Stelpro RE153 Series User manual

INSALUX4RE153RE1560217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RE153 - RE156 SERIES
JUNCTION BOX INSTALLATION AND WIRING - LEFT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Position the relay on top of the voltage separator. Position the relay
in the junction box (Arrow pointing up) and install with screws. FIG. 1
3. Pass the blue wires of the relay through the hole of the separator
FIG. 2
4. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Then, insert the
same wires into the voltage separator hole. Connect the low voltage
wires with the relay wires using an appropriate wire nut. For the
connections, refer to the diagram included with the relay.
5. Connect one of the black wires of the relay with the wires of the
heating element, using a wire nut. FIG. 3
6. Connect the other black wire of the relay with the line feed (L1) and
the wire coming out of the wireway with the other line (L2/N). FIG. 4
7. Close the junction box and replace the cover, making sure the wires
are well positioned.
FIG. 1 FIG. 2
FIG. 4FIG. 3
E
GND
ALIMENTATION
L2/N
A
L1
POWER SUPPLY
24V
NOIR/BLACK
TH
R
NOIR/BLACK
E
OU/OR ROUGE/RED
1041 Parent Saint-Bruno
J3V 6L7 (450)-441-0101 DATE:
APP. PAR:
TITRE:
Dessinateur: LK
DL
03-09-15
MISE À LA TERRE
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
GND
A
GROUND
G14
ELEMENT
THERMOSTAT (2P)
ÉLÉMENTE
TH
RÉVISION:
RELAY
RELAISR
P-117

INSALUX4RE153RE1560217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RE153 - RE156 SERIES
JUNCTION BOX INSTALLATION AND WIRING - RIGHT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Position the relay on top of the voltage separator. Position the relay
in the junction box (Arrow pointing up) and install with screws. FIG. 1
3. Pass the blue wires of the relay through the hole of the separator
FIG. 2
4. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Then, insert the
same wires into the voltage separator hole. Connect the low voltage
wires with the relay wires using an appropriate wire nut. For the
connections, refer to the diagram included with the relay.
5. Connect one of the black wires of the relay to the wire coming out of
the wireway. FIG. 3
6. Connect the other black wire of the relay with the line feed (L1) and
the wire from the thermal protection with the line feed (L2/N). FIG. 4
7. Close the junction box and replace the cover, making sure the wires
are well positioned.
FIG. 1 FIG. 2
FIG. 4FIG. 3
E
GND
ALIMENTATION
L2/N
A
L1
POWER SUPPLY
24V
NOIR/BLACK
TH
R
NOIR/BLACK
BLEU/BLUEBLEU/BLUE
E
1041 Parent Saint-Bruno
J3V 6L7 (450)-441-0101 DATE:
APP. PAR:
TITRE:
Dessinateur: LK
DL
03-09-15
MISE À LA TERRE
THERMAL PROTECTION
BUILT-IN OR WALL MOUNTED
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
INTÉGRÉ OU MURAL
GND
A
GROUND
G14
ELEMENT
THERMOSTAT (2P)
ÉLÉMENTE
TH
RÉVISION:
RELAY
RELAISR
P-118

INSALUX4RE153T0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RE153T SERIES
JUNCTION BOX INSTALLATION AND WIRING - LEFT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Position the relay on top of the voltage separator. Position the relay
In the junction box (Arrow pointing up) and install with screws. FIG. 1
3. Insert the black, red and white relay wires (control side) into the hole
of the voltage separator. FIG. 2
4. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Then, insert the
same wires into the voltage separator hole. Connect the low voltage
wires with the relay wires using a wire nut. Refer to the diagram
included with the relay for the different options.
5. Connect the blue wire of the relay to the wires of the heating
element. FIG. 3
6. Connect the white wire of the relay (power side) to the wire coming
out of the wireway and the line feed (L2/N) wire by using an
appropriate wire nut and connect the black relay wire (power side) to
the other wire coming from the line feed (L1) by using an appropriate
wire nut. FIG. 4
7. Close the junction box and replace the cover, making sure the wires
are well positioned.
FIG. 1 FIG. 2
FIG. 4FIG. 3
GND
POWER SUPPLY
E
A
L2/N
ALIMENTATION
L1
A1
A2
G
Bleu /
Blue
Noir /
Black
Blanc /
White
Blanc
/
White
TH 24V
Noir /
Black Rouge
/ Red
R
RELAIS
R
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
A
G14
ELEMENT
ÉLÉMENT
THERMOSTATTH
E
RELAY
MISE À LA TERRE
GROUND
GND
APP. PAR:
DATE:
J3V 6L7 (450)-441-0101
1041 Parent Saint-Bruno
TITRE:
DL
RÉVISION: LK
Dessinateur:
P-119
03-09-15

INSALUX4RE153T0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RE153T SERIES
JUNCTION BOX INSTALLATION AND WIRING - RIGHT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Position the relay on top of the voltage separator. Position the relay
in the junction box (Arrow pointing up) and install with screws. FIG. 1
3. Insert the black, red and white relay wires (control side) into the hole
of the voltage separator. FIG. 2
4. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Then, insert the
same wires into the voltage separator hole.
5. Connect the low voltage wires with the relay wires using a wire nut.
Refer to the diagram included with the relay for the different options.
6. Connect the blue relay wire with the wire that comes out of the wire
way by using an appropriate wire nut. FIG. 3
7. Connect the white relay wire (power side) to the thermal protection
wire and a line feed (L2/N) wire by using an appropriate wire nut and
connect the black relay wire (power side) to the other wire coming
from the line feed (L1) by using an appropriate wire nut. FIG. 4
8. Close the junction box and replace the cover, making sure the wires
are well positioned.
FIG. 1 FIG. 2
FIG. 4FIG. 3
L1
ALIMENTATION
GND
POWER SUPPLY
A
L2/N
Blanc /
White
Bleu /
Blue
Noir /
Black
A1
A2
G
Blanc
/
White
TH 24V
Noir /
Black
Rouge
/ Red
R
E
RELAISR
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
A
G14
ELEMENT
ÉLÉMENT
THERMOSTAT
TH
E
RELAY
MISE À LA TERRE
GROUND
GND
APP. PAR:
DATE:
J3V 6L7 (450)-441-0101
1041 Parent Saint-Bruno
TITRE:
03-09-15
DL
RÉVISION: LKDessinateur:
P-120

INSALUX4R240T-340T0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RM240T – 347T SERIES WITH TRANSFORMER
JUNCTION BOX INSTALLATION AND WIRING - LEFT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Bend the pin on top of the relay. Insert the voltage separator on the
relay and screw with the ring nut supplied. FIG. 1
3. Position the relay in the top of the junction box and install with
screws. FIG. 2
4. Connect the red wire of the relay (power side) to the wire coming
out the wireway. FIG. 3
5. Connect the blue/orange wire of the relay to the heating element
wires and the line feed wire (L1) and connect the black relay wire
(power side) to the other wire coming from the line feed (L2/N) by
using an appropriate wire nut. FIG. 4
6. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Connect the
low voltage wires with the relay wires, using a wire nut. Please
refer to schematic for connection options.
7. Close the junction box and replace the cover, making sure the
wires are well placed inside the box.
FIG. 1 FIG. 2
FIG. 4FIG. 3
L1
ALIMENTATION
GND
POWER SUPPLY
E
A
BLU (240V/600V)
ORG (208V)
ROUGE/RED
24V
L2/N
NOIR/BLACK
TH R
RELAISR
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
A
G14
ELEMENT
ÉLÉMENT
THERMOSTATTH
E
RELAY
MISE À LA TERRE
GROUND
GND
APP. PAR:
DATE:
J3V 6L7 (450)-441-0101
1041 Parent Saint-Bruno
TITRE:
17-02-17
DL
RÉVISION: LKDessinateur:
P-121

INSALUX4R240T-340T0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RM240T – 347T SERIES WITH TRANSFORMER
JUNCTION BOX INSTALLATION AND WIRING - RIGHT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Bend the pin on top of the relay. Insert the voltage separator on the
relay and screw with the ring nut supplied. FIG. 1
3. Position the relay in the top of the junction box and install with
screws. FIG. 2
4. Connect the red wire of the relay (Power side) to the red wire
coming out the Wireway by using an appropriate wire nut. FIG. 3
5. Connect the blue/orange wire of the relay to the wire of the thermal
protection and the wire of the line feed (L1). Connect the black
relay wire (power side) to the other wire coming from the line feed
(L2/N) by using an appropriate wire nut. FIG. 4
6. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Connect the
low voltage wires with the relay wires, using a wire nut. Please
refer to schematic for connection options.
7. Close the junction box and replace the cover, making sure the
wires are well placed inside the box.
FIG. 1 FIG. 2
FIG. 4FIG. 3
L1
ALIMENTATION
GND
POWER SUPPLY
E
A
BLU (240V)/ORG (208V)
ROUGE/RED
R24V
L2/N
NOIR/BLACK
TH
RELAISR
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
A
G14
ELEMENT
ÉLÉMENT
THERMOSTATTH
E
RELAY
MISE À LA TERRE
GROUND
GND
APP. PAR:
DATE:
J3V 6L7 (450)-441-0101
1041 Parent Saint-Bruno
TITRE:
17-02-17
DL
RÉVISION: LKDessinateur:
29-09-09
P-122

INSALUX4R347C0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RM347C SERIES WITHOUT TRANSFORMER
JUNCTION BOX INSTALLATION AND WIRING - LEFT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Bend the pin on top of the relay. Insert the voltage separator on the
relay and screw with the ring nut supplied. FIG. 1
3. Position the relay in the top of the junction box and install using
screws. FIG. 2
4. Connect the red wire of the relay (power side) to the wires of the
heating element. FIG. 3
5. Connect the black wire of the relay (power side) to the other wire
coming from the line feed (L1) by using an appropriate wire nut
and connect the red wire coming out the wireway to the other wire
coming from the line feed (L2/N) by using an appropriate wire nut.
FIG. 4
6. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Connect the
low voltage wires with the relay wires, using a wire nut. Please
refer to schematic for connection options.
7. Close the junction box and replace the cover, making sure the
wires are well placed inside the box.
FIG. 1 FIG. 2
FIG. 4FIG. 3
E
GND
ALIMENTATION
L2/N
A
L1
POWER SUPPLY
24V
NOIR/BLACK
TH
R
NOIR/BLACK
E
OU/OR ROUGE/RED
1041 Parent Saint-Bruno
J3V 6L7 (450)-441-0101 DATE:
APP. PAR:
TITRE:
Dessinateur: LK
DL
03-09-15
MISE À LA TERRE
THERMAL PROTECTION
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
GND
A
GROUND
G14
ELEMENT
THERMOSTAT (2P)
ÉLÉMENTE
TH
RÉVISION:
RELAY
RELAISR
P-117

INSALUX4R347C0217
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
ARCHITECTURAL BASEBOARD | ALUX4 SERIES
RELAY INSTALLATION
RM347C SERIES WITHOUT TRANSFORMER
JUNCTION BOX INSTALLATION AND WIRING - RIGHT SIDE ONLY
1. Remove the cover of the unit and remove the junction box cover.
2. Bend the pin on top of the relay. Insert the voltage separator on the
relay and screw with the ring nut supplied. FIG. 1
3. Position the relay in the top of the junction box and install using
screws. FIG. 2
4. Connect the red wire of the relay (power side) to the wire coming
out of the wireway. FIG. 3
5. Connect the black relay wire (power side) to the other wire coming
from the line feed (L1) by using an appropriate wire nut and the
wire from the thermal protection to the line feed wire (L2/N). FIG. 4
6. Insert the control wires supplied by the installer into the baseboard
electrical box through one of the knockouts (KOE). Connect the
low voltage wires with the relay wires, using a wire nut. Please
refer to schematic for connection options.
7. Close the junction box and replace the cover, making sure the
wires are well placed inside the box.
FIG. 1 FIG. 2
FIG. 4FIG. 3
E
GND
ALIMENTATION
L2/N
A
L1
POWER SUPPLY
24V
NOIR/BLACK
TH
R
NOIR/BLACK
BLEU/BLUEBLEU/BLUE
E
1041 Parent Saint-Bruno
J3V 6L7 (450)-441-0101 DATE:
APP. PAR:
TITRE:
Dessinateur: LK
DL
03-09-15
MISE À LA TERRE
THERMAL PROTECTION
BUILT-IN OR WALL MOUNTED
OUTSIDE CONNECTION
PROTECTION THERMIQUE
CONNEXION EXTÉRIEURE
INTÉGRÉ OU MURAL
GND
A
GROUND
G14
ELEMENT
THERMOSTAT (2P)
ÉLÉMENTE
TH
RÉVISION:
RELAY
RELAISR
P-118