERY:
Keep liquids away from keypad
Do NOT disassemble safe -- For all repairs call Stealth Customer Service
1. Insert one end of steel cable through safe rear
access hole
2. Wrap cable around a sturdy and secure object
next to safe
3. Insert other end of steel cable into safe through
the other rear access hole
4. Clasp each end of cable to hook
5. Clasp hook onto attachment hole connected to
bottom shelf to secure cable to safe
1.
two (2) screws are revealed
2. Unscrew and remove both screws
3.
metal mounting plate
4. Secure mounting plate by screwing it down to
desired location using the six (6) holes in the middle
and front of the plate (screws not included)
- Use proper drill tools depending on
the safe on (wood, tile, or concrete)
- Mark the exact locations of the mounting
to go
- Drill the appropriate size holes for the
anchors you are using
- Match the mounting plate holes over the
-
screwing the appropriate screws through
5. Slide Dorm Safe back onto the mounting plate
6. Rescrew safe back to mounting plate
7.
8. Your Dorm Safe is now securely mounted
SECURING SAFE WITH CABLE:
MOUNTING SAFE:
CARE AND MAINTENANCE:
Security Cable
Attachment Hole
Other Stealth Safe manuals
