Stenner Pumps S Series Manual

TO BE I STALLED A D MAI TAI ED BY PROPERLY TRAI ED PROFESSIO AL I STALLER
O LY. READ MA UAL & LABELS FOR ALL SAFETY I FORMATIO & I STRUCTIO S.
WARNING
S SERIES W 3.02.02
PERISTALTIC METERING PUMPS
I STALLATIO A D MAI TE A CE MA UAL
PERISTALTIC METERING PUMPS SINCE 1957

S Series FW 3.02.02 www.stenner.com
2
TABLE O CONTENTS
WARRANTY AND SERVICE POLICY .......................................... 3
SA ETY INSTRUCTIONS................COVER, 4-6, 8, 19, 34, 37, 40,
.44, 52, 56-66, 68-70, 72, 75-76, 78, 81-82, 84-88, 91-92, 97
LOW RATE OUTPUTS............................................................ 6
MATERIALS O CONSTRUCTION ............................................. 7
CHEMICAL RESISTANCE GUIDE .......................................... 8-9
ACCESSORIES .................................................................... 10
GENERAL IN ORMATION ................................................ 11-13
MODBUS REQUIREMENTS ................................................... 13
CON IGURATION ........................................................... 14-31
CONTROL MODES ...........................................................32-55
OPERATING DISPLAY ......................................................56-67
CONNECTIONS ...............................................................68-80
INSTALLATION ............................................................... 81-87
TROUBLESHOOTING....................................................... 88-91
TUBE REPLACEMENT ..................................................... 92-96
CLEANING THE POINT O INJECTION ............................... 97-98
PARTS ........................................................................ 99-103
WALL MOUNTING BRACKET DIMENSIONS........................... 104
IMS 082420
FW 3.02.02
PUMP SERIES RE ERENCE
S SERIES multiple operational modes and indicators
pump head-plastic latches pump head-stainless steel latches
S30 S40

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 3
WARRANTY AND CUSTOMER SERVICE
LIMITED WARRANTY
Stenner Pump Company will for a period of 2 years from the date of purchase (proof of purchase required) repair or
replace at our option all defective parts. Stenner is not responsible for any removal or installation costs. Pump tube
assemblies and rubber components are considered perishable and are not covered in this warranty. Pump tube will be
replaced each time a pump is in for service, unless otherwise specified. The cost of the pump tube replacement will be
the responsibility of the customer. Stenner will incur shipping costs for warranty products shipped from our factory in
Jacksonville, Florida. Any tampering with major components, chemical damage, faulty wiring, weather conditions, water
damage, power surges, or products not used with reasonable care and maintained in accordance with the instructions
will void the warranty. Stenner limits its liability solely to the cost of the original product. We make no other warranty
expressed or implied.
RETURNS
Stenner offers a 30-day return policy on factory direct purchases. Except as otherwise provided, no merchandise will be
accepted for return after 30 days from purchase. To return merchandise at any time, call Stenner at 800.683.2378 for a
Return Merchandise Authorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of your invoice or
packing slip with your return.
DAMAGED OR LOST SHIPMENTS
Check your order immediately upon arrival. All damage must be noted on the delivery receipt. Call Stenner Customer
Service at 800.683.2378 for all shortages and damages within seven (7) days of receipt.
SERVICE & REPAIRS
efore returning a pump for warranty or repair, remove chemical from pump tube by running water through the tube, and
then run the pump dry. Following expiration of the warranty period, Stenner Pump Company will clean and overhaul any
Stenner metering pump for a minimum labor charge plus necessary replacement parts and shipping. All metering pumps
received for overhaul will be restored to their original condition. The customer will be charged for missing parts unless
specific instructions are given. To return merchandise for repair, call Stenner at 800.683.2378 or 904.641.1666 for a
Return Merchandise Authorization (RMA) number.
DISCLAIMERS
The information in this manual is not intended for specific purposes.
The Stenner Pump Company reserves the right to make changes to prices, products, and specifications at any time
without prior notice.
The Modbus communication protocol is a product of the Modbus Organization, www.modbus.org.
TRADEMARKS
QuickPro®is a registered trademark of the Stenner Pump Company.
Santoprene®is a registered trademark of Exxon Mobil Corporation.
Versilon®is a registered trademark of Saint-Gobain Performance Plastics.
Pellethane®is a registered trademark of Lubrizol Advanced Materials, Inc.
Hastelloy®is a registered trademark of Haynes International, Inc.
AquaShield™is a trademark of Houghton International.

S Series FW 3.02.02 www.stenner.com
4
SA ETY INSTRUCTIONS
Warns about hazards that CAN cause death, serious personal injury, or property damage
if ignored.
ELECTRIC SHOCK HAZARD
RISK O ELECTRIC SHOCK
Connect only to a branch circuit protected by a ground-fault circuit-interrupter (GFCI). Contact a qualified
electrician if you cannot verify that the receptacle is protected by a GFCI.
RISQUE DE CHOC ELECTRIQUE
rancher seulement à un réseau électrique protégé par un DDFT. Contactez un électricien certifié si vous ne pouvez
pas vérifier que la prise est protégé par un DDFT.
PELIGRO DE DESCARGA ELECTRICA
Conecte a un circuito en derivación protegido por un interruptor de descarga a tierra (GFCI). Contacte a un
electricista certificado si no puede verificar que su receptáculo esté protegido por dicho interruptor (GFCI).
To reduce the risk of electric shock, replace damaged cord immediately. Contact the factory or an
authorized service facility for repair.
DO NOT alter the power cord or plug end. DO NOT use receptacle adapters.
DO NOT use pump with a damaged or altered power cord or plug. Contact the factory or
authorized service facility for repair.
After installation, the power supply plug must be accessible during use.
To reduce the risk of injury, do not permit children to use this product. This appliance is not to be
used by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction.
This pump has not been investigated for use in marine areas.
La pompe n’a pas été vérifiée et approuvée pour utilisation sur des applications de
installation marine.
Este dosificador no ha sido investigado para uso en áreas marinas.
EXPLOSION HAZARD
This equipment IS NOT explosion proof. DO NOT install in an explosive environment.
RISK O CHEMICAL EXPOSURE AND OVERDOSE
Potential for chemical burns, fire, explosion, personal injury, or property damage. To reduce risk of exposure, the use
of proper personal protective equipment is mandatory. To reduce risk of overdosing, follow proper installation methods
and recommendations. Check your local codes for additional guidelines.
RISK O IRE HAZARD
DO NOT install or operate on any flammable surface.
Pump is not recommended for installation in areas where leakage can cause personal injury or
property damage.
PELIGRO
PELIGRO
IMPORTANT SA ETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including
the following:
READ AND OLLOW ALL INSTRUCTIONS

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 5
SA ETY INSTRUCTIONS continued
Warns about hazards that WILL or CAN cause minor personal injury or property damage
if ignored.
To reduce risk of electric shock, pull plug before servicing this pump.
This pump has been evaluated for use with water only.
Non-submersible pump. Suitable for indoor and outdoor use.
Pompe non submersible. Adaptée à une utilisation aussi bien à l’intérieur qu’à l’extérieur.
Dosificador no sumergible. Adecuado para el uso interior y exterior.
PLUMBING
Chemical feed pump installation must always adhere to your local plumbing codes and requirements. e sure
installation does not constitute a cross connection. Check local plumbing codes for guidelines.
Electrical installation should adhere to all national and local codes. Consult licensed professional
for assistance with proper electrical installation.
Pump uses a class 2 switching power supply.
SAVE THESE INSTRUCTIONS
NOTICE: Indicates special instructions or general mandatory action.
This metering pump is portable and designed to be removable from the plumbing system without damage to
the connections.
This metering pump and its components have been tested for use with the following chemicals; Sodium Hypochlorite
(10-15%), Muriatic Acid (20-22 aume, 31.5% Hcl), and Soda Ash.
Cette a pompe de dosage et ses composants ont été testés pour utilisation avec les produits chimiques suivants;
Hypochlorite de Sodium (solution de 10-15%); Acide Muriatique (20-22 aume, 31.5% Hcl); Cendre de Soude.
efore installing or servicing the pump, read the pump manual for all safety information and complete instructions.
The pump is designed for installation and service by properly trained personnel.
No user replaceable parts inside.
Do not install at altitudes over 2000 meters.
CAUTION
CAUTION
CAUTION
CAUTION
CUIDADO
ATTENTION
CAUTION
CAUTION
CAUTION

S Series FW 3.02.02 www.stenner.com
6
LOW RATE OUTPUTS
NOTICE: The information within this chart is solely intended for use as a guide. The output data is an approximation based on pumping water under
a controlled testing environment. Many variables can affect the output of the pump. Stenner Pump Company recommends that all metering
pumps undergo field calibration by means of analytical testing to confirm their outputs.
25 psi (1.7 bar) max.
Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S3003 3 100:1 0.40–40 0.017–1.67 2.13– 213 0.036–3.56 1.51–151 0.063–6.31 63.09–6309 1.05–105
S3004 4 100:1 0.60–60 0.025–2.50 3.20–320 0.053–5.33 2.27–227 0.095–9.46 94.64–9464 1.58–158
S3005 5 100:1 0.85–85 0.035–3.54 4.53–453 0.076–7.56 3.22–322 0.134–13.41 134.07–13407 2.23–223
Approximate Output @ 50/60Hz
25 psi (1.7 bar) max.
Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S405X 5X 100:1 1.5–150.0 0.06–6.25 8.0–800.0 0.13–13.33 5.7–567.8 0.24–23.66 236.59–23658.82 3.94–394.31
Approximate Output @ 50/60Hz
100 psi (6.9 bar) max.
Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S3001 1 100:1 0.05–5 0.002–0.21 0.27–27 0.004–0.44 0.19–19 0.008–0.79 7.89–789 0.13–13
S3002 2 100:1 0.17–17 0.007–0.71 0.91–91 0.015–1.51 0.64–64 0.027–2.68 26.81–2681 0.45–45
S3007 7 100:1 0.40–40 0.017–1.67 2.13–213 0.036–3.56 1.51–151 0.063–6.31 63.09–6309 1.05–105
Approximate Output @ 50/60Hz
100 psi (6.9 bar) max.
Item umber Tube Turndown Gallons Gallons Ounces Ounces Liters Liters Milliliters Milliliters
Prefix Ratio per Day per Hour per Hour per Minute per Day per Hour per Hour per Minute
S407X 7X 100:1 0.6–60.0 0.03–2.50 3.2–320.0 0.053–5.34 2.3–227.0 0.09–9.46 94.64–9463.54 1.58–157.73
Approximate Output @ 50/60Hz
S30
S40

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 7
MATERIALS O CONSTRUCTION
S30 & S40
All Housings Polycarbonate
Pump Tube Santoprene®(FDA approved) or Versilon®
Pump Head Rollers Polyethylene
Roller Bushings Oil impregnated bronze
Suction/Discharge Tubing, Ferrules 1/4" & 6 mm Polyethylene (FDA approved)
Tube Fittings & Injection Fittings PVC or Polypropylene (both NSF listed)
Connecting uts PVC or Polypropylene (both NSF listed)
Suction Line Strainer and Cap PVC or Polypropylene (both NSF listed); ceramic weight
All Fasteners Stainless steel
Leak Detect Components Hastelloy®
S30
Check Valve Duckbill Santoprene®(FDA approved) or Pellethane®
3/8" Adapter PVC or Polypropylene (both NSF listed)
Pump Head Latches Polypropylene
S40
Ball Check Valve Components
-Ceramic ball (FDA approved); tantalum spring; FKM seat & O-ring OR
-Ceramic ball (FDA approved); stainless steel spring; EPDM seat; Santoprene®O-ring
Pump Head Latches Stainless steel

S Series FW 3.02.02 www.stenner.com
8
CHEMICAL RESISTANCE GUIDE
The information is provided ONLY as a guide to assist in determining chemical compatibility
for wetted components. Testing under the specific conditions of the application is recommended. Stenner Pump
Company assumes no responsibility for its accuracy. Outside factors including but not limited to temperature,
pressure, mechanical stress, and solution concentration can affect material compatibility in a particular application.
Stenner makes no warranty, expressed or implied, as to the accuracy of this guide or any materials’ suitability for
fitness or purpose for any application. User assumes all risk and liability for use of this guide.
Ratings Key – Chemical Effect
AFluid has minor or no effects
BFluid has minor to moderate effects
CFluid has severe effects
•No data available
Chemical / Solution
Chloroacetic Acid A C C C • • A
Chloroform C C C C A C • A
Chlorosulfonic Acid C C C C C •
Chromic Acid < 50% C A A C A
Chromium Salts A • A • • • •
Citric Acid C A • A A
Copper Chloride A A A A A • A C
Copper Sulfate A A A A A • A
Cottonseed Oil A A A • • A
d-Limonene C A C • •
Ethyl Acetate A C C C C •
Ethyl Alcohol C C • A •
Ethyl Chloride C C C C A C • A
Ethylene Dichloride C C C C A C •
Ethylene Glycol A A A A A A •
Ethylene Oxide A C C C C •
Eucalyptus Oil C C C • • • •
Fatty Acids C A A A C • A
Ferric Chloride A A A A A A C
Ferric Sulfate A A A A A •
Ferrous Chloride A A A A A C • C
Ferrous Sulfate A A A A A C •
Fluoboric Acid A C A C A • •
Fluosilicic Acid A A A A A C •
Formaldehyde < 40% A A C C • A
Formic Acid A C C C C A A
Glucose A A A A A A • A
Glycerin A A A A A A • A
Hydrochloric Acid 20% A C A A A C A C
Hydrochloric Acid 37% A C A A A C A C
Hydrocyanic Acid A A A A C A A
Hydrofluoric Acid < 48% A C A A C C C
Hydrofluoric Acid 48-75% A C C C A C C C
Hydrofluoric Acid, anhydrous C C C C • C C
Hydrogen Peroxide < 50% A A A A A A
Hydrogen Sulfide A A A C • • A
Iodine A A C A C A C
PP
Santoprene®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel
Chemical / Solution
Acetic Acid 20% A A A A A
Acetic Acid 30% C C A A A
Acetic Acid, Glacial C C C C C • A A
Acetic Anhydride C C C C C • A
Aliphatic Hydrocarbons • • • •
Aluminum Chloride A A A A A
Aluminum Sulfate A A A A A A A
Alums A A A A A A • A
Ammonium Acetate A A A • • A
Ammonium Carbonate A A A A A C •
Ammonium Chloride A A A C A
Ammonium Hydroxide A A A A A
Ammonium Nitrate A A A A C A A
Ammonium Phosphate A A A A A A • C
Ammonium Sulfate A A A A A A
Amyl Acetate A C C C C C • A
Aniline C C C C C A
Antimony Salts A A A • • • •
Arsenic Salts A A A • • • •
arium Hydroxide A A A A •
arium Salts A • A • A • •
eer A A A A A • A A
enzene C C C C • •
enzoic Acid A C A A A • A
leach 5.25% A A A A A • • •
oric Acid A A A A A A A A
romine A A C A C
utyl Acetate A C C C C C • A
utyric Acid A C C C A
Calcium Chloride A A A A • A
Calcium Hydroxide A C A A A •
Calcium Hypochlorite 5% A A A A • A
Calcium Salts A A A A • • •
Carbon Disulfide C C C C A • •
Carbon Tetrachloride C C C C A C •
Castor Oil A A • A • • A
Chlorine see Sodium Hypochlorite
PP
Santoprene®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 9
* Products tested and certified by IAPMO according to ANSI/NSF 61 for contact with Sodium Hypochlorite and Water only and ANSI/NSF 372.
Chemical / Solution
Silicone Oil C A A A C • A
Silver Nitrate A A A A A A •
Soap Solutions A A A C A A • A
Sodium A A A A • • • •
Sodium isulfate A A A A A • • C
Sodium isulfite A A A A A A •
Sodium orate A A A A A A •
Sodium Carbonate A A A A A A • A
Sodium Chlorate A A A A A C •
Sodium Chloride A A A A A A A
Sodium Dichromate 20% A • • A • • •
Sodium Hydroxide < 20% A A C A
Sodium Hydroxide 20-46.5% A C A C • C
Sodium Hypochlorite 5% A* A A A A C
Sodium Hypochlorite 6-15% A* A A A A C
Sodium Nitrate A A A A A C A
Sodium Silicate A A A A A A •
Sodium Sulfide A A A A A A • C
Sodium Sulfite A A A A A A • A
Solvents C • • • •
Soybean Oil A A A A • • A
Stannous Chloride 15% A A A A • • A
Stearic Acid A A • A
Sulfur Dioxide liquid A C C C • • A
Sulfur Trioxide C A C A • • C
Sulfuric Acid < 40% A C A C
Sulfuric Acid > 40% C C C C A C A C
Sulfurous Acid A A A C C •
Tannic Acid 10% A A A • A
Tanning Liquors A A A A A • • A
Tartaric Acid A A A A A A • C
Titanium Salts A A A • • • •
Triethanolamine A C C C C • • •
Trisodium Phosphate A A A A A • •
Tung Oil C C A • • •
Turpentine C C A C • A
Urea A A A •
Water & rine A A A A A • •
Zinc Chloride A A A A A A
Zinc Salts A A A A • • • •
NOTE: FKM tested to ANSI/NSF 61 with water only.
PP
Santoprene®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel
Chemical / Solution
Lactic Acid A A A A A
Lead Acetate A A A C C •
Linseed Oil A A A A A • A
Limonene C A C • •
Lubricating Oils C A C A • • A
Magnesium Chloride A A A A A A C
Magnesium Hydroxide A A A A A • A A
Magnesium Sulfate A A A A A A A
Malic Acid A A A A • A
Manganese Salts A A A A • • •
Mercuric Chloride A A A A A • • C
Methylene Chloride C C C C • A
Mineral Oil A A • • •
Mineral Spirits C A A • • A
Muriatic Acid, 20° aume A C A A A • • •
Nitric Acid < 10% A C A A A A
Nitric Acid 10-30% C A C A C A A
Nitric Acid 30-60% C C C A C A A
Nitric Acid 70% C C C A C A A
Nitric Acid, red fuming C C C C C C • •
Nitrous Acid A • • • •
Oleic Acid A C C C • A
Oleum 20-25% C C C C • • •
Oxalic Acid A C A A C A A
Palmitic Acid A A A C • A
Petroleum Distillates C C • • A A
Peracetic Acid 5% A A A • •
Peracetic Acid 15% A A • •
Phenol C C A C •
Phosphoric Acid A C A A A C A C
Phthalic Acid A C A A A • A
Pickling Solutions A C • • • • •
Plating Solutions A C • • A C • •
Polyphosphate A A A A • • • •
Potassium Carbonate A A A A A • •
Potassium Chlorate A A A A A •
Potassium Hydroxide A A A A C C A
Potassium Dichromate A A A A A • •
Potassium Iodide A A A • • A
Potassium Permanganate A A A A A • •
Sea Water A A A A A • A C
PP
Santoprene®
EPDM
Silicone
KM
LDPE
PVC
Versilon®
Tantalum Stainless
Steel

S Series FW 3.02.02 www.stenner.com
10
ACCESSORIES
S30
3 Connecting Nuts 1/4" or 3/8"
3 Ferrules 1/4" or 6 mm Europe
1 Injection Fitting 25 psi (1.7 bar) max. or 1 Duckbill Check Valve 100 psi (6.9 bar) max.
1 Weighted Suction Line Strainer 1/4", 3/8" or 6 mm Europe
1 20' Roll of Suction/Discharge Tubing 1/4" or 3/8", white, UV black or 6 mm white Europe
1 Additional Pump Tube
2 Additional Latches
1 Mounting racket
1 Quick Start Guide
S40
3 Connecting Nuts 3/8"
1 all Check Valve
1 Weighted Suction Line Strainer 3/8"
1 20' Roll Suction/Discharge Tubing 3/8", White or UV lack
1 Additional Pump Tube
1 Mounting racket
1 Quick Start Guide

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 11
GENERAL IN ORMATION
The S Series is an advanced peristaltic pump design with multiple programming features and
performance indicators. The S Series offers practical and flexible functions for municipal, wastewater
and industrial applications.
PUMP EATURES
• rushless DC Motor with ball bearing support
• Switch mode power supply
• Microcontroller
• lue OLED Display
• QuickPro® pump head with leak detect sensor
• Six button keypad on control panel
• Modbus RTU over RS-485 capability
M AI N M E NU
-CONFIGURATION
-C ON T R O L M O DE
-R UN P U MP
Button General unction Operating Mode unction
• Moves up in a menu
UP • Toggles between menu options Increases the speed percent in the Manual mode
• Increases a value
• Moves down in a menu
DOWN • Toggles between options Decreases the speed percent in the Manual mode
• Decreases a value
PRIME N/A Runs pump at 100% speed while button is pressed
ON/O N/A Turns pump control ON or OFF
WARNING: DOES NOT REMOVE POWER
BACK Moves one step back in a menu when permitted Cycles the display to show different units of output
ENTER Sets a value Press and hold for 2 seconds to go to the
Main Menu
SETUP
The very first time the pump is turned on, the display will show the Firmware Version followed by the Main Menu screen.
If the pump was previously programmed, the display will return to the mode it was in when it was turned off or if power
was lost.
Main Menu
- Configuration
- Control Mode
- Run Pump
FW: 3.02.02
S SERIES
The display will indicate
the pump's software version.
OUTPUT
• 0.05 – 150.0 gpd, pressures to 25 psi
• 0.05 – 60.0 gpd, pressures to 100 psi
CONTROL PANEL
NAVIGATION BUTTONS

S Series FW 3.02.02 www.stenner.com
12
GENERAL IN ORMATION continued
Mandatory Calibration
From the Configuration menu, select GPD/LPD Calibration, and enter your pump’s ACTUAL maximum flow rate
output. Refer to illustration below.
IMPORTANT!
The pump’s ACTUAL maximum flow rate entry:
・
Affects flow rate output displayed on the screen during operation in all modes.
・
Contributes to overall calculation of flow rate output in the PPM modes.
Program Applicable Pump Parameters
In Configuration menu, program applicable pump parameters, refer to chart below.
1
Enter max pump flow
__0.0 GPD
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
Configuration
- Units
- Clock
- Calibration
adjust
set
2
Pump Parameters Description Control Mode
Display rightness Optimal setting is < 50% for extended periods. All
Units Default is Gallons; enter Liters, if preferred. All
Clock 24-hr format. Enter current time of day and day of the week. All
Leak Detect Calibrate sensitivity to distinguish between water & your chemical. All
Tube Timer Enter number of hours you want pump to run before display All
shows TU E CHANGE.
Password Program a password to prevent unauthorized changes to pump settings. All
Output Relays Three individual relays available; rated for 24VDC @ 50mA max. All
Program communication for:
• S Series to back-up S Series
• S Series to another device
Signal Calibration If factory settings are not sufficient, calibrate the pump using a 4-20mA, 0-10VDC
process meter or powered transmitter.
Reset Totalizer Option to reset the total tallied amount of water treated. Pulse, Hall Effect, PPM
Modbus Setup Modbus RTU over RS-485 capability; pump firmware 3.02.02 or higher Manual, 4-20mA, 0-10VDC, Pulse
3
4
5
HOW TO GET STARTED SUMMARY
Select Mode of Operation
In Control Modes menu, select your mode of operation.
Program the Options
In your selected control mode, program the options relevant to your application.
un the Pump

US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 13
GENERAL IN ORMATION continued
COMMUNICATION
PER ORMANCE INDICATORS ACTIVATED BY PUMP CONDITIONS
Display Alarm Three Output Relays to
on control panel pump, system or device
Tube Change ✓ ✓
Tube Leak ✓ ✓
Standby ✓ ✓
Drive Fault ✓ ✓
Off ✓ ✓
Run –––––– ✓
Mode Change –––––– ✓
Transfer**–––––– ✓
Repeat Pulse –––––– ✓
High Signal ✓ ✓ 4-20mA*or 0-10VDC*
Low Signal ✓ ✓ 4-20mA*or 0-10VDC*
High Flow ✓ ✓ Hall Effect or PPM Feed: Hall Effect
Low Flow ✓ ✓ Hall Effect
Signal Overrun ✓ ✓ Pulse
* Scalable, invertible
** Transfer operation from a primary pump to a backup pump via a relay.
Pump Conditions Modes of Operation
Communication
Manual, 4-20mA*, 0-10VDC*,
Pulse, 7 Day Timer, Cycle Timer,
PPM Feed: Flow switch
All Modes of Operation
REMOTE COMMUNICATION CAPABILITY WITH MODBUS RTU over RS-485
Requirements
• S Series Pump with firmware version 3.02.02 or higher
• Applicable modes of operation: Manual, 4-20mA, 010VDC, or Pulse
• Stenner Modbus manual
• Modbus RS-485 communication cable & 1 three terminal, liquid tight junction;
purchased separately, part number MOD100

S Series FW 3.02.02 www.stenner.com
14
CON IGURATION MENU
SUMMARY
Configuration of the pump parameters should be completed at the initial setup.
From the Main Menu, select Configuration and follow
Display rightness
Units
Clock
Calibration
Password
Tube Timer
Reset Totalizer
Leak Detect
Outputs
Modbus Setup
Firmware Version
Reset Pump.

Returns to Configuration menu
US and Canada 800.683.2378, International 904.641.1666 S Series FW 3.02.02 15
Display Brightness
Configuration
- Display rightness
- Units
- Clock
100%
adjust set
CON IGURATION MENU continued
DISPLAY BRIGHTNESS
Allows user to adjust the brightness level of the pump display from 0% to 100%. There is some
visibility at the minimum setting.
NOTE: For best performance and longevity, the display brightness should not be set higher than 50% for extended periods.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

S Series FW 3.02.02 www.stenner.com
16
Units
Configuration
- Display rightness
- Units
- Clock
Gallons
Units
Liters
Returns to Configuration menu.
Returns to Configuration menu.
adjust set
adjust set
CON IGURATION MENU continued
UNITS
Allows the user to set the unit of measure to Gallons or Liters. The selection appears in the pump
display during Control Mode programming.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

US and Canada 800.683.2378, International 904.641.1666 17
Today is
Configuration
- Display rightness
- Units
- Clock
Sunday
The time is
00:00:00
adjustsun- sat set set
CON IGURATION MENU continued
CLOCK
Allows the user to set the current day of the week and the time of the day. The time is set in a 24 hour
clock format only.
NOTE: For the time, the first two digits that control the hour are highlighted together.
Returns to Configuration menu
When ENTE is pressed for the last digit
in the time of day, the display returns to
Configuration menu
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.

To Configuration menu
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
CON IGURATION MENU continued
Enter max pump flow
__0.0 GPD
adjust set
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
CALIBRATION page 1 of 2
Allows user to set the pump’s maximum output. The units displayed in the Calibration submenu are
controlled by the setting made in the Units submenu.
IMPORTANT: The value entered (in Calibration) for the pump’s maximum output is used to calculate the pump’s
required output for the operating mode in Run Pump. The value is also used to calculate the pump's required run
speed in the PPM eed submenu in Control Mode. For the most accurate dosing possible, determine the actual pump
output. Conduct a drawdown from a graduated calibration column against the discharge run and pressure, equivalent to
the intended installation.
GPD or LPD is selected in
Units under Configuration
When ENTE is
pressed for the
final digit in
Calibration,
the display
returns to the
Calibration menu
Configuration
- Units
- Clock
- Calibration
To
Calibration menu
Continued on next page
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.
www.stenner.com
18

To Signal Calibration menu
To Signal Calibration menu
Calibration
- GPD/LPD Calibration
- Signal Calibration
- GO TO CONFIG MENU
Signal Calibration
- 4-20mA IN
- 0- 10V IN
- 4-20mA OUT
To top of
Calibration menu
Signal Calibration
- 0- 10V IN
- 4-20mA OUT
- GO TO CAL MENU
Connect pump to 0-10V loop
using a process meter or powered transmitter
CON IGURATION MENU continued
CALIBRATION page 2 of 2
Allows user to calibrate analog signal inputs and outputs.
0 - 10V IN Set
Input 0V
0 - 10V IN Set
Input 10V
set back
set
Signal Calibration
- 4-20mA IN
- 0 - 10V IN
- 4-20mA OUT
When pump indicates to input
10V, bring loop to 10.0V (or
desired level). Press ENTE .
When pump indicates to input
0V, bring loop to 0.0V (or
desired level). Press ENTE .
Signal Calibration
- 4-20mA IN
- 0 -
10V IN
- 4-20mA OUT
Continued from previous page
Connect process meter to 4-20mA output signal
4mA OUT Set
0508
adjust
set
20mA OUT Set
2584
set back
In 20mA Out Set, press the
UP or DOWN button to adjust
the signal until the meter
reads 20.0. Press ENTE .
In 4mA Out Set, press the UP
or DOWN button to adjust the
signal until the meter reads
4.0. Press ENTE .
Input 4mA
4-20mA IN Set
Input 20mA
set back
set
Connect pump to 4-20mA loop
using a process meter or powered transmitter
4-20mA IN Set
When pump indicates to input
20mA, bring loop to 20.0mA
(or desired level). Press ENTE .
When pump indicates to input
4mA, bring loop to 4.0mA
(or desired level). Press ENTE .
To Signal Calibration menu
US and Canada 800.683.2378, International 904.641.1666 19
adjust
CAUTION: 4-20mA and
0-10VDC input signals
are pre-calibrated at
the factory. Only change
the input calibration if
the factory settings are
not sufficient.

The pump will indicate if the password was
accepted or not and the screen
will return to Configuration menu.
S Series FW 3.02.02 www.stenner.com
20
CON IGURATION MENU continued
PASSWORD
Allows user to set a password to prevent unauthorized changes to the pump settings.
• Each digit can be set for 0-9 or A-Z.
• When the password is set, it must be entered during the Operating Display mode (in Run Pump) in order to enter the
Main Menu.
• Leaving the password blank disables the password feature. The password is disabled by default.
Displays message for 3 seconds and
returns to Configuration menu.
Configuration
- Clock
- Calibration
- Password
Enter Password
0-9, A-Z set
Confirm Password
0-9, A-Z set
PASSWORD
ACCEPTED
If password was
accepted.
If no password was entered.
Displays message
for 3 seconds
and returns to
Configuration
menu.
Sets a value in a menu
NAVIGATION
Moves one step back in
a menu, when permitted
Moves up in a menu, toggles
between options, or increase a value
Moves down in a menu, toggles
between options, or decreases a value
Holding the or button causes the numbers to change rapidly.
To Configuration menu
PASSWORD DID NOT
MATCH. PLEASE
RE-ENTER PASSWORD
ok
PASSWORD
DISABLED
If password
was not accepted.