STEINEL NightmatIQ User manual

NightmatIQ Plus
RU
CN
BG
LV
LT
EE
HR
SI
RO
PL
SK
CZ
HU
TR
GR
NO
FI
DK
SE
PT
ES
IT
NL
FR
GB
DE
I
STL-11104-20_BDAL_NightmatIQ_148x210mm 2.indd 1
NightmatIQ
NightmatIQ Plus
RU
CN
BG
LV
LT
EE
HR
SI
RO
PL
SK
CZ
HU
TR
GR
NO
FI
DK
SE
PT
ES
IT
NL
FR
GB
DE
I
STL-11104-20_BDAL_NightmatIQ_148x210mm 2.indd 1
NightmatIQ
DE
GB
FR
NL
IT
ES
PT
SE
DK
FI
NO
GR
TR

Index
1. About this document 3
2. General safety precautions 3
3. System description 4
4. Electrical connection 9
5. Installation 10
6. Function 19
7. Cleaning and maintenance 24
8. Disposal 24
9. Manufacturer's warranty 25
10. Technical specifications 26
11. Troubleshooting 27

– 3 – Index
1. About this document
– Under copyright. Reproduction either in whole or in part
only with our consent.
– Subject to change in the interest of technical progress.
!
Hazard warning!
Warning of hazards from electricity!
Warning of hazards from water!
2. General safety precautions
!Failure to observe these operating instructions
presents hazards!
These instructions contain important information on the
safe use of this product. Particular attention is drawn to
potential hazards. Failure to observe this information may
lead to death or serious injuries.
• Read instructions carefully.
• Follow safety advice.
• Keep instructions within easy reach.
– Working with electrical current may produce hazardous
situations. Touching live parts can result in electrical
shock, burns or death.
– Work on mains voltage must only be performed by
qualified, skilled personnel.
– National wiring regulations and electrical operating
conditions must be observed (e.g. DE: VDE0100,
AT:ÖVE-ÖNORM E8001-1, CH:SEV1000).
– Only use genuine replacement parts.
– Repairs must only be carried out by companies qualified
to do so.

– 4 – Index
3. System description
Proper use - NighmatIQ
– Photo-cell controller, suitable for wall mounting indoors
and outdoors.
– Twilight setting function can be selected by potentio-
meter
– Can be used as a standalone sensor.
Proper use - NighmatIQ Plus
– Photo-cell controller, suitable for wall mounting indoors
and outdoors.
– Functions can be set via the Steinel Connect app.
– Can be used as a standalone sensor or interconnected
with Bluetooth.
Operating principle
– The photo-cell controller detects ambient light level by
means of the
light sensor and compares this with the light-level
threshold selected.
– If ambient brightness is below the light-level threshold,
the connected load is switched ON.
– If ambient brightness is above the light-level threshold,
the connected load is switched OFF.

– 5 – Index
Package contents - NightmatIQ / NightmatIQ Plus
3.1
I
A
I
B
2× 2× 1×
1×
1× 1×
– 1 NightmatIQ / NightmatIQ Plus
– 2 screws
– 2 wall plugs
– 1 sealing plug
– 1 safety data sheet
– 1 quick-start guide

– 6 – Index
Product dimensions - NightmatIQ / NightmatIQ Plus
3.2
38mm
95mm
95mm
IP54

– 7 – Index
NightmatIQ product components
3.3
A
E
C
D
B
F
A Cover
B Twilight setting potentiometer
C Photo-cell controller housing
D Light-level sensor
E Connecting terminal
F Optional inlet for surface wiring
3.4
30
min
10
min
OFF
G
G Detail: twilight setting potentiometer

– 8 – Index
NightmatIQ Plus product components
3.5
A
E
C
D
F
B
A Cover
B Status LED
C Photo-cell controller housing
D Light-level sensor
E Connecting terminal
F Optional inlet for surface wiring

– 9 – Index
4. Electrical connection
Circuit diagram
4.1
L
LL
N
PE
N N N
L
I
O
The mains power supply lead is a 3-core cable:
L= Phase conductor (usually black, brown or grey)
N= Neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
The floodlight can also be connected to the power supply
downstream of a mains switch if it is ensured that the
mains switch is left ON all the time.
The sealing plugs provided are intended for a mains supply
lead with an outer diameter of 5-10mm.

– 10 – Index
5. Installation
Hazard from electrical power.
Touching live parts can result in
electrical shock, burns or death.
• Switch OFF power and interrupt power supply.
• Using a voltage tester, check to make sure that the
power supply is disconnected.
• Make sure power supply remains interrupted.
Risk of damage to property!
Mixing up connection leads may produce
a short circuit.
• Identify connection leads.
• Connect the leads correctly.
Preparing for installation
• Check all components for damage. Do not use the
floodlight if it is damaged.
• Select an appropriate site to install the product.
–Vibration-free.
–Not in explosive atmospheres.
–Not on normally flammable surfaces.
–The unit must not be influenced by light
from the connected load.

– 11 – Index
Mounting procedure
5.1
I
O
• Switch OFF power supply.
• Check to make sure the power supply is switched OFF.
• Unscrew and detach cover.
5.2
2
• Mark drill holes.

– 12 – Index
5.3
3
6mm Ø
• Drill holes (ø 6 mm) and fit wall plugs.

– 13 – Index
Concealed version
5.4
max.1Nm
• Route cable through the unit.
• Fit unit, tightening screws with a torque of no more
than 1 Nm.

– 14 – Index
Surface-mounted installation
5.5
• Using a screwdriver, carefully prise out the optional inlet
for surface wiring.
5.6
• Fit sealing plug.

– 15 – Index
5.7
max.1Nm
• Route cable through the unit.
• Fit unit, tightening screws with a torque of no more
than 1 Nm.

– 16 – Index
5.8
• Connect mains power supply lead as shown in the
wiring diagram.
➔„4. Electrical connection“

– 17 – Index
5.9
1.
2.
• Fit cover.
5.10
7
• Screw on cover.

– 18 – Index
5.11
I
O
• Switch ON power supply.
• Setting functions.
➔„6. Function“

– 19 – Index
6. Function
NightmatIQ
On the NightmatIQ, the twilight setting is selected by hand
at the twilight setting potentiometer.
Hazard from electrical power.
Touching live parts can result in electrical shock,
burns or death.
• Switch OFF power and interrupt power supply.
• Using a voltage tester, check to make sure that the
power supply is disconnected.
• Make sure power supply remains interrupted.
• Factory settings
– Twilight level: 75lux
Twilight setting (G)
The response threshold (twilight) can be infinitely varied
from approx. 1 to 75lux.
– = Twilight operating mode (approx. 75lux)
– = twilight operating mode/night-time operating mode
(approx. 1lux)

– 20 – Index
Manual twilight setting for NightmatIQ
6.1
1.
2.
3.
I
O
• Switch OFF power supply.
• Check to make sure the power supply is switched OFF.
• Unscrew cover.
6.2
30
min
10
min
OFF
B
• Using the screwdriver, set the response twilight
threshold to any chosen level.