Stenner Pumps S Series Manual

TO BE I STALLED A D MAI TAI ED BY PROPERLY TRAI ED PROFESSIO AL I STALLER
O LY. READ MA UAL & LABELS FOR ALL SAFETY I FORMATIO & I STRUCTIO S.
WARNING
S SERIES W 4.01.02
PERISTALTIC METERING PUMPS
I STALLATIO A D MAI TE A CE MA UAL
PERISTALTIC METERING PUMPS SINCE 1957
Control Modes HALL EFFECT and MANUAL

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
2
Warranty and Ser ice Policy........................................ 3
SaFety inStrUctionS .................... COVER, 4-6, 8, 18, 34, 41-43,
45, 46, 48, 51, 52, 54-58, 61, 62, 67, 69
FloW rate oUtPUtS ........................................................... 6
MaterialS oF conStrUction ........................................... 7
cHeMical reSiStance GUide ......................................... 8-9
acceSSorieS ..................................................................... 10
General inForMation ................................................ 11-13
ModBUS reQUireMentS ................................................... 13
conFiGUration .............................................................. 14-30
control ModeS Manual & Hall Effect ............................... 31-35
oPeratinG diSPlay ........................................................ 36-40
connectionS................................................................... 47-50
inStallation .................................................................. 51-57
troUBleSHootinG.......................................................... 58-61
tUBe rePlaceMent ........................................................ 62-68
cleaninG tHe Point oF injection .................................. 69-70
PartS .............................................................................. 71-75
Wall MoUntinG BracKet diMenSionS ................................. 76
IMS 011623
FW 4.01.02
TABLE O CONTENTS
SERIES S SERIES multiple operational modes and indicators
MODEL pump head-plastic latches pump head-stainless steel latches pump head-thumbscrews
S30 S40 S50

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
3
WARRANTY AND CUSTOMER SERVICE
LIMITED WARRANTY
Stenner Pump Company will for a period of 2 years from the date of purchase (proof of purchase required) repair or
replace at our option all defective parts. Stenner is not responsible for any removal or installation costs. Pump tube
assemblies and rubber components are considered perishable and are not covered in this warranty. Pump tube will be
replaced each time a pump is in for service, unless otherwise specified. The cost of the pump tube replacement will be
the responsibility of the customer. Stenner will incur shipping costs for warranty products shipped from our factory in
Jacksonville, Florida. Any tampering with major components, chemical damage, faulty wiring, weather conditions, water
damage, power surges, or products not used with reasonable care and maintained in accordance with the instructions
will void the warranty. Stenner limits its liability solely to the cost of the original product. We make no other warranty
expressed or implied.
RETURNS
Stenner offers a 30-day return policy on factory direct purchases. Except as otherwise provided, no merchandise will be
accepted for return after 30 days from purchase. To return merchandise at any time, call Stenner at 800.683.2378 for a
Return Merchandise Authorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of your invoice or
packing slip with your return.
DAMAGED OR LOST SHIPMENTS
Check your order immediately upon arrival. All damage must be noted on the delivery receipt. Call Stenner Customer
Service at 800.683.2378 for all shortages and damages within seven (7) days of receipt.
SERVICE & REPAIRS
efore returning a pump for warranty or repair, remove chemical from pump tube by running water through the tube, and
then run the pump dry. Following expiration of the warranty period, Stenner Pump Company will clean and overhaul any
Stenner metering pump for a minimum labor charge plus necessary replacement parts and shipping. All metering pumps
received for overhaul will be restored to their original condition. The customer will be charged for missing parts unless
specific instructions are given. To return merchandise for repair, call Stenner at 800.683.2378 or 904.641.1666 for a
Return Merchandise Authorization (RMA) number.
DISCLAIMERS
The information in this manual is not intended for specific purposes.
The Stenner Pump Company reserves the right to make changes to prices, products, and specifications at any time
without prior notice.
The Modbus communication protocol is a product of the Modbus Organization, www.modbus.org.
TRADEMARKS
QuickPro®is a registered trademark of the Stenner Pump Company.
Santoprene®is a registered trademark of Exxon Mobil Corporation.
Versilon®is a registered trademark of Saint-Gobain Performance Plastics.
Pellethane®is a registered trademark of Lubrizol Advanced Materials, Inc.
Hastelloy®is a registered trademark of Haynes International, Inc.
AquaShield™is a trademark of Houghton International.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
4
SA ETY INSTRUCTIONS
Warns about hazards that CAN cause death, serious personal injury, or property damage
if ignored.
ELECTRIC SHOCK HAZARD
RISK O ELECTRIC SHOCK
Connect only to a branch circuit protected by a ground-fault circuit-interrupter (GFCI). Contact a qualified
electrician if you cannot verify that the receptacle is protected by a GFCI.
RISQUE DE CHOC ELECTRIQUE
rancher seulement à un réseau électrique protégé par un DDFT. Contactez un électricien certifié si vous ne pouvez
pas vérifier que la prise est protégé par un DDFT.
PELIGRO DE DESCARGA ELECTRICA
Conecte a un circuito en derivación protegido por un interruptor de descarga a tierra (GFCI). Contacte a un
electricista certificado si no puede verificar que su receptáculo esté protegido por dicho interruptor (GFCI).
To reduce the risk of electric shock, replace damaged cord immediately. Contact the factory or an
authorized service facility for repair.
DO NOT alter the power cord or plug end. DO NOT use receptacle adapters.
DO NOT use pump with a damaged or altered power cord or plug. Contact the factory or
authorized service facility for repair.
After installation, the power supply plug must be accessible during use.
To reduce the risk of injury, do not permit children to use this product. This appliance is not to be
used by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
This pump has not been investigated for use in marine areas.
La pompe n’a pas été vérifiée et approuvée pour utilisation sur des applications de
installation marine.
Este dosificador no ha sido investigado para uso en áreas marinas.
EXPLOSION HAZARD
This equipment IS NOT explosion proof. DO NOT install in an explosive environment.
RISK O CHEMICAL EXPOSURE AND OVERDOSE
Potential for chemical burns, fire, explosion, personal injury, or property damage. To reduce risk of exposure, the use
of proper personal protective equipment is mandatory. To reduce risk of overdosing, follow proper installation methods
and recommendations. Check your local codes for additional guidelines.
RISK O IRE HAZARD
DO NOT install or operate on any flammable surface.
Pump is not recommended for installation in areas where leakage can cause personal injury or
property damage.
PELIGRO
PELIGRO
IMPORTANT SA ETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including
the following:
READ AND OLLOW ALL INSTRUCTIONS

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
5
SA ETY INSTRUCTIONS continued
Warns about hazards that WILL or CAN cause minor personal injury or property damage
if ignored.
To reduce risk of electric shock, pull plug before servicing this pump.
This pump has been evaluated for use with water only.
Non-submersible pump. Suitable for indoor and outdoor use.
Pompe non submersible. Adaptée à une utilisation aussi bien à l’intérieur qu’à l’extérieur.
Dosificador no sumergible. Adecuado para el uso interior y exterior.
PLUMBING
Chemical feed pump installation must always adhere to your local plumbing codes and requirements. e sure
installation does not constitute a cross connection. Check local plumbing codes for guidelines.
Electrical installation should adhere to all national and local codes. Consult licensed professional
for assistance with proper electrical installation.
Pump uses a class 2 switching power supply.
PINCH PONT HAZARD
Use extreme caution when replacing pump tube. e careful of your fingers and do not place fingers near rollers.
SAVE THESE INSTRUCTIONS
NOTICE: Indicates special instructions or general mandatory action.
This metering pump is portable and designed to be removable from the plumbing system without damage to
the connections.
This metering pump and its components have been tested for use with the following chemicals; Sodium Hypochlorite
(10-15%), Muriatic Acid (20-22 aume, 31.5% Hcl), and Soda Ash.
Cette a pompe de dosage et ses composants ont été testés pour utilisation avec les produits chimiques suivants;
Hypochlorite de Sodium (solution de 10-15%); Acide Muriatique (20-22 aume, 31.5% Hcl); Cendre de Soude.
efore installing or servicing the pump, read the pump manual for all safety information and complete instructions.
The pump is designed for installation and service by properly trained personnel.
No user replaceable parts inside.
Do not install at altitudes over 2000 meters.
CAUTION
CAUTION
CAUTION
CAUTION
CUIDADO
ATTENTION
CAUTION
CAUTION
CAUTION
CAUTION

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
6
LOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide. The output data is an approximation based on pumping water under
a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump Company recommends that all metering
pumps undergo field calibration by means of analytical testing to confirm their outputs.
25 psi (1.7 bar) max.
Model Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S3003 S3003 3 100:1 0.40–40.0 0.017–1.67 2.13–213.0 0.036–3.56 1.51–151.0 0.063–6.31 63.09–6309.0 1.05–105.0
S3004 S3004 4 100:1 0.60–60 0.025–2.50 3.20–320.0 0.053–5.33 2.27–227.0 0.095–9.46 94.64–9464.0 1.58–158.0
S3005 S3005 5 100:1 0.85–85 0.035–3.54 4.53–453 0.076–7.56 3.22–322 0.134–13.41 134.07–13407 2.23–223
S405X S405X 5X 100:1 1.5–150.0 0.06–6.25 8.0–800.0 0.13–13.33 5.7–567.0 0.24–23.66 236.59–23,659.0 3.94–394.0
S505G S505G 5G 100:1 3.2-315.0 0.133-13.13 17.07-1680.0 0.284-28.00 12.11-1192.0 0.505-49.68 504.72-49,684.0 8.41-828.0
Approximate Output @ 50/60Hz
100 psi (6.9 bar) max.
Model Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S3001 S3001 1 100:1 0.05–5.0 0.002–0.21 0.27–27.0 0.004–0.44 0.19–19.0 0.008–0.79 7.89–789.0 0.13–13.0
S3002 S3002 2 100:1 0.17–17.0 0.007–0.71 0.91–91.0 0.015–1.51 0.64–64.0 0.027–2.68 26.81–2681.0 0.45–45.0
S3007 S3007 7 100:1 0.40–40.0 0.017–1.67 2.13–213.0 0.036–3.56 1.51–151.0 0.063–6.31 63.09–6309.0 1.05–105.0
S407X S407X 7X 100:1 0.60–60.0 0.03–2.50 3.2–320.0 0.053–5.34 2.3–227.0 0.09–9.46 94.64–9464.0 1.58–158.0
S507G S507G 7G 100:1 1.3-125.0 0.054-5.21 6.93-667.0 0.116-11.11 4.92-473.0 0.205-19.72 205.04-19,716.0 3.42-329.0
Approximate Output @ 50/60Hz

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
7
MATERIALS O CONSTRUCTION
S30 / S40 / S50
All Housings Polycarbonate
Pump Tube Santoprene®(FDA approved) or Versilon®
Suction/Discharge Tubing, Ferrules 1/4" & 6 mm Polyethylene (FDA approved)
Tube Fittings & Injection Fittings PVC or Polypropylene (both NSF listed)
Connecting uts PVC or Polypropylene (both NSF listed)
Suction Line Strainer and Cap PVC or Polypropylene (both NSF listed); ceramic weight
All Fasteners Stainless steel
S30
Check Valve Duckbill Santoprene®(FDA approved) or Pellethane®
3/8" Adapter PVC or Polypropylene (both NSF listed)
Pump Head Rollers Polyethylene
Leak Detect Components Hastelloy®
Pump Head Latches Polypropylene
S40
Ball Check Valve Components
-Ceramic ball (FDA approved); tantalum spring; FKM seat & O-ring OR
-Ceramic ball (FDA approved); stainless steel spring; EPDM seat; Santoprene®O-ring
Pump Head Rollers Polyethylene
Leak Detect Components Hastelloy®
Pump Head Latches Stainless steel
S50
Ball Check Valve Components
-Ceramic ball (FDA approved); tantalum spring; FKM seat & O-ring OR
-Ceramic ball (FDA approved); stainless steel spring; EPDM seat; Santoprene®O-ring
Pump Head Rollers Polycarbonate
Guide Rollers Polyethylene
Thumbscrews Stainless steel and PVC
Leak Detect Components Hastelloy®and stainless steel
Pump Head Support and Transition Sleeve Santoprene®
Tube Pull PVC

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
8
CHEMICAL RESISTANCE GUIDE
The information is provided ONLY as a guide to assist in determining chemical compatibility
for wetted components. Testing under the specific conditions of the application is recommended. Stenner Pump
Company assumes no responsibility for its accuracy. Outside factors including but not limited to temperature,
pressure, mechanical stress, and solution concentration can affect material compatibility in a particular application.
Stenner makes no warranty, expressed or implied, as to the accuracy of this guide or any materials’ suitability for
fitness or purpose for any application. User assumes all risk and liability for use of this guide.
Ratings Key – Chemical Effect
AFluid has minor or no effects
BFluid has minor to moderate effects
CFluid has severe effects
•No data available
Chemical / Solution
Chloroacetic Acid A C C C • • A
Chloroform C C C C A C • A
Chlorosulfonic Acid C C C C C •
Chromic Acid < 50% C A A C A
Chromium Salts A • A • • • •
Citric Acid C A • A A
Copper Chloride A A A A A • A C
Copper Sulfate A A A A A • A
Cottonseed Oil A A A • • A
d-Limonene C A C • •
Ethyl Acetate A C C C C •
Ethyl Alcohol C C • A •
Ethyl Chloride C C C C A C • A
Ethylene Dichloride C C C C A C •
Ethylene Glycol A A A A A A •
Ethylene Oxide A C C C C •
Eucalyptus Oil C C C • • • •
Fatty Acids C A A A C • A
Ferric Chloride A A A A A A C
Ferric Sulfate A A A A A •
Ferrous Chloride A A A A A C • C
Ferrous Sulfate A A A A A C •
Fluoboric Acid A C A C A • •
Fluosilicic Acid A A A A A C •
Formaldehyde < 40% A A C C • A
Formic Acid A C C C C A A
Glucose A A A A A A • A
Glycerin A A A A A A • A
Hydrochloric Acid 20% A C A A A C A C
Hydrochloric Acid 37% A C A A A C A C
Hydrocyanic Acid A A A A C A A
Hydrofluoric Acid < 48% A C A A C C C
Hydrofluoric Acid 48-75% A C C C A C C C
Hydrofluoric Acid, anhydrous C C C C • C C
Hydrogen Peroxide < 50% A A A A A A
Hydrogen Sulfide A A A C • • A
Iodine A A C A C A C
PP
Santoprene
®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel
Chemical / Solution
Acetic Acid 20% A A A A A
Acetic Acid 30% C C A A A
Acetic Acid, Glacial C C C C C • A A
Acetic Anhydride C C C C C • A
Aliphatic Hydrocarbons • • • •
Aluminum Chloride A A A A A
Aluminum Sulfate A A A A A A A
Alums A A A A A A • A
Ammonium Acetate A A A • • A
Ammonium Carbonate A A A A A C •
Ammonium Chloride A A A C A
Ammonium Hydroxide A A A A A
Ammonium Nitrate A A A A C A A
Ammonium Phosphate A A A A A A • C
Ammonium Sulfate A A A A A A
Amyl Acetate A C C C C C • A
Aniline C C C C C A
Antimony Salts A A A • • • •
Arsenic Salts A A A • • • •
arium Hydroxide A A A A •
arium Salts A • A • A • •
eer A A A A A • A A
enzene C C C C • •
enzoic Acid A C A A A • A
leach 5.25% A A A A A • • •
oric Acid A A A A A A A A
romine A A C A C
utyl Acetate A C C C C C • A
utyric Acid A C C C A
Calcium Chloride A A A A • A
Calcium Hydroxide A C A A A •
Calcium Hypochlorite 5% A A A A • A
Calcium Salts A A A A • • •
Carbon Disulfide C C C C A • •
Carbon Tetrachloride C C C C A C •
Castor Oil A A • A• • A
Chlorine see Sodi m Hypochlorite
PP
Santoprene
®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
9
* Products tested and certified by IAPMO according to ANSI/NSF 61 for contact with Sodium Hypochlorite and Water only and ANSI/NSF 372.
Chemical / Solution
Sea Water A A A A A • A C
Silicone Oil C A A A C • A
Silver Nitrate A A A A A A •
Soap Solutions A A A C A A • A
Sodium A A A A • • • •
Sodium isulfate A A A A A • • C
Sodium isulfite A A A A A A •
Sodium orate A A A A A A •
Sodium Carbonate A A A A A A • A
Sodium Chlorate A A A A A C •
Sodium Chloride A A A A A A A
Sodium Dichromate 20% A • • A • • •
Sodium Hydroxide < 20% A A C A
Sodium Hydroxide 20-46.5% A C A C • C
Sodium Hypochlorite 5% A* A A A A C
Sodium Hypochlorite 6-15% A* A A A A C
Sodium Nitrate A A A A A C A
Sodium Silicate A A A A A A •
Sodium Sulfide A A A A A A • C
Sodium Sulfite A A A A A A • A
Solvents C • • • •
Soybean Oil A A A A • • A
Stannous Chloride 15% A A A A • • A
Stearic Acid A A • A
Sulfur Dioxide liquid A C C C • • A
Sulfur Trioxide C A C A • • C
Sulfuric Acid < 40% A C A C
Sulfuric Acid > 40% C C C C A C A C
Sulfurous Acid A A A C C •
Tannic Acid 10% A A A • A
Tanning Liquors A A A A A • • A
Tartaric Acid A A A A A A • C
Titanium Salts A A A • • • •
Triethanolamine A C C C C • • •
Trisodium Phosphate A A A A A • •
Tung Oil C C A • • •
Turpentine C C A C • A
Urea A A A •
Water & rine A A A A A • •
Zinc Chloride A A A A A A
Zinc Salts A A A A • • • •
NOTE: FKM tested to ANSI/NSF 61 with water only.
PP
Santoprene
®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel
Chemical / Solution
Lactic Acid A A A A A
Lead Acetate A A A C C •
Linseed Oil A A A A A • A
Limonene C A C • •
Lubricating Oils C A C A • • A
Magnesium Chloride A A A A A A C
Magnesium Hydroxide A A A A A • A A
Magnesium Sulfate A A A A A A A
Malic Acid A A A A • A
Manganese Salts A A A A • • •
Mercuric Chloride A A A A A • • C
Methylene Chloride C C C C • A
Mineral Oil A A • • •
Mineral Spirits C A A • • A
Muriatic Acid, 20° aume A C A A A • • •
Nckel Chloride C A A A A
Nickel Sulfate A A A A A A A A
Nitric Acid < 10% A C A A A A
Nitric Acid 10-30% C A C A C A A
Nitric Acid 30-60% C C C A C A A
Nitric Acid 70% C C C A C A A
Nitric Acid, red fuming C C C C C C • •
Nitrous Acid A • • • •
Oleic Acid A C C C • A
Oleum 20-25% C C C C • • •
Oxalic Acid A C A A C A A
Palmitic Acid A A A C • A
Petroleum Distillates C C • • A A
Peracetic Acid 5% A A A • •
Peracetic Acid 15% A A • •
Phenol C C A C •
Phosphoric Acid A C A A A C A C
Phthalic Acid A C A A A • A
Pickling Solutions A C • • • • •
Plating Solutions A C • • A C • •
Polyphosphate A A A A • • • •
Potassium Carbonate A A A A A • •
Potassium Chlorate A A A A A •
Potassium Hydroxide A A A A C C A
Potassium Dichromate A A A A A • •
Potassium Iodide A A A • • A
Potassium Permanganate A A A A A • •
PP
Santoprene
®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
10
ACCESSORIES
S30
3 Connecting Nuts 1/4" & 3 Ferrules 1/4" or 6 mm E rope
or 3 Connecting Nuts & 2 Adapters 3/8"
1 Injection Fitting 25 psi (1.7 bar) max.
or 1 Duckbill Check Valve 100 psi (6.9 bar) max.
1 Weighted Suction Line Strainer 1/4", 3/8" or 6 mm E rope
20' Suction/Discharge Tubing 1/4" or 3/8", white or UV black
or 20' Suction/Discharge Tubing 6 mm white E rope
1 Additional Pump Tube
2 Additional Latches
1 Mounting racket
1 Quick Start Guide
S40 / S50
3 Connecting Nuts & 2 Adapters 3/8"
1 all Check Valve
1 Weighted Suction Line Strainer 3/8"
20' Suction/Discharge Tubing 3/8", White or UV lack
1 Additional Pump Tube
1 Mounting racket
1 Quick Start Guide

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
11
GENERAL IN ORMATION
The S Series is an advanced peristaltic pump design with multiple programming features and
performance indicators. The S Series offers practical and flexible functions for municipal, wastewater
and industrial applications.
PUMP EATURES
• rushless DC Motor with ball bearing support
• Switch mode power supply
• Microcontroller
• lue OLED Display
• Six button keypad on control panel
• Modbus RTU over RS-485 capability
M AI N M E NU
-CONFIGURATION
-C ON T R O L M O DE
-R UN P U MP
Button General unction Operating Mode unction
• Moves up in a menu
UP • Toggles between menu options Increases the speed percent in the Manual mode
• Increases a value
• Moves down in a menu
DOWN • Toggles between options Decreases the speed percent in the Manual mode
• Decreases a value
PRIME N/A Runs pump at 100% speed while button is pressed
ON/O N/A Turns pump control ON or OFF
WARNING: DOES NOT REMOVE POWER
BACK Moves one step back in a menu when permitted Cycles the display to show different units of output
ENTER Sets a value Press and hold for 2 seconds to go to the
Main Menu
SETUP
The very first time the pump is turned on, the display will show the Firmware Version followed by the Main Menu screen.
If the pump was previously programmed, the display will return to the mode it was in when it was turned off or if power
was lost.
Main Menu
-Configuration
-Control Mode
-Run Pump
FW: 4.01.02
S SERIES
The display will indicate
the pump's software version.
OUTPUT
• Up to 315.0 gpd @ 25 psi max.
• Up to 125.0 gpd @ 100 psi max.
CONTROL PANEL
NAVIGATION BUTTONS

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
12
GENERAL IN ORMATION continued
Calibrate ump Flow Rate Output (mandatory)
From the Configuration menu, select GPD/LPD Calibration, and enter your pump’s ACTUAL maximum flow rate
output. Refer to illustration below.
IMPORTANT!
The pump’s ACTUAL maximum flow rate entry:
・
Affects flow rate output displayed on the screen during operation in all modes.
・
Contributes to overall calculation of flow rate output in the PPM modes.
rogram Applicable ump arameters
In Configuration menu, program applicable pump parameters, refer to chart below.
1
Enter max pump flow
__0.0 GPD
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
Configuration
- Units
- Clock
- Calibration
adjust
set
2
Pump Parameters Description Control Mode
Display rightness Optimal setting is < 50% for extended periods. All
Units Default is Gallons; enter Liters, if preferred. All
Clock 24-hr format. Enter current time of day and day of the week. All
Leak Detect Calibrate sensitivity to distinguish between water & your chemical. All
Tube Timer Enter number of hours you want pump to run before display All
shows TU E CHANGE.
Password Program a password to prevent unauthorized changes to pump settings. All
Output Relays Three individual relays available; rated for 24VDC @ 50mA max. All
Program communication for:
• S Series to back-up S Series
• S Series to another device
Signal Calibration If factory settings are not s fficient, calibrate the pump using a 4-20mA, 0-10VDC
process meter or powered transmitter.
Reset Totalizer Option to reset the total tallied amount of water treated. Pulse, Hall Effect, PPM
Modbus Setup Modbus RTU over RS-485 capability; pump firmware 3.02.02 or higher Manual, 4-20mA, 0-10VDC, Pulse
3
4
5
HOW TO GET STARTED SUMMARY
Select Mode of Operation
In Control Modes menu, select your mode of operation.
rogram the Options
In your selected control mode, program the options relevant to your application.
Run the ump

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
13
GENERAL IN ORMATION continued
PUMP STATUS INDICATORS
PER ORMANCE INDICATORS ACTIVATED BY PUMP STATUS
Display Alarm Three Output Relays to
on control panel pump, system or device
Tube Change ✓ ✓
Tube Leak ✓ ✓
Standby ✓ ✓
Drive Fault ✓ ✓
Off ✓ ✓
Run –––––– ✓
Mode Change –––––– ✓
Transfer** –––––– ✓
Repeat Pulse –––––– ✓
High Signal ✓ ✓ 4-20mA*or 0-10VDC*
Low Signal ✓ ✓ 4-20mA*or 0-10VDC*
High Flow ✓ ✓ Hall Effect or PPM Feed: Hall Effect
Low Flow ✓ ✓ Hall Effect
Signal Overrun ✓ ✓ Pulse
* Scalable, invertible
** Transfer operation from a primary pump to a backup pump via a relay.
Pump Status Modes of Operation
Pump Status Indicators
Manual, 4-20mA*, 0-10VDC*,
Pulse, 7 Day Timer, Cycle Timer,
PPM Feed: Flow switch
All Modes of Operation
REMOTE COMMUNICATION CAPABILITY WITH MODBUS RTU over RS-485
Requirements
• S Series Pump with firmware version 3.02.02 or higher
• Applicable modes of operation: Manual, 4-20mA, 010VDC, or Pulse
• Stenner Modbus manual
• Modbus RS-485 communication cable & 1 three terminal, liquid tight junction;
purchased separately, part number MOD100

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
14
Returns to Configuration menu
Display BrightnessConfiguration
- Display rightness
- Units
- Clock
100%
adjust set
CON IGURATION MENU
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.
The configuration of the pump parameters should be completed during the initial setup.
DISPLAY BRIGHTNESS
Operator can adjust the brightness level of the pump display from 0% to 100%. There is some visibility
at the minimum setting.
NOTE: For best performance and longevity, the display brightness should not be set higher than 50% for extended periods.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
15
Units
Configuration
-Display rightness
-Units
-Clock
Gallons
Units
Liters
Returns to Configuration menu.
Returns to Configuration menu.
adjust set
adjust set
CON IGURATION MENU continued
UNITS
Operator must set the unit of measure to Gallons or Liters. The selection appears in the pump display
during Control Mode programming.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
16
Today isConfiguration
-Display rightness
-Units
-Clock
Sunday
The time is
00:00:00
adjust
sun- sat set set
CON IGURATION MENU continued
CLOCK
Operator can set the current day of the week and the time of day. The clock is in 24-hour format.
Returns to Configuration menu
When ENTER is pressed for the last digit
in the time of day, the display returns to
Configuration menu
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
17
To Configuration menu
Calibration
-GPD/LPD Calibration
-Signal Calibration
-GO TO CONFIG MENU
CON IGURATION MENU continued
Enter max pump flow
__0.0 GPD
adjust set
Calibration
-GPD/LPD Calibration
-Signal Calibration
-GO TO CONFIG MENU
Calibration
-GPD/LPD Calibration
-Signal Calibration
-GO TO CONFIG MENU
CALIBRATION page 1 of 2
Operator must set the pump’s maximum flow rate output. The units displayed in the Calibration
submenu are controlled by the units selected in the Units submenu.
IMPORTANT: The value entered (in Calibration) for the pump’s maximum output is used to calculate the pump’s
required output for the operating mode in Run Pump. The value is also used to calculate the pump's required run
speed in the PPM eed submenu in Control Mode. For the most accurate dosing possible, determine the actual pump
output. Conduct a drawdown from a graduated calibration column against the discharge run and pressure, equivalent to
the intended installation.
G D or L D is selected in
Units under Configuration
When ENTER is
pressed for the
final digit in
Calibration,
the display
returns to the
Calibration menu
Configuration
-Units
-Clock
-Calibration
To
Calibration menu
Continued on next page
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
18
To Signal Calibration menu
To Signal Calibration menu
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
Signal Calibration
- 4-20mA IN
- 0 - 10V IN
- 4-20mA OUT
To top of
Calibration menu
Signal Calibration
- 0 - 10V IN
- 4-20mA OUT
- GO TO CAL MENU
Connect pump to 0-10V loop
using a process meter or powered transmitter
CON IGURATION MENU continued
CALIBRATION page 2 of 2
Operator can calibrate analog signal inputs and outputs.
4-20mA and 0-10VDC input signals are pre-calibrated at the factory. Only change the input
calibration if the factory settings are not sufficient.
0 - 10V IN Set
Input 0V
0 - 10V IN Set
Input 10V
set back
set
Signal Calibration
- 4-20mA IN
- 0 - 10V IN
- 4-20mA OUT
When pump indicates to input
10V, bring loop to 10.0V (or
desired level). ress ENTER.
When pump indicates to input
0V, bring loop to 0.0V (or
desired level). ress ENTER.
Signal Calibration
- 4-20mA IN
- 0 - 10V IN
- 4-20mA OUT
Continued from previous page
Connect process meter to 4-20mA output signal
4mA OUT Set
0508
adjust
set
20mA OUT Set
2584
set back
In 20mA Out Set, press the
UP or DO N button to adjust
the signal until the meter
reads 20.0. ress ENTER.
In 4mA Out Set, press the UP
or DO N button to adjust the
signal until the meter reads
4.0. ress ENTER.
Input 4mA
4-20mA IN Set
Input 20mA
set back
set
Connect pump to 4-20mA loop
using a process meter or powered transmitter
4-20mA IN Set
When pump indicates to input
20mA, bring loop to 20.0mA
(or desired level). ress ENTER.
When pump indicates to input
4mA, bring loop to 4.0mA
(or desired level). ress ENTER.
To Signal Calibration menu
adjust
CAUTION

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
19
The pump will indicate if the password was
accepted or not and the screen
will return to Configuration menu.
CON IGURATION MENU continued
PASSWORD
Operator can set a password to prevent unauthorized changes to the pump settings.
• The password function is disabled by default.
• Password characters can be 0-9 or A-Z or a combination of both.
• After a password is set it takes two minutes to save, then it will be required to enter the Main Menu.
• To disable a set password, update the password to four blank spaces and confirm.
Displays message for 3 seconds and
returns to Configuration menu.
Configuration
-Clock
-Calibration
-Password
Enter Password
0-9, A-Z set
Confirm Password
0-9, A-Z set
PASSWORD
ACCEPTED
If password was
accepted.
If no password was entered.
Displays message
for 3 seconds
and returns to
Configuration
menu.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.
To Configuration menu
PASSWORD DID NOT
MATCH. PLEASE
RE-ENTER PASSWORD
ok
PASSWORD
DISABLED
If password
was not accepted.

S Series FW 4.01.02 US and Canada 800.683.2378, International 904.641.1666 www.stenner.com
20
Tube Timer
-Current Run Time
-Set Life Timer
-Reset Tube Timer
Tube Timer
-Current Run Time
-Set Life Timer
-Reset Tube Timer
CON IGURATION MENU continued
TUBE TIMER
Operator can set the tube run time in hours, to initiate the tube change indicator. When the set time is
reached, the operating display shows Tube Change.
• After the tube is replaced, reset the current run time to zero.
To Configuration menu
set back
Tube Timer
-Current Run Tim
-Set Life Timer
-Reset Tube Timer
Reset Tube Timer?
Yes
yes/no select
Tube Timer
-Set Life Timer
-Reset Tube Timer
- TO CONFIGURE MENU
Reset Tube Timer?
No
yes/no select
The timer is NOT reset.
To Tube Timer menu
Time to tube change
0000 Hours
adjust set
Time to tube change
_ _ _ 0 Hours
adjust
Configuration
-Calibration
-Password
- Tube Timer
The timer is reset to zero.
Returns to Configuration menu
To Tube Timer menu
Setting the timer to zero
disables this feature
set
RUN TIME IS
X HOURS
To Tube Timer Menu
Displays current tube run time
and returns to Tube Timer Menu
when ENTER is pressed.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.